参数资料
| 型号： | MIC3003GML TR |
| 厂商： | Micrel Inc |
| 文件页数： | 39/75页 |
| 文件大小： | 0K |
| 描述： | IC FOM MANAGEMENT W/CALIBR 24MLF |
| 标准包装： | 1,000 |
| 类型： | 激光二极管控制器（光纤） |
| 数据速率： | 10Gbps |
| 通道数： | 1 |
| 电源电压： | 3 V ~ 3.6 V |
| 电流 - 电源： | 2.3mA |
| 工作温度： | -40°C ~ 105°C |
| 封装/外壳： | 24-VFQFN 裸露焊盘，24-MLF? |
| 供应商设备封装： | 24-MLF?（4x4） |
| 包装： | 带卷 (TR) |
| 安装类型： | 表面贴装 |
第1页第2页第3页第4页第5页第6页第7页第8页第9页第10页第11页第12页第13页第14页第15页第16页第17页第18页第19页第20页第21页第22页第23页第24页第25页第26页第27页第28页第29页第30页第31页第32页第33页第34页第35页第36页第37页第38页当前第39页第40页第41页第42页第43页第44页第45页第46页第47页第48页第49页第50页第51页第52页第53页第54页第55页第56页第57页第58页第59页第60页第61页第62页第63页第64页第65页第66页第67页第68页第69页第70页第71页第72页第73页第74页第75页
Micrel, Inc.
Figure 24. Eight-Byte Block Write Protocol
MIC3003
Acknowledge Polling
The MIC3003’s non-volatile memory cannot be accessed
during the internal memory update. To allow for maximum
speed bulk writes, the MIC3003 supports acknowledge
polling. The MIC3003 will not acknowledge serial bus
transactions while internal writes are in progress. The
host may therefore monitor for the end of the write
process by periodically checking for an
acknowledgement. The longest duration for the internal
memory update to complete for a block write is
approximately 26 ms.
Write Protection and Data Security
OEM Password
A password is required to access the OEM areas of the
MIC3003, specifically the non-volatile memory, look-up
tables, and registers at serial addresses A4 h and A6 h . A
four-byte field, OEMPWSET, at serial address A6 h is
used for setting the OEM password. The OEM password
is set by writing OEMPWSET with the new value. The
password comparison is performed following the write to
the MSB of the OEMPW, address 7B h (or 7E h if
OEMCFG5 bit 2 is set to 1) at serial address A2 h .
Therefore, this byte must be written last. A four-byte
burst-write sequence to address 78 h (or 7B h if OEMCFG5
bit 2 is set to 1) may be used as this will result in the
MSbyte being written last. New passwords written to the
OEMPWSET registers will not take effect until after a
power-on reset occurs or a warm reset is performed using
the RST bit in OEMCFG0. This allows the new password
to be verified before it takes effect.
The corresponding four-byte field for password entry,
OEMPW, is located at serial address A2 h . This field is
therefore always visible to the host system. OEMPW is
compared to the four-byte OEMPWSET field at serial
address A6 h . If the two fields match, access is allowed to
the OEM areas of the MIC3003 non-volatile memory at
serial addresses A4 h and A6 h . If OEMPWSET is all zeroes,
no password security will exist. The value in OEMPW will
be ignored. This helps prevent a deliberately unsecured
MIC3003 from being inadvertently locked. Once a valid
password is entered, the MIC3003 OEM areas will be
accessible. The OEM areas may be re-secured by writing
an incorrect password value at OEMPW, e.g., all zeroes. In
all cases, OEMPW must be written LSB first through MSB
last. The OEM areas will be inaccessible following the final
write operation to OEMPW’s LSB. The OEMPW field is
reset to all zeros at power on. Any values written to these
locations will be readable by the host regardless of the
locked/unlocked status of the device. If OEMPWSET is set
to zero (00000000 h ), the MIC3003 will remain unlocked
regardless of the contents of the OEMPW field. This is the
factory default security setting.
Note that a valid OEM password allows access to the OEM
and user areas of the chip, i.e., the entire memory map.
OEM Mode and User Mode
When the OEM password is unlocked (either by matching
the set password or if the password is all zeros), the
MIC3003 is in OEM Mode. If the part is locked, the part is in
User Mode.
November 2009
39
M9999-111209-C
hbwhelp@micrel.com or (408) 955-1690
相关PDF资料 |
PDF描述 |
|---|---|
| MIC3172BN | IC REG BUCK BOOST INV CUK 8DIP |
| MIC33030-AYHJ TR | IC REG BUCK ADJ 0.4A 10HMLF |
| MIC33050-CYHL TR | IC REG BUCK SYNC 1V 0.6A 12MLF |
| MIC33153YHJ TR | IC REG BUCK SYNC ADJ 1.2A 14MLF |
| MIC35152WD TR | IC REG LDO ADJ 1.5A TO-252-5 |
相关代理商/技术参数 |
参数描述 |
|---|---|
| MIC3020BL | 功能描述:TOOL MINI CRIMPER FOR D SUB RoHS:否 类别:工具 >> 压接器，施用器，压力机 系列:Xcelite® 产品培训模块:Board-to-Wire Connectors 标准包装:1 系列:DF11 工具类型:台式压机，施用器 适用于相关产品:矩形触点，24-28 AWG 特点:- 配用:H1505TR-ND - CONN SOCKET 24-28AWG CRIMP GOLDH1504TR-ND - CONN SOCKET 24-28AWG CRIMP TIN 相关产品:AP105-DF11-2428S(64)-ND - TOOL APPLICATOR DF11 ACCESSORIESAP105-DF11-2428S(63)-ND - TOOL APPLICATOR DF11 ACCESSORIESAP105-DF11-2428S(62)-ND - TOOL APPLICATOR DF11 ACCESSORIESAP105-DF11-2428S(61)-ND - TOOL APPLICATOR DF11 ACCESSORIESCM-105 WITH TRANSFORMER-ND - TOOL AUTO CRIMPING MACHINE 其它名称:*AP105-DF11-2428SQ1139807AQ949366 |
| MIC-3042 | 制造商:ADVANTECH 制造商全称:Advantech Co., Ltd. 功能描述:4U CompactPCI? Enclosure with cPCI Power Supply (CT Bus or PICMG 2.16) |
| MIC-3042A-AE | 制造商:Advantech Co Ltd 功能描述:1U CHASSIS |
| MIC-3042AE | 制造商:ADVANTECH 制造商全称:Advantech Co., Ltd. 功能描述:4U CompactPCI? Enclosure with cPCI Power Supply (CT Bus or PICMG 2.16) |
| MIC-3042B-AE | 制造商:ADVANTECH 制造商全称:Advantech Co., Ltd. 功能描述:4U CompactPCI? Enclosure with cPCI Power Supply (CT Bus or PICMG 2.16) |
发布紧急采购，3分钟左右您将得到回复。