- 您现在的位置：买卖IC网 > PDF目录3976 > MC7448HX1000NC (Freescale Semiconductor)IC MPU RISC 32BIT 360-FCCBGA PDF资料下载
参数资料
| 型号： | MC7448HX1000NC |
| 厂商： | Freescale Semiconductor |
| 文件页数： | 39/60页 |
| 文件大小： | 0K |
| 描述： | IC MPU RISC 32BIT 360-FCCBGA |
| 标准包装： | 44 |
| 系列： | MPC74xx |
| 处理器类型： | 32-位 MPC74xx PowerPC |
| 速度： | 1.0GHz |
| 电压： | 1V |
| 安装类型： | 表面贴装 |
| 封装/外壳： | 360-BCBGA，FCCBGA |
| 供应商设备封装： | 360-FCCBGA（25x25） |
| 包装： | 托盘 |
第1页第2页第3页第4页第5页第6页第7页第8页第9页第10页第11页第12页第13页第14页第15页第16页第17页第18页第19页第20页第21页第22页第23页第24页第25页第26页第27页第28页第29页第30页第31页第32页第33页第34页第35页第36页第37页第38页当前第39页第40页第41页第42页第43页第44页第45页第46页第47页第48页第49页第50页第51页第52页第53页第54页第55页第56页第57页第58页第59页第60页
MPC7448 RISC Microprocessor Hardware Specifications, Rev. 4
44
Freescale Semiconductor
System Design Information
to fully control the processor. If the target system has independent reset sources, such as voltage monitors,
watchdog timers, power supply failures, or push-button switches, then the COP reset signals must be
merged into these signals with logic.
The arrangement shown in Figure 21 allows the COP port to independently assert HRESET or TRST,
while ensuring that the target can drive HRESET as well. If the JTAG interface and COP header will not
be used, TRST should be tied to HRESET through a 0-
Ω isolation resistor so that it is asserted when the
system reset signal (HRESET) is asserted, ensuring that the JTAG scan chain is initialized during
power-on. Although Freescale recommends that the COP header be designed into the system as shown in
Figure 21, if this is not possible, the isolation resistor will allow future access to TRST in the case where
a JTAG interface may need to be wired onto the system in debug situations.
The COP header shown in Figure 21 adds many benefits—breakpoints, watchpoints, register and memory
examination/modification, and other standard debugger features are possible through this interface—and
can be as inexpensive as an unpopulated footprint for a header to be added when needed.
The COP interface has a standard header for connection to the target system, based on the 0.025"
square-post, 0.100" centered header assembly (often called a Berg header). The connector typically has
pin 14 removed as a connector key.
There is no standardized way to number the COP header shown in Figure 21; consequently, many different
pin numbers have been observed from emulator vendors. Some are numbered top-to-bottom then
left-to-right, while others use left-to-right then top-to-bottom, while still others number the pins counter
clockwise from pin 1 (as with an IC). Regardless of the numbering, the signal placement recommended in
Figure 21 is common to all known emulators.
The QACK signal shown in Figure 21 is usually connected to the bridge chip or other system control logic
in a system and is an input to the MPC7448 informing it that it can go into the quiescent state. Under
normal operation this occurs during a low-power mode selection. In order for COP to work, the MPC7448
must see this signal asserted (pulled down). While shown on the COP header, not all emulator products
drive this signal. If the product does not, a pull-down resistor can be populated to assert this signal.
Additionally, some emulator products implement open-drain type outputs and can only drive QACK
asserted; for these tools, a pull-up resistor can be implemented to ensure this signal is negated when it is
not being driven by the tool. Note that the pull-up and pull-down resistors on the QACK signal are
mutually exclusive and it is never necessary to populate both in a system. To preserve correct power-down
operation, QACK should be merged through logic so that it also can be driven by the bridge or system
logic.
相关PDF资料 |
PDF描述 |
|---|---|
| EMC65DTEH | CONN EDGECARD 130POS .100 EYELET |
| MC7448HX1000LC | IC MPU RISC 32BIT 360-FCCBGA |
| FMC65DRES | CONN EDGECARD 130POS .100 EYELET |
| FMC65DREN | CONN EDGECARD 130POS .100 EYELET |
| MC7447AVU1167NB | IC MPU RISC 32BIT 360-BGA |
相关代理商/技术参数 |
参数描述 |
|---|---|
| MC7448HX1000ND | 功能描述:微处理器 - MPU APL8 RV2.2.1 1.0V 105C RoHS:否 制造商:Atmel 处理器系列:SAMA5D31 核心:ARM Cortex A5 数据总线宽度:32 bit 最大时钟频率:536 MHz 程序存储器大小:32 KB 数据 RAM 大小:128 KB 接口类型:CAN, Ethernet, LIN, SPI,TWI, UART, USB 工作电源电压:1.8 V to 3.3 V 最大工作温度:+ 85 C 安装风格:SMD/SMT 封装 / 箱体:FBGA-324 |
| MC7448HX1250N | 制造商:FREESCALE 制造商全称:Freescale Semiconductor, Inc 功能描述:MPC7448 Hardware Specifications |
| MC7448HX1250NC | 功能描述:IC MPU RISC 32BIT 360-FCCBGA RoHS:否 类别:集成电路 (IC) >> 嵌入式 - 微处理器 系列:MPC74xx 标准包装:1 系列:MPC85xx 处理器类型:32-位 MPC85xx PowerQUICC III 特点:- 速度:1.2GHz 电压:1.1V 安装类型:表面贴装 封装/外壳:783-BBGA，FCBGA 供应商设备封装:783-FCPBGA（29x29） 包装:托盘 |
| MC7448HX1250ND | 功能描述:微处理器 - MPU APL8 RV2.2.1 1.1V 105C RoHS:否 制造商:Atmel 处理器系列:SAMA5D31 核心:ARM Cortex A5 数据总线宽度:32 bit 最大时钟频率:536 MHz 程序存储器大小:32 KB 数据 RAM 大小:128 KB 接口类型:CAN, Ethernet, LIN, SPI,TWI, UART, USB 工作电源电压:1.8 V to 3.3 V 最大工作温度:+ 85 C 安装风格:SMD/SMT 封装 / 箱体:FBGA-324 |
| MC7448HX1267NC | 功能描述:IC MPU RISC 32BIT 360-FCCBGA RoHS:否 类别:集成电路 (IC) >> 嵌入式 - 微处理器 系列:MPC74xx 标准包装:1 系列:MPC85xx 处理器类型:32-位 MPC85xx PowerQUICC III 特点:- 速度:1.2GHz 电压:1.1V 安装类型:表面贴装 封装/外壳:783-BBGA，FCBGA 供应商设备封装:783-FCPBGA（29x29） 包装:托盘 |
发布紧急采购，3分钟左右您将得到回复。