参数资料
型号: MIC3003GML TR
厂商: Micrel Inc
文件页数: 25/75页
文件大小: 0K
描述: IC FOM MANAGEMENT W/CALIBR 24MLF
标准包装: 1,000
类型: 激光二极管控制器(光纤)
数据速率: 10Gbps
通道数: 1
电源电压: 3 V ~ 3.6 V
电流 - 电源: 2.3mA
工作温度: -40°C ~ 105°C
封装/外壳: 24-VFQFN 裸露焊盘,24-MLF?
供应商设备封装: 24-MLF?(4x4)
包装: 带卷 (TR)
安装类型: 表面贴装
Micrel, Inc.
Figure 3. Internal Calibration RX Power Linear Approximation
C/ Reading the ADC Result Registers
The ADC result registers should be read as 16-bit
registers under internal calibration while under external
calibration they should be read as 8-bit or 16-bit
registers at the MSB address. For example, TX power
should be read under internal calibration as 16 bits at
address A2h: 66h–67h and under external calibration as
8 bits at address A2h: 66h. 9-bit temperature results and
12-bit receive power results should always be read as
16-bit quantities.
Reading the result registers using two-byte burst reads on
the SMBus guarantees that the two bytes are coherent
with each other—that is, they form a matched result pair.
If the two bytes were read separately, it is possible that
the internal result could be updated between the reads,
leading to an incorrect ADC result.
Figure 4. RXPOT Block Diagram
RXPOT
MIC3003
A programmable, non-volatile digitally controlled
potentiometer is provided for adjusting the gain of the
receive power measurement signal chain in the analog
domain. Five bits in the RXPOT register are used to set
and adjust the position of potentiometer. RXPOT
functions as a programmable divider or attenuator. It is
adjustable in steps from 1:1 (no divider action) down to
1/32 in steps of 1/32. If RXPOT is set to zero, then the
divider is bypassed completely. There will be no scaling
of the input signal, and the resistor network will be
disconnected from the VRX pin. At all other settings of
RXPOT, there will be a 32k ? (typical) load seen on
VRX.
Laser Diode Bias Control
The MIC3003 can be configured to generate a constant
bias current using electrical feedback, or regulate
average transmitted optical power using a feedback
signal from a monitor photodiode, as shown in Figure 5.
An operational amplifier is used to control laser bias
current via the V BIAS output. The VBIAS pin can drive a
maximum of ±10mA. An external bipolar transistor
provides current gain. The polarity of the op amp’s
output is programmable with BIASREF (bit-5 in
OEMCFG1) in order to accommodate either NPN or
PNP transistors that drive common anode and common
cathode laser, respectively. Additionally, the polarity of
the feedback signal is programmable for use with either
common-emitter or emitter-follower transistor circuits.
November 2009
25
M9999-111209-C
hbwhelp@micrel.com or (408) 955-1690
相关PDF资料
PDF描述
MIC3172BN IC REG BUCK BOOST INV CUK 8DIP
MIC33030-AYHJ TR IC REG BUCK ADJ 0.4A 10HMLF
MIC33050-CYHL TR IC REG BUCK SYNC 1V 0.6A 12MLF
MIC33153YHJ TR IC REG BUCK SYNC ADJ 1.2A 14MLF
MIC35152WD TR IC REG LDO ADJ 1.5A TO-252-5
相关代理商/技术参数
参数描述
MIC3020BL 功能描述:TOOL MINI CRIMPER FOR D SUB RoHS:否 类别:工具 >> 压接器,施用器,压力机 系列:Xcelite® 产品培训模块:Board-to-Wire Connectors 标准包装:1 系列:DF11 工具类型:台式压机,施用器 适用于相关产品:矩形触点,24-28 AWG 特点:- 配用:H1505TR-ND - CONN SOCKET 24-28AWG CRIMP GOLDH1504TR-ND - CONN SOCKET 24-28AWG CRIMP TIN 相关产品:AP105-DF11-2428S(64)-ND - TOOL APPLICATOR DF11 ACCESSORIESAP105-DF11-2428S(63)-ND - TOOL APPLICATOR DF11 ACCESSORIESAP105-DF11-2428S(62)-ND - TOOL APPLICATOR DF11 ACCESSORIESAP105-DF11-2428S(61)-ND - TOOL APPLICATOR DF11 ACCESSORIESCM-105 WITH TRANSFORMER-ND - TOOL AUTO CRIMPING MACHINE 其它名称:*AP105-DF11-2428SQ1139807AQ949366
MIC-3042 制造商:ADVANTECH 制造商全称:Advantech Co., Ltd. 功能描述:4U CompactPCI? Enclosure with cPCI Power Supply (CT Bus or PICMG 2.16)
MIC-3042A-AE 制造商:Advantech Co Ltd 功能描述:1U CHASSIS
MIC-3042AE 制造商:ADVANTECH 制造商全称:Advantech Co., Ltd. 功能描述:4U CompactPCI? Enclosure with cPCI Power Supply (CT Bus or PICMG 2.16)
MIC-3042B-AE 制造商:ADVANTECH 制造商全称:Advantech Co., Ltd. 功能描述:4U CompactPCI? Enclosure with cPCI Power Supply (CT Bus or PICMG 2.16)