- 您现在的位置：买卖IC网 > PDF目录9044 > MCP4725A1T-E/CH (Microchip Technology)IC DAC 12BIT EE W/I2C SOT23-6 PDF资料下载
参数资料
| 型号： | MCP4725A1T-E/CH |
| 厂商： | Microchip Technology |
| 文件页数： | 27/50页 |
| 文件大小： | 0K |
| 描述： | IC DAC 12BIT EE W/I2C SOT23-6 |
| 标准包装： | 1 |
| 设置时间： | 6µs |
| 位数： | 12 |
| 数据接口： | EEPROM，I²C，串行 |
| 转换器数目： | 1 |
| 电压电源： | 单电源 |
| 工作温度： | -40°C ~ 125°C |
| 安装类型： | 表面贴装 |
| 封装/外壳： | SOT-23-6 |
| 供应商设备封装： | SOT-23-6 |
| 包装： | 标准包装 |
| 输出数目和类型： | 1 电压，单极；1 电压，双极 |
| 采样率（每秒）： | * |
| 产品目录页面： | 673 (CN2011-ZH PDF) |
| 配用： | MCP4725DM-PTPLS-ND - BOARD DAUGHTER PICTAIL MCP4725 |
| 其它名称： | MCP4725A1T-E/CHDKR |
第1页第2页第3页第4页第5页第6页第7页第8页第9页第10页第11页第12页第13页第14页第15页第16页第17页第18页第19页第20页第21页第22页第23页第24页第25页第26页当前第27页第28页第29页第30页第31页第32页第33页第34页第35页第36页第37页第38页第39页第40页第41页第42页第43页第44页第45页第46页第47页第48页第49页第50页
2009 Microchip Technology Inc.
DS22039D-page 33
MCP4725
8.0
TYPICAL APPLICATIONS
The MCP4725 device is one of Microchip’s latest DAC
device family with non-volatile EEPROM memory. The
device is a general purpose resistive string DAC
intended to be used in applications where a precision,
and low power DAC with moderate bandwidth is
required.
Since the device includes non-volatile EEPROM
memory, the user can use this device for applications
that require the output to return to the previous set-up
value on subsequent power-ups.
Applications generally suited for the MCP4725 device
family include:
Set Point or Offset Trimming
Sensor Calibration
Portable Instrumentation (Battery Powered)
Motor Speed Control
8.1
Connecting to I2C BUS using
Pull-Up Resistors
The SCL and SDA pins of the MCP4725 are open-drain
configurations. These pins require a pull-up resistor as
shown in Figure 8-1. The value of these pull-up
resistors depends on the operating speed (standard,
fast, and high speed) and loading capacitance of the
I2C bus line. Higher value of pull-up resistor consumes
less power, but increases the signal transition time
(higher RC time constant) on the bus. Therefore, it can
limit the bus operating speed. The lower resistor value,
on the other hand, consumes higher power, but allows
higher operating speed. If the bus line has higher
capacitance due to long bus line or high number of
devices connected to the bus, a smaller pull-up resistor
is needed to compensate the long RC time constant.
The pull-up resistor is typically chosen between 1 k
and 10 k ranges for standard and fast modes, and
less than 1 k for high speed mode.
FIGURE 8-1:
I2C Bus Interface
Connection with A0 pin tied to VSS.
Two devices with the same A2 and A1 address bits can
be connected to the same I2C bus by utilizing the A0
address pin (Example: A0 pin of device A is tied to VDD,
and the other device’s pin is tied to VSS).
8.1.1
DEVICE CONNECTION TEST
The user can test the presence of the MCP4725 on the
I2C bus line without performing the data conversion.
This test can be achieved by checking an acknowledge
response from the MCP4725 after sending a read or
write command. Here is an example using Figure 8-2:
(a) Set the R/W bit “HIGH” in the address byte.
(b) If the MCP4725 is connected to the I2C bus line, it
will then acknowledge by pulling SDA bus LOW
during the ACK clock and then release the bus
back to the I2C Master.
(c) A STOP or repeated START bit can then be issued
from the Master and I2C communication can
continue.
FIGURE 8-2:
I2C Bus Connection Test.
MCP4725
VOUT A0
SCL
VSS
1
2
3
4
5
6
VDD SDA
10 F
0.1 F
R
Analog
VDD
To MCU
(MASTER)
Output
Note 1: R is the pull-up resistor. Typically
1 ~ 10 k
2: A0 can be tied to VSS, VDD or driven by
MCU
12 3 4
5 6 7
8
9
SCL
SDA
11 0
0A2 A1 A0 1
START
Bit
Address Byte
Address bits
Device bits
R/W
START
Bit
MCP4725
ACK
Response
相关PDF资料 |
PDF描述 |
|---|---|
| M83723/95A1404N | CONN PLUG 4POS STRAIGHT W/SCKT |
| VI-BTH-MY-F1 | CONVERTER MOD DC/DC 52V 50W |
| VI-BTF-MY-F4 | CONVERTER MOD DC/DC 72V 50W |
| MS27496E13B4P | CONN RCPT 4POS BOX MNT W/PINS |
| MCP4725A0T-E/CH | IC DAC 12BIT W/I2C SOT23A-6 |
相关代理商/技术参数 |
参数描述 |
|---|---|
| MCP4725A2T-E/CH | 功能描述:数模转换器- DAC Sngl 12-B NV DAC w/ I2C interface RoHS:否 制造商:Texas Instruments 转换器数量:1 DAC 输出端数量:1 转换速率:2 MSPs 分辨率:16 bit 接口类型:QSPI, SPI, Serial (3-Wire, Microwire) 稳定时间:1 us 最大工作温度:+ 85 C 安装风格:SMD/SMT 封装 / 箱体:SOIC-14 封装:Tube |
| MCP4725A2T-E/CH-CUT TAPE | 制造商:Microchip 功能描述:MCP4725 Series 1 Ch I2C EEPROM Memory 5.5 V 12-Bit D/A Converter SMT - SOT-23-6 |
| MCP4725A3T-E/CH | 功能描述:数模转换器- DAC Sngl 12-B NV DAC w/ I2C interface RoHS:否 制造商:Texas Instruments 转换器数量:1 DAC 输出端数量:1 转换速率:2 MSPs 分辨率:16 bit 接口类型:QSPI, SPI, Serial (3-Wire, Microwire) 稳定时间:1 us 最大工作温度:+ 85 C 安装风格:SMD/SMT 封装 / 箱体:SOIC-14 封装:Tube |
| MCP4725A3T-E/CH-CUT TAPE | 制造商:Microchip 功能描述:MCP4725 Series 1 Ch I2C EEPROM Memory 5.5 V 12-Bit D/A Converter SMT - SOT-23-6 |
| MCP4725DM-PTPLS | 功能描述:子卡和OEM板 MCP4725 DAC PICTail Plus Daughter Board RoHS:否 制造商:BeagleBoard by CircuitCo 产品:BeagleBone LCD4 Boards 用于:BeagleBone - BB-Bone - Open Source Development Kit |
发布紧急采购，3分钟左右您将得到回复。