- 您现在的位置：买卖IC网 > PDF目录378679 > MTB16N25E (MOTOROLA INC) TMOS POWER FET 16 AMPERES PDF资料下载
参数资料
| 型号： | MTB16N25E |
| 厂商： | MOTOROLA INC |
| 元件分类： | JFETs |
| 英文描述： | TMOS POWER FET 16 AMPERES |
| 中文描述： | 16 A, 250 V, 0.25 ohm, N-CHANNEL, Si, POWER, MOSFET |
| 文件页数： | 9/10页 |
| 文件大小： | 259K |
| 代理商： | MTB16N25E |
9
Motorola TMOS Power MOSFET Transistor Device Data
TYPICAL SOLDER HEATING PROFILE
For any given circuit board, there will be a group of control
settings that will give the desired heat pattern. The operator
must set temperatures for several heating zones, and a figure
for belt speed. Taken together, these control settings make up
a heating “profile” for that particular circuit board. On
machines controlled by a computer, the computer remembers
these profiles from one operating session to the next. Figure
18 shows a typical heating profile for use when soldering a
surface mount device to a printed circuit board. This profile will
vary among soldering systems but it is a good starting point.
Factors that can affect the profile include the type of soldering
system in use, density and types of components on the board,
type of solder used, and the type of board or substrate material
being used. This profile shows temperature versus time. The
line on the graph shows the actual temperature that might be
experienced on the surface of a test board at or near a central
solder joint. The two profiles are based on a high density and
a low density board. The Vitronics SMD310 convection/in-
frared reflow soldering system was used to generate this
profile. The type of solder used was 62/36/2 Tin Lead Silver
with a melting point between 177–189
°
C. When this type of
furnace is used for solder reflow work, the circuit boards and
solder joints tend to heat first. The components on the board
are then heated by conduction. The circuit board, because it
has a large surface area, absorbs the thermal energy more
efficiently, then distributes this energy to the components.
Because of this effect, the main body of a component may be
up to 30 degrees cooler than the adjacent solder joints.
STEP 1
PREHEAT
ZONE 1
“RAMP”
STEP 2
VENT
“SOAK”
STEP 3
HEATING
ZONES 2 & 5
“RAMP”
STEP 4
HEATING
ZONES 3 & 6
“SOAK”
STEP 5
HEATING
ZONES 4 & 7
“SPIKE”
170
°
C
STEP 6
VENT
STEP 7
COOLING
200
°
C
150
°
C
100
°
C
50
°
C
TIME (3 TO 7 MINUTES TOTAL)
Figure 18. Typical Solder Heating Profile
TMAX
SOLDER IS LIQUID FOR
40 TO 80 SECONDS
(DEPENDING ON
MASS OF ASSEMBLY)
205
°
TO 219
°
C
PEAK AT
SOLDER JOINT
DESIRED CURVE FOR LOW
MASS ASSEMBLIES
100
°
C
150
°
C
160
°
C
140
°
C
DESIRED CURVE FOR HIGH
MASS ASSEMBLIES
相关PDF资料 |
PDF描述 |
|---|---|
| MTB20N20E | TMOS POWER FET 20 AMPERES 200 VOLTS |
| MTB2N60E | TMOS POWER FET 2.0 AMPERES 600 VOLTS |
| MTB2P50E | TMOS POWER FET 2.0 AMPERES 500 VOLTS |
| MTB30N06VL | TMOS POWER FET 30 AMPERES 60 VOLTS |
| MTB30P06V | TMOS POWER FET 30 AMPERES 60 VOLTS |
相关代理商/技术参数 |
参数描述 |
|---|---|
| MTB16N25ET4 | 制造商:ON Semiconductor 功能描述:Trans MOSFET N-CH 250V 16A 3-Pin(2+Tab) D2PAK T/R 制造商:Rochester Electronics LLC 功能描述:- Bulk |
| MTB16P04J3 | 制造商:CYSTEKEC 制造商全称:Cystech Electonics Corp. 功能描述:P-Channel Enhancement Mode Power MOSFET |
| MTB1-6PAL61 | 制造商:ITT Interconnect Solutions 功能描述:MTB1-6PAL61 - Bulk |
| MTB1-6PAL79 | 制造商:ITT Interconnect Solutions 功能描述: 制造商:ITT Interconnect Solutions 功能描述:Conn Unshrouded Header PIN 6 POS 1.27mm Solder RA Thru-Hole |
| MTB1-6PAL80 | 制造商:ITT Interconnect Solutions 功能描述: 制造商:ITT Interconnect Solutions 功能描述:Conn Unshrouded Header PIN 6 POS 1.27mm Solder RA Thru-Hole |
发布紧急采购，3分钟左右您将得到回复。