参数资料
| 型号： | MCP1725T-1802E/MC |
| 厂商： | Microchip Technology |
| 文件页数： | 17/32页 |
| 文件大小： | 0K |
| 描述： | IC REG LDO 1.8V .5A 8DFN |
| 产品培训模块： | High Current LDOs |
| 标准包装： | 3,300 |
| 稳压器拓扑结构： | 正，固定式 |
| 输出电压： | 1.8V |
| 输入电压： | 2.3 V ~ 6 V |
| 电压 - 压降（标准）： | 0.21V @ 500mA |
| 稳压器数量： | 1 |
| 电流 - 输出： | 500mA（最小） |
| 工作温度： | -40°C ~ 125°C |
| 安装类型： | 表面贴装 |
| 封装/外壳： | 8-VFDFN 裸露焊盘 |
| 供应商设备封装： | 8-DFN（2x3） |
| 包装： | 带卷 (TR) |
第1页第2页第3页第4页第5页第6页第7页第8页第9页第10页第11页第12页第13页第14页第15页第16页当前第17页第18页第19页第20页第21页第22页第23页第24页第25页第26页第27页第28页第29页第30页第31页第32页
MCP1725
4.4
Input Capacitor
The power good output is an open-drain output that can
Low input source impedance is necessary for the LDO
output to operate properly. When operating from
batteries, or in applications with long lead length
(> 10 inches) between the input source and the LDO,
some input capacitance is recommended. A minimum
of 1.0 μF to 4.7 μF is recommended for most
applications.
be pulled up to any voltage that is equal to or less than
the LDO input voltage. This output is capable of sinking
1.2 mA (V PWRGD < 0.4V maximum).
V PWRGD_TH
For applications that have output step load
requirements, the input capacitance of the LDO is very
important. The input capacitance provides the LDO
with a good local low-impedance source to pull the
transient currents from in order to respond quickly to
the output load step. For good step response
performance, the input capacitor should be of
equivalent (or higher) value than the output capacitor.
The capacitor should be placed as close to the input of
the LDO as is practical. Larger input capacitors will also
help reduce any high-frequency noise on the input and
V OUT
PWRGD
T PG
V OH
T VDET_PWRGD
V OL
output of the LDO and reduce the effects of any
inductance that exists between the input source
voltage and the input capacitance of the LDO.
FIGURE 4-2:
Power Good Timing.
4.5
Power Good Output (PWRGD)
V IN
T OR
The PWRGD output is used to indicate when the output
voltage of the LDO is within 92% (typical value, see
and Maximum specifications) of its nominal regulation
value.
As the output voltage of the LDO rises, the PWRGD
output will be held low until the output voltage has
exceeded the power good threshold plus the hysteresis
value. Once this threshold has been exceeded, the
power good time delay is started (shown as T PG in
good time delay is adjustable via the C DELAY pin of the
LDO (see Section 4.6 “C DELAY Input” ). By placing a
capacitor from the C DELAY pin to ground, the power
good time delay can be adjusted from 200 μs (no
capacitance) to 300 ms (0.1 μF capacitor). After the
time delay period, the PWRGD output will go high, indi-
cating that the output voltage is stable and within
regulation limits.
If the output voltage of the LDO falls below the power
good threshold, the power good output will transition
low. The power good circuitry has a 170 μs delay when
detecting a falling output voltage, which helps to
increase noise immunity of the power good output and
avoid false triggering of the power good output during
fast output transients. See Figure 4-2 for power good
timing characteristics.
When the LDO is put into Shutdown mode using the
SHDN input, the power good output is pulled low
immediately, indicating that the output voltage will be
out of regulation. The timing diagram for the power
good output when using the shutdown input is shown in
? 2007 Microchip Technology Inc.
30 μs
SHDN
V OUT
PWRGD
FIGURE 4-3:
Shutdown.
70 μs
T PG
Power Good Timing from
DS22026B-page 17
相关PDF资料 |
PDF描述 |
|---|---|
| AMC08DRYH-S734 | CONN EDGECARD 16POS DIP .100 SLD |
| RBC65DRTS-S13 | CONN EDGECARD 130PS .100 EXTEND |
| FMM12DSEH-S243 | CONN EDGECARD 24POS .156 EYELET |
| MCP1725T-1202E/MC | IC REG LDO 1.2V .5A 8DFN |
| RCC43DRTF-S13 | CONN EDGECARD 86POS .100 EXTEND |
相关代理商/技术参数 |
参数描述 |
|---|---|
| MCP1725T-2502E/MC | 功能描述:低压差稳压器 - LDO 500mA CMOS LDO Vout=2.5V RoHS:否 制造商:Texas Instruments 最大输入电压:36 V 输出电压:1.4 V to 20.5 V 回动电压（最大值）:307 mV 输出电流:1 A 负载调节:0.3 % 输出端数量: 输出类型:Fixed 最大工作温度:+ 125 C 安装风格:SMD/SMT 封装 / 箱体:VQFN-20 |
| MCP1725T-2502E/SN | 功能描述:低压差稳压器 - LDO 500mA CMOS LDO Vout=2.5V RoHS:否 制造商:Texas Instruments 最大输入电压:36 V 输出电压:1.4 V to 20.5 V 回动电压（最大值）:307 mV 输出电流:1 A 负载调节:0.3 % 输出端数量: 输出类型:Fixed 最大工作温度:+ 125 C 安装风格:SMD/SMT 封装 / 箱体:VQFN-20 |
| MCP1725T-3002E/MC | 功能描述:低压差稳压器 - LDO 500mA CMOS LDO Vout=3.0V RoHS:否 制造商:Texas Instruments 最大输入电压:36 V 输出电压:1.4 V to 20.5 V 回动电压（最大值）:307 mV 输出电流:1 A 负载调节:0.3 % 输出端数量: 输出类型:Fixed 最大工作温度:+ 125 C 安装风格:SMD/SMT 封装 / 箱体:VQFN-20 |
| MCP1725T-3002E/SN | 功能描述:低压差稳压器 - LDO 500mA CMOS LDO Vout=3.0V RoHS:否 制造商:Texas Instruments 最大输入电压:36 V 输出电压:1.4 V to 20.5 V 回动电压（最大值）:307 mV 输出电流:1 A 负载调节:0.3 % 输出端数量: 输出类型:Fixed 最大工作温度:+ 125 C 安装风格:SMD/SMT 封装 / 箱体:VQFN-20 |
| MCP1725T-3302E/MC | 功能描述:低压差稳压器 - LDO 500mA CMOS LDO Vout=3.3V RoHS:否 制造商:Texas Instruments 最大输入电压:36 V 输出电压:1.4 V to 20.5 V 回动电压（最大值）:307 mV 输出电流:1 A 负载调节:0.3 % 输出端数量: 输出类型:Fixed 最大工作温度:+ 125 C 安装风格:SMD/SMT 封装 / 箱体:VQFN-20 |
发布紧急采购，3分钟左右您将得到回复。