参数资料
型号: MCZ34701EWR2
厂商: Freescale Semiconductor
文件页数: 19/39页
文件大小: 0K
描述: IC PWR SUPPLY 1.5A SW 32-SOIC
标准包装: 1,000
应用: 控制器,电源 QUICC? I、II
输入电压: 2.8 V ~ 6 V
输出数: 2
输出电压: 7.75V,0.8 V ~ 6 V
工作温度: -40°C ~ 85°C
安装类型: 表面贴装
封装/外壳: 32-SOIC(0.295",7.50mm 宽)
供应商设备封装: 32-SOIC
包装: 带卷 (TR)
FUNCTIONAL DESCRIPTION
FUNCTIONAL INTERNAL BLOCK DESCRIPTION
6.0 V
7.75V
Booster Output Voltage
Fault Timer
t FAULT = 10 ms
I pk Cu rrent Limit
0.5 I pk
t FAULT = 10 ms
Ip k
0.5 Ipk
Retry Timer
t Ret = 10 0 ms
0A
0V
Ipk = 1 A typ.
Booster Inductor Current
0 .6 A typ.
0.2 A typ.
0.1 A typ.
Figure 12. Boost Regulator Startup (Not To Scale)
SWITCHING REGULATOR
The switching regulator is a high frequency (300kHz
default, adjustable in the range from 200kHz to 400kHz),
synchronous buck converter driving integrated high side and
low side N-channel power MOSFETs. The switching
regulator output voltage is adjustable by means of an external
resistor divider to provide the required output voltage within
±2.0% accuracy, and is intended to directly power the core of
the microprocessor. The buck controller uses a PWM voltage
mode control topology with feed-forward to achieve excellent
line and load regulation.
The 34702 integrated boost regulator provides a 7.75V rail
which is used to properly bias the switcher’s MOSFET. In
addition, the boost structure has a very low start-up voltage
(Typically 1.6V), hence ensuring very low input voltage
functionality. A typical bootstrap technique is used to provide
voltage necessary to properly enhance the high side
MOSFET gate. When the regulator is supplied only from low
input voltage (e.g., single +3.3V supply rail), the bootstrap
capacitor is charged from the internal boost regulator output
V BST through an external diode. This arrangement allows
the 34701 to operate from very low input voltage and also
comply with the power sequencing requirements of the
supplied microcontroller.
Figure 13. Switching Regulator Current Limit
(Not To Scale)
To avoid destruction of the supplied circuits, the switching
regulator has a current limit with retry capability. When an
over-current condition occurs and the switch current reaches
the peak current limit value, the main (high side) switch is
turned off until the inductor current decays to the valley value,
which is one half of the peak current limit. If an over-current
condition exists for 10ms, the buck regulator control circuit
shuts the switcher OFF and the switcher retry timer starts to
time out. When the timer expires after 100ms, the switcher
engages the start-up sequence and runs for 10ms,
repeatedly checking for the over-current condition. Figure 13
describes the switching regulator over-current condition and
current limit. During the current limited operation (e.g., in
case of short-circuit on the switching regulator output), the
switching regulator operation is not synchronized to the
oscillator frequency. Figure 14 (respectively Figure 15 )
depicts the current limit with a retry capability feature of the
switcher (respectively LDO).
Figure 14. Switching Converter Over-current Protection
34701
Analog Integrated Circuit Device Data ?
Freescale Semiconductor
19
相关PDF资料
PDF描述
2256-08L POWER CHOKE 3.9UH MOLDED AXIAL
RBE35DHRT CONN CARD EXTEND 70POS 1MM
2256-07L POWER CHOKE 3.3UH MOLDED AXIAL
ACM25DRXH CONN EDGECARD 50POS DIP .156 SLD
GMC40DREN-S13 CONN EDGECARD 80POS .100 EXTEND
相关代理商/技术参数
参数描述
MCZ34702EW 功能描述:低压差稳压器 - LDO QUICCSUPPLY 2 RoHS:否 制造商:Texas Instruments 最大输入电压:36 V 输出电压:1.4 V to 20.5 V 回动电压(最大值):307 mV 输出电流:1 A 负载调节:0.3 % 输出端数量: 输出类型:Fixed 最大工作温度:+ 125 C 安装风格:SMD/SMT 封装 / 箱体:VQFN-20
MCZ34702EWR2 功能描述:低压差稳压器 - LDO QUICCSUPPLY 2 RoHS:否 制造商:Texas Instruments 最大输入电压:36 V 输出电压:1.4 V to 20.5 V 回动电压(最大值):307 mV 输出电流:1 A 负载调节:0.3 % 输出端数量: 输出类型:Fixed 最大工作温度:+ 125 C 安装风格:SMD/SMT 封装 / 箱体:VQFN-20
MCZ36304201 制造商:LG Corporation 功能描述:Duct
MCZ36305001 制造商:LG Corporation 功能描述:Duct
MCZ36444401 制造商:LG Corporation 功能描述:Duct