- 您现在的位置：买卖IC网 > PDF目录5181 > MCZ34701EWR2 (Freescale Semiconductor)IC PWR SUPPLY 1.5A SW 32-SOIC PDF资料下载
参数资料
| 型号： | MCZ34701EWR2 |
| 厂商： | Freescale Semiconductor |
| 文件页数： | 28/39页 |
| 文件大小： | 0K |
| 描述： | IC PWR SUPPLY 1.5A SW 32-SOIC |
| 标准包装： | 1,000 |
| 应用： | 控制器，电源 QUICC? I、II |
| 输入电压： | 2.8 V ~ 6 V |
| 输出数： | 2 |
| 输出电压： | 7.75V，0.8 V ~ 6 V |
| 工作温度： | -40°C ~ 85°C |
| 安装类型： | 表面贴装 |
| 封装/外壳： | 32-SOIC（0.295"，7.50mm 宽） |
| 供应商设备封装： | 32-SOIC |
| 包装： | 带卷 (TR) |
第1页第2页第3页第4页第5页第6页第7页第8页第9页第10页第11页第12页第13页第14页第15页第16页第17页第18页第19页第20页第21页第22页第23页第24页第25页第26页第27页当前第28页第29页第30页第31页第32页第33页第34页第35页第36页第37页第38页第39页
FUNCTIONAL DEVICE OPERATION
OPERATIONAL MODES
address acknowledge sent by 34702. I 2 C bus protocol
0 0 1 0 0 0 0 0 Ack 0 0 1 x x x x x
defines this circumstance as a master-transmitter and slave-
receiver configuration.
First Byte for Voltage Margining
Command Byte
Figure 27 illustrates a communication beginning with the
slave address, the first command for voltage margining, and
Figure 24. Voltage Margining Programming
(One Supply Only)
Note: x bits, which set the voltage margining value are
WATCHDOG PROGRAMMING OPERATION
For watchdog operation control, the master periodically
sends a watchdog first command followed by a command
byte selecting, or confirming, the watchdog period according
to the options listed in Table 8 . See Figure 25 for the
watchdog timer programming command example.
The internal watchdog timer is turned ON by receiving a
valid watchdog programming command (after receiving the
watchdog programming first command), and it is cleared
each time the next watchdog programming command is
written into the device, provided it arrives during the window
a third byte containing the address field 001 and the value
field 00101 corresponding with the LDO fifth setting (LDO
output voltage = +5% above its nominal value). If a
simultaneous setting for switcher is needed, a fourth byte
should be included before the STOP condition (P); for
instance, 001 11100 to set the switcher in its twelfth setting
(switcher output voltage = -5% below its nominal value) - see
The example of data transfer setting the watchdog timer is
S A6 A5 A4 A3 A2 A1 A0 0 Ack
START Write
Slave Address
open time. Thus, the watchdog programming command
0
1
1
0
0
0
0
0 Ack
clears the timer and sets the new timing conditions at the
same time. The watchdog programming first command
01100000 sent twice shuts the timer OFF, and the watchdog
First Command for Watchdog Programming
function is disabled. Any other valid watchdog command
turns the timer ON again.
0 1 1 0 1 0
Address Field Value Field:
0
1 Ac k P
STOP
Time-out WD = 320 ms
(Window OFF)
0 1 1 0 0 0 0 0 Ack 0 1 1 x x x x x
First Byte for Watchdog Programming Command Byte
Figure 25. Watchdog Timer Programming
Figure 26. Data Transfer Example - Watch Dog Timer
Setting.
S A6 A5 A4 A3 A2 A1 A0 0 Ack
Note: x bits, which set the watchdog timer value are
START
Slave Address
Write
Communication Stop
0
0
1
0
0
0
0
0 Ack
Only the master can terminate the data transfer by issuing
a STOP condition. The slave waits for this condition to
resume its initial state waiting for the next START condition
First Command for Voltage Margining
(see Figure 26 ).
0
0
1
0
0
1
0
1 Ac k P
COMPLETE DATA TRANSFER EXAMPLES
The master device controlling the I 2 C bus always starts
Address Field Value Field = LDO
5th Setting
STOP
addressing a 34701 slave IC in writing mode (R/W = 0) to
enable it to write a command byte just after receiving the
Figure 27. Data Transfer Example - LDO Voltage
Margining
34701
Analog Integrated Circuit Device Data ?
28
Freescale Semiconductor
相关PDF资料 |
PDF描述 |
|---|---|
| 2256-08L | POWER CHOKE 3.9UH MOLDED AXIAL |
| RBE35DHRT | CONN CARD EXTEND 70POS 1MM |
| 2256-07L | POWER CHOKE 3.3UH MOLDED AXIAL |
| ACM25DRXH | CONN EDGECARD 50POS DIP .156 SLD |
| GMC40DREN-S13 | CONN EDGECARD 80POS .100 EXTEND |
相关代理商/技术参数 |
参数描述 |
|---|---|
| MCZ34702EW | 功能描述:低压差稳压器 - LDO QUICCSUPPLY 2 RoHS:否 制造商:Texas Instruments 最大输入电压:36 V 输出电压:1.4 V to 20.5 V 回动电压（最大值）:307 mV 输出电流:1 A 负载调节:0.3 % 输出端数量: 输出类型:Fixed 最大工作温度:+ 125 C 安装风格:SMD/SMT 封装 / 箱体:VQFN-20 |
| MCZ34702EWR2 | 功能描述:低压差稳压器 - LDO QUICCSUPPLY 2 RoHS:否 制造商:Texas Instruments 最大输入电压:36 V 输出电压:1.4 V to 20.5 V 回动电压（最大值）:307 mV 输出电流:1 A 负载调节:0.3 % 输出端数量: 输出类型:Fixed 最大工作温度:+ 125 C 安装风格:SMD/SMT 封装 / 箱体:VQFN-20 |
| MCZ36304201 | 制造商:LG Corporation 功能描述:Duct |
| MCZ36305001 | 制造商:LG Corporation 功能描述:Duct |
| MCZ36444401 | 制造商:LG Corporation 功能描述:Duct |
发布紧急采购，3分钟左右您将得到回复。