- 您现在的位置：买卖IC网 > PDF目录67986 > MCP23S09T-E/MG 8 I/O, PIA-GENERAL PURPOSE, PQCC16 PDF资料下载
参数资料
| 型号： | MCP23S09T-E/MG |
| 元件分类： | 微控制器/微处理器 |
| 英文描述： | 8 I/O, PIA-GENERAL PURPOSE, PQCC16 |
| 封装： | 3 X 3 MM, 0.90 MM HEIGHT, PLASTIC, QFN-16 |
| 文件页数： | 14/50页 |
| 文件大小： | 607K |
| 代理商： | MCP23S09T-E/MG |
第1页第2页第3页第4页第5页第6页第7页第8页第9页第10页第11页第12页第13页当前第14页第15页第16页第17页第18页第19页第20页第21页第22页第23页第24页第25页第26页第27页第28页第29页第30页第31页第32页第33页第34页第35页第36页第37页第38页第39页第40页第41页第42页第43页第44页第45页第46页第47页第48页第49页第50页
2009 Microchip Technology Inc.
DS22121B-page 21
MCP23009/MCP23S09
1.6.6
CONFIGURATION REGISTER
The Sequential Operation (SEQOP) controls the
incrementing function of the address pointer. If the
address pointer is disabled, the address pointer does
not automatically increment after each byte is clocked
during a serial transfer. This feature is useful when it is
desired to continuously poll (read) or modify (write) a
register.
The Open-Drain (ODR) control bit enables/disables the
INT pin for open-drain configuration.
The Interrupt Polarity (INTPOL) sets the polarity of the
INT pin. This bit is functional only when the ODR bit is
cleared, configuring the INT pin as active push-pull.
The Interrupt Clearing Control (INTCC) configures how
interrupts are cleared. When set (INTCC = 1), the
interrupt is cleared when the INTCAP register is read.
When cleared (INTCC = 0), the interrupt is cleared
when the GPIO register is read.
The interrupt can only be cleared when the interrupt
condition is inactive. Refer to Section 1.7.4 “Clearing
Interrupts” for details.
REGISTER 1-6:
IOCON – I/O EXPANDER CONFIGURATION REGISTER
U-0
R/W-0
U-0
R/W-0
-
SEQOP
-
ODR
INTPOL
INTCC
bit 7
bit 0
Legend:
R = Readable bit
W = Writable bit
U = Unimplemented bit, read as ‘0’
-n = Value at POR
‘1’ = Bit is set
‘0’ = Bit is cleared
x = Bit is unknown
bit 7
Unimplemented: Reads as 0
bit 6
Unimplemented: Reads as 0
bit 5
SEQOP: Sequential Operation mode bit.
1
= Sequential operation disabled, address pointer does not increment
0
= Sequential operation enabled, address pointer increments
bit 4
Unimplemented: Reads as 0
bit 3
Unimplemented: Reads as 0
bit 2
ODR: Configures the INT pin as an open-drain output.
1
= Open-drain output (overrides the INTPOL bit)
0
= Active driver output (INTPOL bit sets the polarity)
bit 1
INTPOL: Sets the polarity of the INT output pin.
1
= Active-high
0
= Active-low
bit 0
INTCC: Interrupt Clearing Control
1 = Reading INTCAP register clears the interrupt
0 = Reading GPIO register clears the interrupt
相关PDF资料 |
PDF描述 |
|---|---|
| MCP23009T-E/MG | 8 I/O, PIA-GENERAL PURPOSE, PQCC16 |
| MCP23016-I/ML | 16 I/O, PIA-GENERAL PURPOSE, PQCC28 |
| MCP23016-I/SS | 16 I/O, PIA-GENERAL PURPOSE, PDSO28 |
| MCP23016-I/SO | 16 I/O, PIA-GENERAL PURPOSE, PDSO28 |
| MCP23016-I/SP | 16 I/O, PIA-GENERAL PURPOSE, PDIP28 |
相关代理商/技术参数 |
参数描述 |
|---|---|
| MCP23S09TEP | 制造商:MICROCHIP 制造商全称:Microchip Technology 功能描述:8-Bit I/O Expander with Open-Drain Outputs |
| MCP23S09TESO | 制造商:MICROCHIP 制造商全称:Microchip Technology 功能描述:8-Bit I/O Expander with Open-Drain Outputs |
| MCP23S09TESS | 制造商:MICROCHIP 制造商全称:Microchip Technology 功能描述:8-Bit I/O Expander with Open-Drain Outputs |
| MCP23S17 | 制造商:MICROCHIP 制造商全称:Microchip Technology 功能描述:16-Bit I/O Expander with Serial Interface |
| MCP23S17-E/ML | 功能描述:接口-I/O扩展器 16bit Input/Output Exp SPI interface RoHS:否 制造商:NXP Semiconductors 逻辑系列: 输入/输出端数量: 最大工作频率:100 kHz 工作电源电压:1.65 V to 5.5 V 工作温度范围:- 40 C to + 85 C 安装风格:SMD/SMT 封装 / 箱体:HVQFN-16 封装:Reel |
发布紧急采购，3分钟左右您将得到回复。