- 您现在的位置：买卖IC网 > PDF目录16593 > MCZ33742SEGR2 (Freescale Semiconductor)IC SYSTEM BASIS CHIP CAN 28-SOIC PDF资料下载
参数资料
| 型号： | MCZ33742SEGR2 |
| 厂商： | Freescale Semiconductor |
| 文件页数： | 28/71页 |
| 文件大小： | 0K |
| 描述： | IC SYSTEM BASIS CHIP CAN 28-SOIC |
| 标准包装： | 1,000 |
| 应用： | 自动 |
| 电流 - 电源： | 42mA |
| 电源电压： | 5.5 V ~ 18 V |
| 工作温度： | -40°C ~ 125°C |
| 安装类型： | 表面贴装 |
| 封装/外壳： | 28-SOIC（0.295"，7.50mm 宽） |
| 供应商设备封装： | 28-SOIC W |
| 包装： | 带卷 (TR) |
第1页第2页第3页第4页第5页第6页第7页第8页第9页第10页第11页第12页第13页第14页第15页第16页第17页第18页第19页第20页第21页第22页第23页第24页第25页第26页第27页当前第28页第29页第30页第31页第32页第33页第34页第35页第36页第37页第38页第39页第40页第41页第42页第43页第44页第45页第46页第47页第48页第49页第50页第51页第52页第53页第54页第55页第56页第57页第58页第59页第60页第61页第62页第63页第64页第65页第66页第67页第68页第69页第70页第71页
Analog Integrated Circuit Device Data
34
Freescale Semiconductor
33742
FUNCTIONAL DEVICE OPERATION
OPERATIONAL MODES
DEBUG MODE: HARDWARE AND SOFTWARE DEBUG WITH THE 33742
When a SBC, and the MCU it serves, is used on the same printed circuit board, both the MCU software and the 33742
operation must be debugged concurrently. The following features permit system debugging by allowing the disabling of the SBC
internal software watchdog timer.
DEVICE POWER-UP, RESET PIN CONNECTED TO VDD
The VDD voltage is available when the 33742 power-up but the 33742 will not have received any SPI communication to
configure itself. Until set up by the system MCU, the 33742 will generate a reset every 350 ms until the part is configured. To
avoid continuous MCU hardware resets, the 33742’s RST pin can be connected directly to the VDD pin by a hardware jumper.
DEBUG MODES WITH SOFTWARE WATCHDOG DISABLED THOUGH SPI (NORMAL DEBUG, STANDBY
DEBUG, AND STOP DEBUG)
The software configurable watchdog can be disabled through the SPI. To set the watchdog disable while limiting the risk of
inadvertently disabling the watchdog timer during normal 33742 operation, it is recommended that the disable be done using the
following sequence:
Step 1–Power down the SBC.
Step 2–Power up the SBC. This sets the BATFAIL bit, allowing the 33742 to enter Normal Request mode.
Step 3–Write to the TIM1 sub register to allow the SBC to enter Normal mode.
Step 4–Write to the MCR register with data 0000. This enables the debug mode. Complete SPI byte is 0001 0000.
Step 5–Write to the MCR register normal debug. SPI byte is 0001 x101.
Important While in debug mode, the SBC can be used without having to clear the watchdog on a regular basis to facilitate
software and hardware debug.
Step 6–To leave the debug mode, write 0000 to the MCR register.
At Step 2, the SBC is in Normal Request. Steps 3, 4, and 5 should be completed consecutively and within the 350 ms time
period of the Normal Request mode. If not, the 33742 will go into Reset mode and enter Normal Request again.
Figure 15. Entering Debug Mode
When the SBC is operating in the debug mode and has been set into Stop Debug or Sleep mode, a wake-up causes the 33742
to enter the Normal Request mode for 350 ms. To avoid having the SBC generate an unwanted reset (enter Reset mode), the
next debug mode (Normal Debug or Standby Debug) should be configured within the 350 ms time window of the Normal Request
mode.
To avoid entering debug mode after a power-up, first read the BATFAIL bit (MCR read) and write 0000 into the MCR register.
Figures 16 and 17, page 35, show the detailed operation of the SBC once the debug mode has been selected.
VSUP
SPI
MCR (Step 4)
BATFAIL
VDD
Debug Mode
MCR (Step 5)
SPI: Read BATFAIL
MCR (Step 6)
33742 in Debug mode.
33742 not in Debug mode.
TIM1(Step 3)
No Watchdog
Watchdog ON
相关PDF资料 |
PDF描述 |
|---|---|
| H3AKH-3418G | IDC CABLE - HSC34H/AE34G/HPK34H |
| EVAL-AD5235SDZ | BOARD EVAL FOR AD5235 |
| MCZ33742EGR2 | IC SYSTEM BASIS CHIP CAN 28-SOIC |
| ECM30DCAN | CONN EDGECARD 60POS R/A .156 SLD |
| EVAL-ADCMP561BRQZ | BOARD EVALUATION ADCMP561BRQZ |
相关代理商/技术参数 |
参数描述 |
|---|---|
| MCZ33780EG | 功能描述:多路器开关 IC DBUS MASTER RoHS:否 制造商:Texas Instruments 通道数量:1 开关数量:4 开启电阻（最大值）:7 Ohms 开启时间（最大值）: 关闭时间（最大值）: 传播延迟时间:0.25 ns 工作电源电压:2.3 V to 3.6 V 工作电源电流: 最大工作温度:+ 85 C 安装风格:SMD/SMT 封装 / 箱体:UQFN-16 |
| MCZ33780EG | 制造商:Freescale Semiconductor 功能描述:DUAL DBUS MASTER INTERFACE 16SOIC |
| MCZ33780EGR2 | 功能描述:多路器开关 IC DBUS MASTER RoHS:否 制造商:Texas Instruments 通道数量:1 开关数量:4 开启电阻（最大值）:7 Ohms 开启时间（最大值）: 关闭时间（最大值）: 传播延迟时间:0.25 ns 工作电源电压:2.3 V to 3.6 V 工作电源电流: 最大工作温度:+ 85 C 安装风格:SMD/SMT 封装 / 箱体:UQFN-16 |
| MCZ33781EK | 功能描述:输入/输出控制器接口集成电路 DBUS2 MASTER STND RoHS:否 制造商:Silicon Labs 产品: 输入/输出端数量: 工作电源电压: 最大工作温度:+ 85 C 最小工作温度:- 40 C 安装风格:SMD/SMT 封装 / 箱体:QFN-64 封装:Tray |
| MCZ33781EKR2 | 功能描述:输入/输出控制器接口集成电路 DBUS2 MASTER STND RoHS:否 制造商:Silicon Labs 产品: 输入/输出端数量: 工作电源电压: 最大工作温度:+ 85 C 最小工作温度:- 40 C 安装风格:SMD/SMT 封装 / 箱体:QFN-64 封装:Tray |
发布紧急采购，3分钟左右您将得到回复。