参数资料
| 型号： | MCP1725T-1802E/MC |
| 厂商： | Microchip Technology |
| 文件页数： | 16/32页 |
| 文件大小： | 0K |
| 描述： | IC REG LDO 1.8V .5A 8DFN |
| 产品培训模块： | High Current LDOs |
| 标准包装： | 3,300 |
| 稳压器拓扑结构： | 正，固定式 |
| 输出电压： | 1.8V |
| 输入电压： | 2.3 V ~ 6 V |
| 电压 - 压降（标准）： | 0.21V @ 500mA |
| 稳压器数量： | 1 |
| 电流 - 输出： | 500mA（最小） |
| 工作温度： | -40°C ~ 125°C |
| 安装类型： | 表面贴装 |
| 封装/外壳： | 8-VFDFN 裸露焊盘 |
| 供应商设备封装： | 8-DFN（2x3） |
| 包装： | 带卷 (TR) |
第1页第2页第3页第4页第5页第6页第7页第8页第9页第10页第11页第12页第13页第14页第15页当前第16页第17页第18页第19页第20页第21页第22页第23页第24页第25页第26页第27页第28页第29页第30页第31页第32页
MCP1725
4.0
DEVICE OVERVIEW
EQUATION 4-2:
R 1 = R 2 ? -------------------------------- ?
? ?
The MCP1725 is a high output current, Low Dropout
(LDO) voltage regulator with an adjustable delay
power-good output and shutdown control input. The
Where:
V OUT – V ADJ
V ADJ
low dropout voltage of 210 mV typical at 0.5A of current
makes it ideal for battery-powered applications. Unlike
other high output current LDOs, the MCP1725 only
draws a maximum of 220 μA of quiescent current.
V OUT
V ADJ
=
=
LDO Output Voltage
ADJ Pin Voltage
(typically 0.41V)
4.1
LDO Output Voltage
4.2
Output Current and Current
The MCP1725 LDO is available with either a fixed
output voltage or an adjustable output voltage. The
output voltage range is 0.8V to 5.0V for both versions.
Limiting
The MCP1725 LDO is tested and ensured to supply a
minimum of 0.5A of output current. The MCP1725 has
4.1.1
ADJUST INPUT
no minimum output load, so the output load current can
go to 0 mA and the LDO will continue to regulate the
V OUT = V ADJ ? ------------------ ?
? ?
The adjustable version of the MCP1725 uses the ADJ
pin (pin 7) to get the output voltage feedback for output
voltage regulation. This allows the user to set the
output voltage of the device with two external resistors.
The nominal voltage for ADJ is 0.41V.
MCP1725. Resistors R 1 and R 2 form the resistor
divider network necessary to set the output voltage.
With this configuration, the equation for setting V OUT is:
EQUATION 4-1:
R 1 + R 2
R 2
Where:
output voltage to within tolerance.
The MCP1725 also incorporates an output current limit.
If the output voltage falls below 0.7V due to an overload
condition (usually represents a shorted load condition),
the output current is limited to 1.2A (typical). If the over-
load condition is a soft overload, the MCP1725 will
supply higher load currents of up to 1A. The MCP1725
should not be operated in this condition continuously as
it may result in failure of the device. However, this does
allow for device usage in applications that have higher
pulsed load currents having an average output current
value of 0.5A or less.
Output overload conditions may also result in an over-
temperature shutdown of the device. If the junction
temperature rises above 150°C, the LDO will shut
V OUT
=
LDO Output Voltage
V ADJ
=
ADJ Pin Voltage
for more information on
(typically 0.41V)
overtemperature shutdown.
4.3
Output Capacitor
V IN
MCP1725-ADJ
1 V IN V OUT 8
V OUT
The MCP1725 requires a minimum output capacitance
of 1 μF for output voltage stability. Ceramic capacitors
C 1
4.7 μF
2 V IN ADJ 7
3 SHDN C DELAY 6
R 1
C2
1 μF
are recommended because of their size, cost and
environmental robustness qualities.
