- 您现在的位置：买卖IC网 > PDF目录5091 > MCP1700-2702E/TO (Microchip Technology)IC REG LDO 2.7V .25A TO-92-3 PDF资料下载
参数资料
| 型号： | MCP1700-2702E/TO |
| 厂商： | Microchip Technology |
| 文件页数： | 10/24页 |
| 文件大小： | 0K |
| 描述： | IC REG LDO 2.7V .25A TO-92-3 |
| 标准包装： | 1,000 |
| 稳压器拓扑结构： | 正，固定式 |
| 输出电压： | 2.7V |
| 输入电压： | 最高 6V |
| 电压 - 压降（标准）： | 0.178V @ 250mA |
| 稳压器数量： | 1 |
| 电流 - 输出： | 250mA（最小） |
| 工作温度： | -40°C ~ 125°C |
| 安装类型： | 通孔 |
| 封装/外壳： | TO-226-3、TO-92-3 标准主体 |
| 供应商设备封装： | TO-92-3 |
| 包装： | 散装 |
MCP1700
3.0
PIN DESCRIPTIONS
TABLE 3-1:
PIN FUNCTION TABLE
Pin No.
SOT-23
1
2
3
Pin No.
SOT-89
1
3
2
Pin No.
TO-92
1
3
2
Name
GND
V OUT
V IN
Function
Ground Terminal
Regulated Voltage Output
Unregulated Supply Voltage
3.1
Ground Terminal (GND)
3.3
Unregulated Input Voltage Pin
Regulator ground. Tie GND to the negative side of the
output and the negative side of the input capacitor.
Only the LDO bias current (1.6 μA typical) flows out of
this pin; there is no high current. The LDO output
regulation is referenced to this pin. Minimize voltage
drops between this pin and the negative side of the
load.
3.2 Regulated Output Voltage (V OUT )
Connect V OUT to the positive side of the load and the
positive terminal of the output capacitor. The positive
side of the output capacitor should be physically
located as close to the LDO V OUT pin as is practical.
The current flowing out of this pin is equal to the DC
load current.
DS21826B-page 10
(V IN )
Connect V IN to the input unregulated source voltage.
Like all low dropout linear regulators, low source
impedance is necessary for the stable operation of the
LDO. The amount of capacitance required to ensure
low source impedance will depend on the proximity of
the input source capacitors or battery type. For most
applications, 1 μF of capacitance will ensure stable
operation of the LDO circuit. For applications that have
load currents below 100 mA, the input capacitance
requirement can be lowered. The type of capacitor
used can be ceramic, tantalum or aluminum
electrolytic. The low ESR characteristics of the ceramic
will yield better noise and PSRR performance at high
frequency.
? 2007 Microchip Technology Inc.
相关PDF资料 |
PDF描述 |
|---|---|
| EEV-HB1V220P | CAP ALUM 22UF 35V 20% SMD |
| GCC50DREN-S734 | CONN EDGECARD 100PS .100 EYELET |
| MCP1700-2302E/TO | IC REG LDO 2.3V .2A TO-92-3 |
| GCC50DREH-S734 | CONN EDGECARD 100PS .100 EYELET |
| MCP1700-2202E/TO | IC REG LDO 2.2V .2A TO-92-3 |
相关代理商/技术参数 |
参数描述 |
|---|---|
| MCP1700-2802E/TO | 功能描述:低压差稳压器 - LDO 250mA CMOS LDO Isupp 1uA 2% Vout Acc RoHS:否 制造商:Texas Instruments 最大输入电压:36 V 输出电压:1.4 V to 20.5 V 回动电压（最大值）:307 mV 输出电流:1 A 负载调节:0.3 % 输出端数量: 输出类型:Fixed 最大工作温度:+ 125 C 安装风格:SMD/SMT 封装 / 箱体:VQFN-20 |
| MCP1700-3001E/TO | 功能描述:低压差稳压器 - LDO 250mA CMOS LDO Isupp 1uA 2% Vout Acc RoHS:否 制造商:Texas Instruments 最大输入电压:36 V 输出电压:1.4 V to 20.5 V 回动电压（最大值）:307 mV 输出电流:1 A 负载调节:0.3 % 输出端数量: 输出类型:Fixed 最大工作温度:+ 125 C 安装风格:SMD/SMT 封装 / 箱体:VQFN-20 |
| MCP1700-3002E/MB | 制造商:Microchip Technology Inc 功能描述: |
| MCP1700-3002E/TO | 功能描述:低压差稳压器 - LDO 250mA Adj LDO 2% RoHS:否 制造商:Texas Instruments 最大输入电压:36 V 输出电压:1.4 V to 20.5 V 回动电压（最大值）:307 mV 输出电流:1 A 负载调节:0.3 % 输出端数量: 输出类型:Fixed 最大工作温度:+ 125 C 安装风格:SMD/SMT 封装 / 箱体:VQFN-20 |
| MCP1700-3102E/TO | 功能描述:低压差稳压器 - LDO 250mA CMOS LDO Isupp 1uA 2% Vout Acc RoHS:否 制造商:Texas Instruments 最大输入电压:36 V 输出电压:1.4 V to 20.5 V 回动电压（最大值）:307 mV 输出电流:1 A 负载调节:0.3 % 输出端数量: 输出类型:Fixed 最大工作温度:+ 125 C 安装风格:SMD/SMT 封装 / 箱体:VQFN-20 |
发布紧急采购，3分钟左右您将得到回复。