- 您现在的位置：买卖IC网 > PDF目录262872 > MSC1210Y4PAGR (TEXAS INSTRUMENTS INC) 8-BIT, FLASH, 33 MHz, MICROCONTROLLER, PQFP64 PDF资料下载
参数资料
| 型号： | MSC1210Y4PAGR |
| 厂商： | TEXAS INSTRUMENTS INC |
| 元件分类： | 微控制器/微处理器 |
| 英文描述： | 8-BIT, FLASH, 33 MHz, MICROCONTROLLER, PQFP64 |
| 封装： | GREEN, PLASTIC, TQFP-64 |
| 文件页数： | 20/94页 |
| 文件大小： | 913K |
| 代理商： | MSC1210Y4PAGR |
第1页第2页第3页第4页第5页第6页第7页第8页第9页第10页第11页第12页第13页第14页第15页第16页第17页第18页第19页当前第20页第21页第22页第23页第24页第25页第26页第27页第28页第29页第30页第31页第32页第33页第34页第35页第36页第37页第38页第39页第40页第41页第42页第43页第44页第45页第46页第47页第48页第49页第50页第51页第52页第53页第54页第55页第56页第57页第58页第59页第60页第61页第62页第63页第64页第65页第66页第67页第68页第69页第70页第71页第72页第73页第74页第75页第76页第77页第78页第79页第80页第81页第82页第83页第84页第85页第86页第87页第88页第89页第90页第91页第92页第93页第94页
MSC1210
SBAS203J MARCH 2002 REVISED JANUARY 2008
www.ti.com
27
RESET
The device can be reset from the following sources:
D Power-on reset
D External reset
D Software reset
D Watchdog timer reset
D Brownout reset
An external reset is accomplished by taking the RST pin
high for two tOSC periods, followed by taking the RST pin
low. A software reset is accomplished through the System
Reset register (SRTST, 0F7h). A watchdog timer reset is
enabled and controlled through Hardware Configuration
Register 0 (HCR0) and the Watchdog Timer register
(WDTCON, 0FFh). A brownout reset is enabled through
Hardware Configuration Register 1 (HCR1). External
reset, software reset, and watchdog timer reset complete
after 217 clock cycles. A brownout reset completes after 215
clock cycles.
All sources of reset cause the digital pins to be pulled high
from the initiation of the reset. For an external reset, taking
the RST pin high stops device operation, crystal
oscillation, and causes all digital pins to be pulled high from
that point. Taking the RST pin low initiates the reset
procedure.
A recommended external reset circuit is shown in
Figure 17. The serial 10k
resistor is recommended for
any external reset circuit configuration.
10k
13
RST
MSC1210
0.1
F
1M
DV
DD
Figure 17. Typical Reset Circuit
POWER-ON RESET
The on-chip power-on reset (POR) circuitry releases the
device from reset at approximately DVDD = 2.0V. The POR
accommodates power-supply ramp rates as slow as
1V/10ms. To ensure proper operation, the power supply
should ramp monotonically. Note that as the device is
released from reset and program execution begins, the
device current consumption may increase, which may
result in a power-supply voltage drop. If the power supply
ramps at a slower rate, is not monotonic, or a brownout
condition occurs (where the supply does not drop below
the 2.0V threshold), then improper device operation may
occur. The on-chip brownout reset may provide benefit in
these conditions.
BROWNOUT RESET
The brownout reset (BOR) is enabled through Hardware
Configuration Register 1 (HCR1). If the conditions for
proper POR are not met or the device encounters a
brownout condition that does not generate a POR, the
BOR can be used to ensure proper device operation. The
BOR will hold the state of the device when the power
supply drops below the threshold level programmed in
HCR1, and then generate a reset when the supply rises
above the threshold level. Note that as the device is
released from reset, and program execution begins, the
device current consumption may increase, which may
result in a power-supply voltage drop, which may initiate
another brownout condition.