O ff
On
4 GND
PWRGD 5
C 3
1000 pF
R 2
Aluminum-electrolytic and tantalum capacitors can be
used on the LDO output as well. The Equivalent Series
Resistance (ESR) of the electrolytic output capacitor
must be no greater than 1 ohm. The output capacitor
should be located as close to the LDO output as is
FIGURE 4-1:
Typical Adjustable Output
practical. Ceramic materials X7R and X5R have low
Voltage Application Circuit.
The allowable resistance value range for resistor R 2 is
from 10 k Ω to 200 k Ω . Solving the equation for R 1
yields the following equation:
DS22026B-page 16
temperature coefficients and are well within the
acceptable ESR range required. A typical 1 μF X7R
0805 capacitor has an ESR of 50 milli-ohms.
Larger LDO output capacitors can be used with the
MCP1725 to improve dynamic performance and power
supply ripple rejection performance. A maximum of
22 μF is recommended. Aluminum-electrolytic
capacitors are not recommended for low-temperature
applications of < -25°C.
? 2007 Microchip Technology Inc.
相关PDF资料 |
PDF描述 |
|---|---|
| AMC08DRYH-S734 | CONN EDGECARD 16POS DIP .100 SLD |
| RBC65DRTS-S13 | CONN EDGECARD 130PS .100 EXTEND |
| FMM12DSEH-S243 | CONN EDGECARD 24POS .156 EYELET |
| MCP1725T-1202E/MC | IC REG LDO 1.2V .5A 8DFN |
| RCC43DRTF-S13 | CONN EDGECARD 86POS .100 EXTEND |
相关代理商/技术参数 |
参数描述 |
|---|---|
| MCP1725T-2502E/MC | 功能描述:低压差稳压器 - LDO 500mA CMOS LDO Vout=2.5V RoHS:否 制造商:Texas Instruments 最大输入电压:36 V 输出电压:1.4 V to 20.5 V 回动电压（最大值）:307 mV 输出电流:1 A 负载调节:0.3 % 输出端数量: 输出类型:Fixed 最大工作温度:+ 125 C 安装风格:SMD/SMT 封装 / 箱体:VQFN-20 |
| MCP1725T-2502E/SN | 功能描述:低压差稳压器 - LDO 500mA CMOS LDO Vout=2.5V RoHS:否 制造商:Texas Instruments 最大输入电压:36 V 输出电压:1.4 V to 20.5 V 回动电压（最大值）:307 mV 输出电流:1 A 负载调节:0.3 % 输出端数量: 输出类型:Fixed 最大工作温度:+ 125 C 安装风格:SMD/SMT 封装 / 箱体:VQFN-20 |
| MCP1725T-3002E/MC | 功能描述:低压差稳压器 - LDO 500mA CMOS LDO Vout=3.0V RoHS:否 制造商:Texas Instruments 最大输入电压:36 V 输出电压:1.4 V to 20.5 V 回动电压（最大值）:307 mV 输出电流:1 A 负载调节:0.3 % 输出端数量: 输出类型:Fixed 最大工作温度:+ 125 C 安装风格:SMD/SMT 封装 / 箱体:VQFN-20 |
| MCP1725T-3002E/SN | 功能描述:低压差稳压器 - LDO 500mA CMOS LDO Vout=3.0V RoHS:否 制造商:Texas Instruments 最大输入电压:36 V 输出电压:1.4 V to 20.5 V 回动电压（最大值）:307 mV 输出电流:1 A 负载调节:0.3 % 输出端数量: 输出类型:Fixed 最大工作温度:+ 125 C 安装风格:SMD/SMT 封装 / 箱体:VQFN-20 |
| MCP1725T-3302E/MC | 功能描述:低压差稳压器 - LDO 500mA CMOS LDO Vout=3.3V RoHS:否 制造商:Texas Instruments 最大输入电压:36 V 输出电压:1.4 V to 20.5 V 回动电压（最大值）:307 mV 输出电流:1 A 负载调节:0.3 % 输出端数量: 输出类型:Fixed 最大工作温度:+ 125 C 安装风格:SMD/SMT 封装 / 箱体:VQFN-20 |
发布紧急采购，3分钟左右您将得到回复。