- 您现在的位置：买卖IC网 > PDF目录67986 > MCP23S09T-E/MG 8 I/O, PIA-GENERAL PURPOSE, PQCC16 PDF资料下载
参数资料
| 型号： | MCP23S09T-E/MG |
| 元件分类： | 微控制器/微处理器 |
| 英文描述： | 8 I/O, PIA-GENERAL PURPOSE, PQCC16 |
| 封装： | 3 X 3 MM, 0.90 MM HEIGHT, PLASTIC, QFN-16 |
| 文件页数： | 48/50页 |
| 文件大小： | 607K |
| 代理商： | MCP23S09T-E/MG |
第1页第2页第3页第4页第5页第6页第7页第8页第9页第10页第11页第12页第13页第14页第15页第16页第17页第18页第19页第20页第21页第22页第23页第24页第25页第26页第27页第28页第29页第30页第31页第32页第33页第34页第35页第36页第37页第38页第39页第40页第41页第42页第43页第44页第45页第46页第47页当前第48页第49页第50页
2009 Microchip Technology Inc.
DS22121B-page 7
MCP23009/MCP23S09
1.3.3
SPI INTERFACE
The MCP23S09 operates in Mode 0,0 and Mode 1,1.
The difference between the two modes is the idle state
of the clock.
Mode 0,0: The idle state of the clock is LOW. Input data
is latched on the rising edge of the clock; output data is
driven on the falling edge of the clock.
Mode 1,1: The idle state of the clock is HIGH. Input
data is latched on the rising edge of the clock; output
data is driven on the falling edge of the clock.
1.3.3.1
SPI Write Operation
The SPI write operation is started by lowering CS. The
write command (slave address with R/W bit cleared) is
then clocked into the device. The opcode is followed by
an address and at least one data byte.
1.3.3.2
SPI Read Operation
The SPI read operation is started by lowering CS. The
SPI read command (slave address with R/W bit set) is
then clocked into the device. The opcode is followed by
an address, with at least one data byte being clocked
out of the device.
1.3.3.3
SPI Sequential Write/Read
For sequential operations, instead of deselecting the
device by raising CS, the master clocks the next byte
pointed to by the address pointer. (see Section 1.3.1
“Byte Mode and Sequential Mode” for details
regarding sequential operation control).
The sequence ends by the raising of CS.
The MCP23S09 address pointer will roll over to
address zero after reaching the last register address.
相关PDF资料 |
PDF描述 |
|---|---|
| MCP23009T-E/MG | 8 I/O, PIA-GENERAL PURPOSE, PQCC16 |
| MCP23016-I/ML | 16 I/O, PIA-GENERAL PURPOSE, PQCC28 |
| MCP23016-I/SS | 16 I/O, PIA-GENERAL PURPOSE, PDSO28 |
| MCP23016-I/SO | 16 I/O, PIA-GENERAL PURPOSE, PDSO28 |
| MCP23016-I/SP | 16 I/O, PIA-GENERAL PURPOSE, PDIP28 |
相关代理商/技术参数 |
参数描述 |
|---|---|
| MCP23S09TEP | 制造商:MICROCHIP 制造商全称:Microchip Technology 功能描述:8-Bit I/O Expander with Open-Drain Outputs |
| MCP23S09TESO | 制造商:MICROCHIP 制造商全称:Microchip Technology 功能描述:8-Bit I/O Expander with Open-Drain Outputs |
| MCP23S09TESS | 制造商:MICROCHIP 制造商全称:Microchip Technology 功能描述:8-Bit I/O Expander with Open-Drain Outputs |
| MCP23S17 | 制造商:MICROCHIP 制造商全称:Microchip Technology 功能描述:16-Bit I/O Expander with Serial Interface |
| MCP23S17-E/ML | 功能描述:接口-I/O扩展器 16bit Input/Output Exp SPI interface RoHS:否 制造商:NXP Semiconductors 逻辑系列: 输入/输出端数量: 最大工作频率:100 kHz 工作电源电压:1.65 V to 5.5 V 工作温度范围:- 40 C to + 85 C 安装风格:SMD/SMT 封装 / 箱体:HVQFN-16 封装:Reel |
发布紧急采购，3分钟左右您将得到回复。