参数资料
| 型号： | MIC3003GML TR |
| 厂商： | Micrel Inc |
| 文件页数： | 22/75页 |
| 文件大小： | 0K |
| 描述： | IC FOM MANAGEMENT W/CALIBR 24MLF |
| 标准包装： | 1,000 |
| 类型： | 激光二极管控制器（光纤） |
| 数据速率： | 10Gbps |
| 通道数： | 1 |
| 电源电压： | 3 V ~ 3.6 V |
| 电流 - 电源： | 2.3mA |
| 工作温度： | -40°C ~ 105°C |
| 封装/外壳： | 24-VFQFN 裸露焊盘，24-MLF? |
| 供应商设备封装： | 24-MLF?（4x4） |
| 包装： | 带卷 (TR) |
| 安装类型： | 表面贴装 |
第1页第2页第3页第4页第5页第6页第7页第8页第9页第10页第11页第12页第13页第14页第15页第16页第17页第18页第19页第20页第21页当前第22页第23页第24页第25页第26页第27页第28页第29页第30页第31页第32页第33页第34页第35页第36页第37页第38页第39页第40页第41页第42页第43页第44页第45页第46页第47页第48页第49页第50页第51页第52页第53页第54页第55页第56页第57页第58页第59页第60页第61页第62页第63页第64页第65页第66页第67页第68页第69页第70页第71页第72页第73页第74页第75页
Micrel, Inc.
Calibration Modes
The default mode of calibration in the MIC3003 is
external calibration, for which the INTCAL bit (bit 0 in
OEMCFG3 register) is set to 0. The internal calibration
mode is selected by setting INTCAL to 1.
A/ External Calibration
The voltage and temperature values returned by the
MIC3003’s A/D converter are internally calibrated. The
binary values of TEMPh:TEMPl and VOLTh:VOLTl are in
the format called for by SFF-8472 under Internal
Calibration.
SFF-8472 calls for a set of calibration constants to be
stored by the transceiver OEM at specific non-volatile
memory locations; refer to the SFF-8472 specifications
for the memory map of the calibration coefficients. The
MIC3003 provides the non-volatile memory required for
the storage of these constants. The Digital Diagnostic
Monitoring Interface specification should be consulted
for full details. Slopes and offsets are stored for use with
voltage, temperature, bias current, and transmitted
power measurements. Coefficients for a fourth-order
polynomial are provided for use with received power
measurements. The host system can retrieve these
constants and use them to process the measured data.
Voltage
The voltage values returned by the MIC3003’s A/D
converter are internally calibrated. The binary values of
VOLTh:VOLTl are in the format called for by SFF-8472
under Internal Calibration. Since VINh:VINl requires no
processing, the corresponding slope should be set to
one and the offset to zero.
Temperature
The temperature values returned by the MIC3003’s A/D
converter are internally calibrated. The binary values of
TEMPh:TEMPl are in the format called for by SFF-8472
under Internal Calibration.
The temperature value may be offset by storing a value
in A6:74(4Ah). The temperature offset is a six-bit signed
quantity with .5 degrees C resolution.
The temperature offset coefficient at A6:74(4Ah) is used
in the same way in both internal and external calibration
modes.
Bias Current
Bias current is sensed via an external sense resistor as
a voltage appearing between VILD+ and VILD-. The
value returned by the A/D is therefore a voltage
analogous to bias current. Bias current, IBIAS, is simply
V VILD /R SENSE . The binary value in IBIASh (IBIASl is
always zero) is related to bias current by:
MIC3003
(1)
The value of the least significant bit (LSB) of IBIASh is
given by:
(2)
Per SFF-8472, the value of the bias current LSB is 2μA.
The necessary conversion factor, “slope”, is therefore:
The tolerance of the sense resistor directly impacts the
accuracy of the bias current measurement. It is
recommended that the sense resistor chosen be 1%
accurate or better. The offset correction, if needed, can
be determined by shutting down the laser, i.e., asserting
TXDISABLE, and measuring the bias current. Any non-
zero result gives the offset required. The offset will be
equal and opposite to the result of the “zero current”
measurement.
TX Power
Transmit power is sensed via a resistor carrying the
monitor photodiode current. In most applications, the
signal at VMPD will be feedback voltage on FB. The
VMPD voltage may be measured relative to GND or
V DDA depending on the setting of the BIASREF bit in
OEMCFG1. The value returned by the A/D is therefore a
voltage analogous to transmit power. The binary value in
TXOPh (TXOPl is always zero) is related to transmit
power by:
(3)
For a given implementation, the value of R SENSE is
known. It is either the value of the external resistor or the
selected internal value of RFB. The constant, K, will
likely have to be determined through experimentation or
closed-loop calibration, as it depends on the monitoring
photodiode responsively and coupling efficiency.
It should be noted that the APC circuit acts to hold the
transmitted power constant. The value of transmit power
reported by the circuit should only vary by a small
amount as long as the APC is functioning correctly.
November 2009
22
M9999-111209-C
hbwhelp@micrel.com or (408) 955-1690
相关PDF资料 |
PDF描述 |
|---|---|
| MIC3172BN | IC REG BUCK BOOST INV CUK 8DIP |
| MIC33030-AYHJ TR | IC REG BUCK ADJ 0.4A 10HMLF |
| MIC33050-CYHL TR | IC REG BUCK SYNC 1V 0.6A 12MLF |
| MIC33153YHJ TR | IC REG BUCK SYNC ADJ 1.2A 14MLF |
| MIC35152WD TR | IC REG LDO ADJ 1.5A TO-252-5 |
相关代理商/技术参数 |
参数描述 |
|---|---|
| MIC3020BL | 功能描述:TOOL MINI CRIMPER FOR D SUB RoHS:否 类别:工具 >> 压接器，施用器，压力机 系列:Xcelite® 产品培训模块:Board-to-Wire Connectors 标准包装:1 系列:DF11 工具类型:台式压机，施用器 适用于相关产品:矩形触点，24-28 AWG 特点:- 配用:H1505TR-ND - CONN SOCKET 24-28AWG CRIMP GOLDH1504TR-ND - CONN SOCKET 24-28AWG CRIMP TIN 相关产品:AP105-DF11-2428S(64)-ND - TOOL APPLICATOR DF11 ACCESSORIESAP105-DF11-2428S(63)-ND - TOOL APPLICATOR DF11 ACCESSORIESAP105-DF11-2428S(62)-ND - TOOL APPLICATOR DF11 ACCESSORIESAP105-DF11-2428S(61)-ND - TOOL APPLICATOR DF11 ACCESSORIESCM-105 WITH TRANSFORMER-ND - TOOL AUTO CRIMPING MACHINE 其它名称:*AP105-DF11-2428SQ1139807AQ949366 |
| MIC-3042 | 制造商:ADVANTECH 制造商全称:Advantech Co., Ltd. 功能描述:4U CompactPCI? Enclosure with cPCI Power Supply (CT Bus or PICMG 2.16) |
| MIC-3042A-AE | 制造商:Advantech Co Ltd 功能描述:1U CHASSIS |
| MIC-3042AE | 制造商:ADVANTECH 制造商全称:Advantech Co., Ltd. 功能描述:4U CompactPCI? Enclosure with cPCI Power Supply (CT Bus or PICMG 2.16) |
| MIC-3042B-AE | 制造商:ADVANTECH 制造商全称:Advantech Co., Ltd. 功能描述:4U CompactPCI? Enclosure with cPCI Power Supply (CT Bus or PICMG 2.16) |
发布紧急采购，3分钟左右您将得到回复。