- 您现在的位置：买卖IC网 > PDF目录96086 > MSD1819A-RT3 (ON SEMICONDUCTOR) 100 mA, 50 V, NPN, Si, SMALL SIGNAL TRANSISTOR PDF资料下载
参数资料
| 型号： | MSD1819A-RT3 |
| 厂商： | ON SEMICONDUCTOR |
| 元件分类： | 小信号晶体管 |
| 英文描述： | 100 mA, 50 V, NPN, Si, SMALL SIGNAL TRANSISTOR |
| 封装： | CASE 419-04, SC-70, 3 PIN |
| 文件页数： | 4/5页 |
| 文件大小： | 153K |
| 代理商： | MSD1819A-RT3 |
MSD1819ART1
http://onsemi.com
1376
PD =
TJ(max) TA
R
θJA
PD =
150
°C 25°C
0.625
°C/W
= 200 milliwatts
The soldering temperature and time should not exceed
260
°C for more than 10 seconds.
When shifting from preheating to soldering, the
maximum temperature gradient should be 5
°C or less.
After soldering has been completed, the device should
be allowed to cool naturally for at least three minutes.
Gradual cooling should be used as the use of forced
cooling will increase the temperature gradient and
result in latent failure due to mechanical stress.
Mechanical stress or shock should not be applied dur-
ing cooling
* Soldering a device without preheating can cause exces-
sive thermal shock and stress which can result in damage
to the device.
INFORMATION FOR USING THE SC70/SOT323 SURFACE MOUNT PACKAGE
MINIMUM RECOMMENDED FOOTPRINT FOR SURFACE MOUNTED APPLICATIONS
Surface mount board layout is a critical portion of the total
design. The footprint for the semiconductor packages must
be the correct size to insure proper solder connection
SC70/SOT323 POWER DISSIPATION
The power dissipation of the SC70/SOT323 is a func-
tion of the pad size. This can vary from the minimum pad
size for soldering to the pad size given for maximum power
dissipation. Power dissipation for a surface mount device
is determined by TJ(max), the maximum rated junction tem-
perature of the die, R
θJA, the thermal resistance from the
device junction to ambient; and the operating temperature,
TA. Using the values provided on the data sheet, PD can be
calculated as follows.
The values for the equation are found in the maximum
ratings table on the data sheet. Substituting these values into
the equation for an ambient temperature TA of 25°C, one
can calculate the power dissipation of the device which in
this case is 200 milliwatts.
The 0.625
°C/W assumes the use of the recommended
footprint on a glass epoxy printed circuit board to achieve
a power dissipation of 200 milliwatts. Another alternative
would be to use a ceramic substrate or an aluminum core
board such as Thermal Clad
. Using a board material such
as Thermal Clad, a higher power dissipation of 300 milli-
watts can be achieved using the same footprint.
interface between the board and the package. With the
correct pad geometry, the packages will self align when
subjected to a solder reflow process.
SOLDERING PRECAUTIONS
The melting temperature of solder is higher than the rated
temperature of the device. When the entire device is heated
to a high temperature, failure to complete soldering within
a short time could result in device failure. Therefore, the
following items should always be observed in order to
minimize the thermal stress to which the devices are
subjected.
Always preheat the device.
The delta temperature between the preheat and
soldering should be 100
°C or less.*
When preheating and soldering, the temperature of the
leads and the case must not exceed the maximum
temperature ratings as shown on the data sheet. When
using infrared heating with the reflow soldering
method, the difference should be a maximum of 10
°C.
mm
inches
0.035
0.9
0.075
0.7
1.9
0.028
0.65
0.025
0.65
0.025
相关PDF资料 |
PDF描述 |
|---|---|
| MSD42T1G | 150 mA, 300 V, NPN, Si, SMALL SIGNAL TRANSISTOR |
| MSD52-16 | 3 PHASE, 1600 V, SILICON, BRIDGE RECTIFIER DIODE |
| MSD52-16 | 3 PHASE, 1600 V, SILICON, BRIDGE RECTIFIER DIODE |
| MSD601-RT3 | 100 mA, 25 V, NPN, Si, SMALL SIGNAL TRANSISTOR |
| MSD601-ST3 | 100 mA, 25 V, NPN, Si, SMALL SIGNAL TRANSISTOR |
相关代理商/技术参数 |
参数描述 |
|---|---|
| MSD1819A-ST1 | 制造商:MOTOROLA 制造商全称:Motorola, Inc 功能描述:NPN GENERAL PURPOSE AMPLIFIER TRANSISTORS SURFACE MOUNT |
| MSD-1G | 制造商:JVC Worldwide 功能描述:1G MICRO SDCARD |
| MSD-1G-NP | 制造商:JVC Worldwide 功能描述:1G MICRO SDCARD |
| MSD200 | 制造商:MICROSEMI 制造商全称:Microsemi Corporation 功能描述:Glass Passivated Three Phase Rectifier Bridge |
| MSD200-08 | 功能描述:DIODE BRIDGE 3PH 800V 200A SM3 RoHS:是 类别:半导体模块 >> 桥式整流器 系列:- 标准包装:10 系列:- 电压 - 峰值反向(最大):1000V 电流 - DC 正向(If):35A 二极管类型:单相 速度:标准恢复 >500ns，> 200mA（Io） 反向恢复时间(trr):- 安装类型:底座安装 封装/外壳:ISOTOP 包装:托盘 供应商设备封装:ISOTOP? |
发布紧急采购，3分钟左右您将得到回复。