参数资料
型号: MC68HCL05P1AP
厂商: FREESCALE SEMICONDUCTOR INC
元件分类: 微控制器/微处理器
英文描述: 8-BIT, MROM, 2.1 MHz, MICROCONTROLLER, PDIP28
封装: PLASTIC, DIP-28
文件页数: 58/124页
文件大小: 3724K
代理商: MC68HCL05P1AP
Interrupts
Reset Interrupt Sequence
MC68HC05P1A Rev. 3.0
General Release Specification
Interrupts
NON-DISCLOSURE
AGREEMENT
REQUIRED
4.3 Reset Interrupt Sequence
The reset function is not in the strictest sense an interrupt; however, it is
acted upon in a similar manner, as shown in Figure 4-1. A low level input
on the RESET pin or internally generated RST signal causes the
program to vector to its starting address, which is specified by the
contents of memory locations $1FFE and $1FFF. The I bit in the
condition code register is also set. The MCU is configured to a known
state during a reset, as described in Section 5. Resets.
4.4 Software Interrupt (SWI)
The SWI is an executable instruction. It is also a non-maskable interrupt
since it is executed regardless of the state of the I bit in the CCR. As with
any instruction, interrupts pending during the previous instruction will be
serviced before the SWI opcode is fetched. The interrupt service routine
address for the SWI instruction is specified by the contents of memory
locations $1FFC and $1FFD.
4.5 Hardware Interrupts
All hardware interrupts are maskable by the I bit in the CCR. If the I bit
is set, all hardware interrupts (internal and external) are disabled.
Clearing the I bit enables the hardware interrupts. The hardware
interrupts are explained in the following sections.
4.5.1 External Interrupt (IRQ)
The IRQ pin drives an asynchronous interrupt to the CPU. An edge
detector flip-flop is latched on the falling edge of IRQ. If either the output
from the internal edge detector flip-flops or the level on the IRQ pin is
low, a request is synchronized to the CPU to generate the IRQ interrupt.
If the edge-sensitive only mask option is selected, the output of the
internal edge detector flip-flop is sampled and the input level on the IRQ
pin is ignored. The interrupt service routine address is specified by the
contents of memory locations $1FFA and $1FFB. A block diagram of the
IRQ function is shown in Figure 4-2.
F
re
e
sc
a
le
S
e
m
ic
o
n
d
u
c
to
r,
I
Freescale Semiconductor, Inc.
For More Information On This Product,
Go to: www.freescale.com
n
c
..
.
相关PDF资料
PDF描述
MPC8280VRUPEX 32-BIT, 450 MHz, RISC PROCESSOR, PBGA516
MPC8280ZQSLDX 32-BIT, 375 MHz, RISC PROCESSOR, PBGA516
MPC8270CZQQLDX 32-BIT, 333 MHz, RISC PROCESSOR, PBGA516
MPC8270CZQTPEX 32-BIT, 400 MHz, RISC PROCESSOR, PBGA516
MPC8275CVRSLDX 32-BIT, 375 MHz, RISC PROCESSOR, PBGA516
相关代理商/技术参数
参数描述
MC68HCP11A1CFN3 功能描述:8位微控制器 -MCU 8-bit HCMOS single chip MCU RoHS:否 制造商:Silicon Labs 核心:8051 处理器系列:C8051F39x 数据总线宽度:8 bit 最大时钟频率:50 MHz 程序存储器大小:16 KB 数据 RAM 大小:1 KB 片上 ADC:Yes 工作电源电压:1.8 V to 3.6 V 工作温度范围:- 40 C to + 105 C 封装 / 箱体:QFN-20 安装风格:SMD/SMT
MC68HCP11A1FN 制造商:MOTORALA 功能描述:
MC68HCP11E0CP2 制造商:Rochester Electronics LLC 功能描述:- Bulk
MC68HCP11E0FN 功能描述:MICROCONTROLLER MCU 8ADC 3MHC RoHS:否 类别:集成电路 (IC) >> 嵌入式 - 微控制器, 系列:HC11 标准包装:250 系列:56F8xxx 核心处理器:56800E 芯体尺寸:16-位 速度:60MHz 连通性:CAN,SCI,SPI 外围设备:POR,PWM,温度传感器,WDT 输入/输出数:21 程序存储器容量:40KB(20K x 16) 程序存储器类型:闪存 EEPROM 大小:- RAM 容量:6K x 16 电压 - 电源 (Vcc/Vdd):2.25 V ~ 3.6 V 数据转换器:A/D 6x12b 振荡器型:内部 工作温度:-40°C ~ 125°C 封装/外壳:48-LQFP 包装:托盘 配用:MC56F8323EVME-ND - BOARD EVALUATION MC56F8323
MC68HCP11E0FNE 功能描述:8位微控制器 -MCU 8B MCU 512RAM COP A/D RoHS:否 制造商:Silicon Labs 核心:8051 处理器系列:C8051F39x 数据总线宽度:8 bit 最大时钟频率:50 MHz 程序存储器大小:16 KB 数据 RAM 大小:1 KB 片上 ADC:Yes 工作电源电压:1.8 V to 3.6 V 工作温度范围:- 40 C to + 105 C 封装 / 箱体:QFN-20 安装风格:SMD/SMT