参数资料
型号: MC68L11D0FNE2
厂商: FREESCALE SEMICONDUCTOR INC
元件分类: 微控制器/微处理器
英文描述: 8-BIT, 2 MHz, MICROCONTROLLER, PQCC44
封装: PLASTIC, LCC-44
文件页数: 83/138页
文件大小: 1047K
代理商: MC68L11D0FNE2
Interrupts
MC68HC711D3 Data Sheet, Rev. 2.1
Freescale Semiconductor
49
Bits 7, 6, and 2 — Not implemented
Always read 0.
IRQE — IRQ Edge/Level Sensitivity Select
This bit can be written only once during the first 64 E-clock cycles after reset in normal modes.
1 = IRQ is configured to respond only to falling edges.
0 = IRQ is configured for low-level wired-OR operation.
DLY — Stop Mode Exit Turnon Delay
This bit is set during reset and can be written only once during the first 64 E-clock cycles after reset in
normal modes. If an external clock source rather than a crystal is used, the stabilization delay can be
inhibited because the clock source is assumed to be stable.
1 = A stabilization delay of 4064 E-clock cycles is imposed before processing resumes after a stop
mode wakeup.
0 = No stabilization delay is imposed after story recovery.
CME — Clock Monitor Enable
1 = Clock monitor circuit is enabled.
0 = Clock monitor circuit is disabled.
CR1 and CR0 — COP Timer Rate Selects
The COP system is driven by a constant frequency of E
÷ 215. These two bits specify an additional
divide-by value to arrive at the COP timeout rate. These bits are cleared during reset and can be written
only once during the first 64 E-clock cycles after reset in normal modes. The value of these bits is:
4.3 Interrupts
Excluding reset-type interrupts, there are 17 hardware interrupts and one software interrupt that can be
generated from all the possible sources. These interrupts can be divided into two categories: maskable
and non-maskable. Fifteen of the interrupts can be masked using the I bit of the condition code register
(CCR). All the on-chip (hardware) interrupts are individually maskable by local control bits. The software
interrupt is non-maskable. The external input to the XIRQ pin is considered a non-maskable interrupt
because it cannot be masked by software once it is enabled. However, it is masked during reset and upon
receipt of an interrupt at the XIRQ pin. Illegal opcode is also a non-maskable interrupt.
Address:
$0039
Bit 7
654321
Bit 0
Read:
0
IRQE
DLY
CME
0
CR1
CR0
Write:
Reset:
00010000
Figure 4-2. System Configuration Options Register (OPTION)
CR1
CR0
E
÷ 215
Divided By
00
1
01
4
10
16
11
64
相关PDF资料
PDF描述
MC908GR60AVFAR2 8-BIT, FLASH, 8 MHz, MICROCONTROLLER, PQFP48
MC908GZ48VFAE 8-BIT, FLASH, 8 MHz, MICROCONTROLLER, PQFP48
MC908GZ60CFJE 8-BIT, FLASH, 8 MHz, MICROCONTROLLER, PQFP32
MC9S08RE16FGE 8-BIT, FLASH, 8 MHz, MICROCONTROLLER, PQFP44
MC9S12C96CPBR2 16-BIT, FLASH, 25 MHz, MICROCONTROLLER, PQFP52
相关代理商/技术参数
参数描述
MC68L11E0FN2 制造商:Rochester Electronics LLC 功能描述:8-BIT MCU,512RAM,A/D,LVDC - Bulk
MC68L11E0FNE2 功能描述:IC MCU 8BIT LV 512RAM 52-PLCC RoHS:是 类别:集成电路 (IC) >> 嵌入式 - 微控制器, 系列:HC11 标准包装:1 系列:87C 核心处理器:MCS 51 芯体尺寸:8-位 速度:16MHz 连通性:SIO 外围设备:- 输入/输出数:32 程序存储器容量:8KB(8K x 8) 程序存储器类型:OTP EEPROM 大小:- RAM 容量:256 x 8 电压 - 电源 (Vcc/Vdd):4 V ~ 6 V 数据转换器:- 振荡器型:外部 工作温度:0°C ~ 70°C 封装/外壳:44-DIP 包装:管件 其它名称:864285
MC68L11E1CFNE2 功能描述:8位微控制器 -MCU 8B MCU RAM EE A/D LVDC RoHS:否 制造商:Silicon Labs 核心:8051 处理器系列:C8051F39x 数据总线宽度:8 bit 最大时钟频率:50 MHz 程序存储器大小:16 KB 数据 RAM 大小:1 KB 片上 ADC:Yes 工作电源电压:1.8 V to 3.6 V 工作温度范围:- 40 C to + 105 C 封装 / 箱体:QFN-20 安装风格:SMD/SMT
MC68L11E1FNE2 功能描述:8位微控制器 -MCU 8B MCU RAM EE A/D LVD RoHS:否 制造商:Silicon Labs 核心:8051 处理器系列:C8051F39x 数据总线宽度:8 bit 最大时钟频率:50 MHz 程序存储器大小:16 KB 数据 RAM 大小:1 KB 片上 ADC:Yes 工作电源电压:1.8 V to 3.6 V 工作温度范围:- 40 C to + 105 C 封装 / 箱体:QFN-20 安装风格:SMD/SMT
MC68L11F1CFNE3 功能描述:8位微控制器 -MCU 8B MCU 1KRAM 512BYTES RoHS:否 制造商:Silicon Labs 核心:8051 处理器系列:C8051F39x 数据总线宽度:8 bit 最大时钟频率:50 MHz 程序存储器大小:16 KB 数据 RAM 大小:1 KB 片上 ADC:Yes 工作电源电压:1.8 V to 3.6 V 工作温度范围:- 40 C to + 105 C 封装 / 箱体:QFN-20 安装风格:SMD/SMT