收藏本站
参数资料
型号： MC68L11D0FNE2
厂商： FREESCALE SEMICONDUCTOR INC
元件分类： 微控制器/微处理器
英文描述： 8-BIT, 2 MHz, MICROCONTROLLER, PQCC44
封装： PLASTIC, LCC-44
文件页数： 64/138页
文件大小： 1047K
代理商： MC68L11D0FNE2
Programmable Read-Only Memory (PROM)
MC68HC711D3 Data Sheet, Rev. 2.1
Freescale Semiconductor
31
ROMON — PROM Enable Bit
This bit is set out of reset, enabling the EPROM or OTPROM in all modes. This bit is writable once in
normal modes (SMOD = 0), but is writable at any time in special modes (SMOD = 1).
1 = PROM is present in the memory map.
0 = PROM is disabled from the memory map.
NOTE
In expanded mode out of reset, the EPROM or OTPROM is located at
$7000–$7FFF. In all other modes, the PROM resides at $F000–$FFFF.
2.4 Programmable Read-Only Memory (PROM)
The MC68HC711D3 has 4-Kbytes of one-time programmable read-only memory (OTPROM). The PROM
address is $F000–$FFFF in all modes except expanded multiplexed. In expanded- multiplexed mode, the
PROM is located at $7000–$7FFF after reset.
The on-chip read-only memory (ROM) of an MC68HC711D3 is programmed in MCU mode. In this mode,
the PROM is programmed through the MCU in the bootstrap or test modes. The erased state of a PROM
byte is $FF.
Using the on-chip OTPROM programming feature requires an external 12-volt nominal power supply
(VPP). Normal programming is accomplished using the OTPROM programming register (PPROG).
As described in the following subsections, these two methods of programming and verifying EPROM are
possible:
1.
Programming an individual EPROM address
2.
Programming the EPROM with downloaded data
2.4.1 Programming an Individual EPROM Address
In this method, the MCU programs its own EPROM by controlling the PPROG register. Use these
procedures to program the EPROM through the MCU with:
The ROMON bit set in the CONFIG register
The 12-volt nominal programming voltage present on the XIRQ/VPP pin
The IRQ pin must be pulled high.
EPROG
LDAB
#$20
STAB
$003B
Set ELAT bit (PGM = 0) to enable
EPROM latches.
STAA
$0,X
Store data to EPROM address
LDAB
#$21
STAB
$003B
Set PGM bit with ELAT = 1 to enable
EPROM programming voltage
JSR
DLYEP
Delay 2–4 ms
CLR
$003B
Turn off programming voltage and set
to READ mode
相关PDF资料
PDF描述
MC908GR60AVFAR2 8-BIT, FLASH, 8 MHz, MICROCONTROLLER, PQFP48
MC908GZ48VFAE 8-BIT, FLASH, 8 MHz, MICROCONTROLLER, PQFP48
MC908GZ60CFJE 8-BIT, FLASH, 8 MHz, MICROCONTROLLER, PQFP32
MC9S08RE16FGE 8-BIT, FLASH, 8 MHz, MICROCONTROLLER, PQFP44
MC9S12C96CPBR2 16-BIT, FLASH, 25 MHz, MICROCONTROLLER, PQFP52
相关代理商/技术参数
参数描述
MC68L11E0FN2 制造商:Rochester Electronics LLC 功能描述:8-BIT MCU,512RAM,A/D,LVDC - Bulk
MC68L11E0FNE2 功能描述:IC MCU 8BIT LV 512RAM 52-PLCC RoHS:是 类别:集成电路 (IC) >> 嵌入式 - 微控制器， 系列:HC11 标准包装:1 系列:87C 核心处理器:MCS 51 芯体尺寸:8-位 速度:16MHz 连通性:SIO 外围设备:- 输入/输出数:32 程序存储器容量:8KB（8K x 8） 程序存储器类型:OTP EEPROM 大小:- RAM 容量:256 x 8 电压 - 电源 (Vcc/Vdd):4 V ~ 6 V 数据转换器:- 振荡器型:外部 工作温度:0°C ~ 70°C 封装/外壳:44-DIP 包装:管件 其它名称:864285
MC68L11E1CFNE2 功能描述:8位微控制器 -MCU 8B MCU RAM EE A/D LVDC RoHS:否 制造商:Silicon Labs 核心:8051 处理器系列:C8051F39x 数据总线宽度:8 bit 最大时钟频率:50 MHz 程序存储器大小:16 KB 数据 RAM 大小:1 KB 片上 ADC:Yes 工作电源电压:1.8 V to 3.6 V 工作温度范围:- 40 C to + 105 C 封装 / 箱体:QFN-20 安装风格:SMD/SMT
MC68L11E1FNE2 功能描述:8位微控制器 -MCU 8B MCU RAM EE A/D LVD RoHS:否 制造商:Silicon Labs 核心:8051 处理器系列:C8051F39x 数据总线宽度:8 bit 最大时钟频率:50 MHz 程序存储器大小:16 KB 数据 RAM 大小:1 KB 片上 ADC:Yes 工作电源电压:1.8 V to 3.6 V 工作温度范围:- 40 C to + 105 C 封装 / 箱体:QFN-20 安装风格:SMD/SMT
MC68L11F1CFNE3 功能描述:8位微控制器 -MCU 8B MCU 1KRAM 512BYTES RoHS:否 制造商:Silicon Labs 核心:8051 处理器系列:C8051F39x 数据总线宽度:8 bit 最大时钟频率:50 MHz 程序存储器大小:16 KB 数据 RAM 大小:1 KB 片上 ADC:Yes 工作电源电压:1.8 V to 3.6 V 工作温度范围:- 40 C to + 105 C 封装 / 箱体:QFN-20 安装风格:SMD/SMT
发布紧急采购，3分钟左右您将得到回复。

采购需求

(若只采购一条型号，填写一行即可)

发布成功！您可以继续发布采购。也可以进入我的后台，查看报价

发布成功！您可以继续发布采购。也可以进入我的后台，查看报价

*型号 *数量 厂商 批号 封装
添加更多采购

我的联系方式

*
*
*