参数资料
| 型号： | NCP5322ADW |
| 厂商： | ON Semiconductor |
| 文件页数： | 21/31页 |
| 文件大小： | 0K |
| 描述： | IC CTLR BUCK 2PH DRVR/DAC 28SOIC |
| 产品变化通告： | Product Obsolescence 11/Feb/2009 |
| 标准包装： | 26 |
| 应用： | 控制器，高性能处理器 |
| 输入电压： | 4.5 V ~ 14 V |
| 输出数： | 2 |
| 输出电压： | 3.3V |
| 工作温度： | 0°C ~ 70°C |
| 安装类型： | 表面贴装 |
| 封装/外壳： | 28-SOIC（0.295"，7.50mm 宽） |
| 供应商设备封装： | 28-SOIC |
| 包装： | 管件 |
第1页第2页第3页第4页第5页第6页第7页第8页第9页第10页第11页第12页第13页第14页第15页第16页第17页第18页第19页第20页当前第21页第22页第23页第24页第25页第26页第27页第28页第29页第30页第31页
NCP5322A
at the highest ambient temperature. Power dissipation has two
primary contributors: conduction losses and switching losses.
The control or upper MOSFET will display both switching
and conduction losses. The synchronous or lower MOSFET
will exhibit only conduction losses because it switches into
nearly zero voltage. However, the body diode in the
synchronous MOSFET will suffer diode losses during the
non?overlap time of the gate drivers.
For the upper or control MOSFET, the power dissipation
can be approximated from:
V GS_TH
I D
V GATE
PD,CONTROL + (IRMS,CNTL2 @ RDS(on))
(19)
Q GS1
Q GS2
Q GD
V DRAIN
) (ILo,MAX @ Qswitch Ig @ VIN @ fSW)
) (Qoss 2 @ VIN @ fSW) ) (VIN @ QRR @ fSW)
The first term represents the conduction or IR losses when
the MOSFET is ON while the second term represents the
switching losses. The third term is the losses associated with
the control and synchronous MOSFET output charge when
the control MOSFET turns ON. The output losses are caused
by both the control and synchronous MOSFET but are
dissipated only in the control FET. The fourth term is the loss
due to the reverse recovery time of the body diode in the
synchronous MOSFET. The first two terms are usually
adequate to predict the majority of the losses.
Where I RMS,CNTL is the RMS value of the trapezoidal
current in the control MOSFET:
IRMS,CNTL + [D @ (ILo,MAX2 ) ILo,MAX @ ILo,MIN (20)
) ILo,MIN2) 3]1 2
I Lo,MAX is the maximum output inductor current:
Figure 17. MOSFET Switching Characteristics
I g is the output current from the gate driver IC.
V IN is the input voltage to the converter.
f sw is the switching frequency of the converter.
Q G is the MOSFET total gate charge to obtain R DS(on) .
Commonly specified in the data sheet.
V g is the gate drive voltage.
Q RR is the reverse recovery charge of the lower MOSFET.
Q oss is the MOSFET output charge specified in the data
sheet.
For the lower or synchronous MOSFET, the power
dissipation can be approximated from:
PD,SYNCH + (IRMS,SYNCH2 @ RDS(on))
(26)
) (Vfdiode @ IO,MAX 2 @ t_nonoverlap @ fSW)
The first term represents the conduction or IR losses when
the MOSFET is ON and the second term represents the diode
IRMS,SYNCH + [(1 * D)
ILo,MAX + IO,MAX 2 ) D ILo 2
I Lo,MIN is the minimum output inductor current:
ILo,MIN + IO,MAX 2 * D ILo 2
I O,MAX is the maximum converter output current.
D is the duty cycle of the converter:
D + VOUT VIN
(21)
(22)
(23)
losses that occur during the gate non?overlap time.
All terms were defined in the previous discussion for the
control MOSFET with the exception of:
(27)
@ (ILo,MAX2 ) ILo,MAX @ ILo,MIN ) ILo,MIN2) 3]1 2
where:
D ILo + (VIN * VOUT) @ D (Lo @ fSW)
D I Lo is the peak?to?peak ripple current in the output
inductor of value Lo:
(24)
R DS(on) is the ON resistance of the MOSFET at the
applied gate drive voltage.
Q switch is the post gate threshold portion of the
gate?to?source charge plus the gate?to?drain charge. This
may be specified in the data sheet or approximated from the
gate?charge curve as shown in the Figure 17.
Vf diode is the forward voltage of the MOSFET’s intrinsic
diode at the converter output current.
t_nonoverlap is the non?overlap time between the upper
and lower gate drivers to prevent cross conduction. This
time is usually specified in the data sheet for the control
IC.
When the MOSFET power dissipations are known, the
designer can calculate the required thermal impedance to
maintain a specified junction temperature at the worst case
ambient operating temperature
Qswitch + Qgs2 ) Qgd
(25)
q T t (TJ * TA) PD
(28)
http://onsemi.com
21
相关PDF资料 |
PDF描述 |
|---|---|
| NCP5331FTR2G | IC CTLR PWM 2PH W/DRVRS 32-LQFP |
| NCP5332ADW | IC CTLR BUCK 2PH DRVR/DAC 28SOIC |
| NCP5378MNR2G | IC CTLR 1PH SYNC BUCK 32QFN |
| NCP5380AMNR2G | IC CTLR SYNC BUCK SGL 32QFN |
| NCP5381AMNR2G | IC BUCK CTLR 2/3/4PHASE 40-QFN |
相关代理商/技术参数 |
参数描述 |
|---|---|
| NCP5322ADWG | 制造商:ONSEMI 制造商全称:ON Semiconductor 功能描述:Two−Phase Buck Controller with Integrated Gate Drivers and 5−Bit DAC |
| NCP5322ADWR2 | 功能描述:DC/DC 开关控制器 2 Phase Buck w/Gate RoHS:否 制造商:Texas Instruments 输入电压:6 V to 100 V 开关频率: 输出电压:1.215 V to 80 V 输出电流:3.5 A 输出端数量:1 最大工作温度:+ 125 C 安装风格: 封装 / 箱体:CPAK |
| NCP5322ADWR2G | 制造商:Rochester Electronics LLC 功能描述: 制造商:ON Semiconductor 功能描述: |
| NCP5331 | 制造商:ONSEMI 制造商全称:ON Semiconductor 功能描述:Two-Phase PWM Controller with Integrated Gate Drivers |
| NCP5331/D | 制造商:ONSEMI 制造商全称:ON Semiconductor 功能描述:Two Phase PWM Controller with Integrated Gate Drivers |
发布紧急采购，3分钟左右您将得到回复。