- 您现在的位置：买卖IC网 > PDF目录11599 > MCP2140A-I/SS (Microchip Technology)IC IRDA CONTROLLR DTE/DCE 20SSOP PDF资料下载
参数资料
| 型号： | MCP2140A-I/SS |
| 厂商： | Microchip Technology |
| 文件页数： | 53/66页 |
| 文件大小： | 0K |
| 描述： | IC IRDA CONTROLLR DTE/DCE 20SSOP |
| 标准包装： | 67 |
| 控制器类型： | IRDA 标准协议栈控制器 |
| 接口： | UART |
| 电源电压： | 3 V ~ 5.5 V |
| 电流 - 电源： | 2.2mA |
| 工作温度： | -40°C ~ 125°C |
| 安装类型： | 表面贴装 |
| 封装/外壳： | 20-SSOP（0.209"，5.30mm 宽） |
| 供应商设备封装： | 20-SSOP |
| 包装： | 管件 |
| 产品目录页面： | 685 (CN2011-ZH PDF) |
| 配用： | MCP2140DM-TMPSNS-ND - BOARD DEMO FOR MCP2140 |
第1页第2页第3页第4页第5页第6页第7页第8页第9页第10页第11页第12页第13页第14页第15页第16页第17页第18页第19页第20页第21页第22页第23页第24页第25页第26页第27页第28页第29页第30页第31页第32页第33页第34页第35页第36页第37页第38页第39页第40页第41页第42页第43页第44页第45页第46页第47页第48页第49页第50页第51页第52页当前第53页第54页第55页第56页第57页第58页第59页第60页第61页第62页第63页第64页第65页第66页
2007-2011 Microchip Technology Inc.
DS22050B-page 57
MCP2140A
C.1.2
IrLAP
The IrLAP protocol provides:
Management of communication processes on the
link between devices
A device-to-device connection for the reliable,
ordered transfer of data
Device discover procedures
Hidden node handling. 115.2 kbaud
Figure C-3 identifies the key parts and hierarchy of the
IrDA protocols. The bottom layer is the Physical layer,
IrPHY. This is the part that converts the serial data to
and from pulses of IR light. IR transceivers can’t trans-
mit and receive at the same time. The receiver has to
wait for the transmitter to finish sending. This is some-
times referred to as a “Half-Duplex” connection. The IR
Link Access Protocol (IrLAP) provides the structure for
packets (or “frames”) of data to emulate data that would
normally be free to stream back and forth.
FIGURE C-3:
IrDA STANDARD PROTOCOL
LAYERS
Figure C-4 shows how the IrLAP frame is organized.
The frame is preceded by some number of Beginning
of Frame characters (BOFs). The value of the BOF is
generally 0xC0, but 0xFF may be used if the last BOF
character is a 0xC0. The purpose of multiple BOFs is to
give the other station some warning that a frame is
coming.
The IrLAP frame begins with an address byte (“A”
field), then a control byte (“C” field). The control byte is
used to differentiate between different types of frames
and is also used to count frames. Frames can carry sta-
tus, data or commands. The IrLAP protocol has a com-
mand syntax of it’s own. These commands are part of
the control byte. Lastly, IrLAP frames carry data. This
data is the information (or “I”) field. The integrity of the
frame is ensured with a 16-bit CRC, referred to as the
Frame Check Sequence (FCS). The 16-bit CRC value
is transmitted LSB first. The end of the frame is marked
with an EOF character, which is always a 0xC1. The
frame structure described here is used for all versions
of IrDA protocols used for serial wire replacement for
speeds up to 115.2 kbaud.
FIGURE C-4:
IrLAP FRAME
In addition to defining the frame structure, IrLAP pro-
vides the “housekeeping” functions of opening, closing
and maintaining connections. The critical parameters
that determine the performance of the link are part of
this function. These parameters control how many
BOFs are used, identify the speed of the link, how fast
either party may change from receiving to transmitting,
etc. IrLAP has the responsibility of negotiating these
parameters to the highest common set so that both
sides can communicate as quickly and reliably as
possible.
Note:
Not supported by MCP2140A.
Host O.S. or Application
IrCOMM
IrLAP
IrPHY
Protocols
resident in
MCP2140A
IR pulses
transmitted
and
received
IrLMP – IAS
Note 1: The
MCP2140A
only
supports
communication baud rate of 9600 baud.
2: Another IrDA standard that is entering
into general usage is IR Object Exchange
(IrOBEX). This standard is not used for
serial connection emulation.
3: IrDA communication standards faster
than 115.2 kbaud use a different CRC
method and physical layer.
X BOFs BOF A C
FCS
I
EOF
(1+N) of C0h payload
2
bytes C1h
相关PDF资料 |
PDF描述 |
|---|---|
| MCP2515-I/ST | IC CAN CONTROLLER W/SPI 20TSSOP |
| PIC16LF1902-E/SP | MCU 3.5KB FLASH 128B RAM 28SPDIP |
| PIC16LF1825T-I/ML | MCU PIC 14KB FLASH 16-QFN |
| PIC16F720-E/P | MCU PIC 3.5KB FLASH 128B 20PDIP |
| MCP2515T-I/ML | IC CAN CTLR W/SPI 2.0B 20-QFN |
相关代理商/技术参数 |
参数描述 |
|---|---|
| MCP2140AT-I/P | 制造商:MICROCHIP 制造商全称:Microchip Technology 功能描述:IrDA㈢ Standard Protocol Stack Controller With Fixed 9600 Baud Communication Rate |
| MCP2140AT-I/SO | 功能描述:网络控制器与处理器 IC Enhanced MCP2140 Win Mobile 5.0 compatble RoHS:否 制造商:Micrel 产品:Controller Area Network (CAN) 收发器数量: 数据速率: 电源电流（最大值）:595 mA 最大工作温度:+ 85 C 安装风格:SMD/SMT 封装 / 箱体:PBGA-400 封装:Tray |
| MCP2140AT-I/SS | 功能描述:网络控制器与处理器 IC Enhanced MCP2140 Win Mobile 5.0 compatble RoHS:否 制造商:Micrel 产品:Controller Area Network (CAN) 收发器数量: 数据速率: 电源电流（最大值）:595 mA 最大工作温度:+ 85 C 安装风格:SMD/SMT 封装 / 箱体:PBGA-400 封装:Tray |
| MCP2140DM-TMPSNS | 功能描述:温度传感器开发工具 MCP2140 IrDA Wire- less Temp Demo RoHS:否 制造商:Texas Instruments 产品类型:Temperature Sensors and Control ICs 工具用于评估:MSP430G2553 接口类型:USB 工作电源电压: 工作电源电流: |
| MCP2140-I/P | 功能描述:网络控制器与处理器 IC 9600bd fixd spd IrDA RoHS:否 制造商:Micrel 产品:Controller Area Network (CAN) 收发器数量: 数据速率: 电源电流（最大值）:595 mA 最大工作温度:+ 85 C 安装风格:SMD/SMT 封装 / 箱体:PBGA-400 封装:Tray |
发布紧急采购，3分钟左右您将得到回复。