The BOR level should be chosen to match closely with the
application. For example, with a high external clock
frequency, the BOR level should match the minimum
operating voltage range for the device, or improper
operation may still occur.
Note that AVDD must rise above 2.0V for the Analog
Brownout Reset function to be disabled; otherwise, it will
be enabled and hold the device in reset.
The BOR voltage is not calibrated until the end of the reset
cycle; therefore, the actual BOR voltage will be
approxiamtely 25% higher than the selected voltage. This
can create a condition where the reset never ends (for
example, when selecting a 4.5V BOR voltage for a 5V
power supply).
相关PDF资料 |
PDF描述 |
|---|---|
| M38503M4A-XXXFP | 8-BIT, MROM, 12.5 MHz, MICROCONTROLLER, PDSO42 |
| M38K27M4-XXXFP | 8-BIT, MROM, 8 MHz, MICROCONTROLLER, PQFP64 |
| M30101M2-XXXFP | 16-BIT, MROM, 16 MHz, MICROCONTROLLER, PDSO42 |
| MSP430F437IPZR | 16-BIT, FLASH, 8 MHz, RISC MICROCONTROLLER, PQFP100 |
| MC68HC05CC1B | 8-BIT, MROM, 4.2 MHz, MICROCONTROLLER, PDIP42 |
相关代理商/技术参数 |
参数描述 |
|---|---|
| MSC1210Y4PAGRG4 | 功能描述:模数转换器 - ADC Prec ADC w/ 8051 Mcntrl & Flash RoHS:否 制造商:Texas Instruments 通道数量:2 结构:Sigma-Delta 转换速率:125 SPs to 8 KSPs 分辨率:24 bit 输入类型:Differential 信噪比:107 dB 接口类型:SPI 工作电源电压:1.7 V to 3.6 V, 2.7 V to 5.25 V 最大工作温度:+ 85 C 安装风格:SMD/SMT 封装 / 箱体:VQFN-32 |
| MSC1210Y4PAGT | 功能描述:模数转换器 - ADC Prec ADC w/ 8051 Mcntrl & Flash RoHS:否 制造商:Texas Instruments 通道数量:2 结构:Sigma-Delta 转换速率:125 SPs to 8 KSPs 分辨率:24 bit 输入类型:Differential 信噪比:107 dB 接口类型:SPI 工作电源电压:1.7 V to 3.6 V, 2.7 V to 5.25 V 最大工作温度:+ 85 C 安装风格:SMD/SMT 封装 / 箱体:VQFN-32 |
| MSC1210Y4PAGTG4 | 功能描述:模数转换器 - ADC Prec ADC w/ 8051 Mcntrl & Flash RoHS:否 制造商:Texas Instruments 通道数量:2 结构:Sigma-Delta 转换速率:125 SPs to 8 KSPs 分辨率:24 bit 输入类型:Differential 信噪比:107 dB 接口类型:SPI 工作电源电压:1.7 V to 3.6 V, 2.7 V to 5.25 V 最大工作温度:+ 85 C 安装风格:SMD/SMT 封装 / 箱体:VQFN-32 |
| MSC1210Y5 | 制造商:TI 制造商全称:Texas Instruments 功能描述:Precision Analog-to-Digital Converter (ADC) with 8051 Microcontroller and Flash Memory |
| MSC1210Y5PAGR | 功能描述:模数转换器 - ADC Prec ADC w/ 8051 Mcntrl & Flash RoHS:否 制造商:Texas Instruments 通道数量:2 结构:Sigma-Delta 转换速率:125 SPs to 8 KSPs 分辨率:24 bit 输入类型:Differential 信噪比:107 dB 接口类型:SPI 工作电源电压:1.7 V to 3.6 V, 2.7 V to 5.25 V 最大工作温度:+ 85 C 安装风格:SMD/SMT 封装 / 箱体:VQFN-32 |
发布紧急采购，3分钟左右您将得到回复。