- 您现在的位置：买卖IC网 > PDF目录15211 > NCP5425DBG (ON Semiconductor)IC REG CTRLR BUCK PWM VM 20TSSOP PDF资料下载
参数资料
| 型号： | NCP5425DBG |
| 厂商： | ON Semiconductor |
| 文件页数： | 10/22页 |
| 文件大小： | 0K |
| 描述： | IC REG CTRLR BUCK PWM VM 20TSSOP |
| 标准包装： | 75 |
| PWM 型： | 电压模式 |
| 输出数： | 2 |
| 频率 - 最大： | 938kHz |
| 占空比： | 100% |
| 电源电压： | 4.75 V ~ 13.2 V |
| 降压： | 是 |
| 升压： | 无 |
| 回扫： | 无 |
| 反相： | 无 |
| 倍增器： | 无 |
| 除法器： | 无 |
| Cuk： | 无 |
| 隔离： | 无 |
| 工作温度： | 0°C ~ 125°C |
| 封装/外壳： | 20-TSSOP（0.173"，4.40mm 宽） |
| 包装： | 管件 |
NCP5425
Current Sharing
When used in a two separate input to a single output mode,
the NCP5425 dual controller can provide input power
sharing in either of two ways:
? A preset ratio. For example, Channel 1 could provide
70% of the load current, and Channel 2, the remaining
30%. Practical ratios for Channel 1/Channel 2
contribution to total load current range from 50%?50%
to 80%?20%.
? A preset ratio up to a specific current contribution from
Channel 2. In excess of that limit, all of the additional
load current would be supplied by Channel 1. Figure 7
depicts the actual performance of a NCP5425
configured in a 70%?30% share ratio, with Channel 2
output current limited to 5.0 Amps.
The availability both Channel 2 error amplifier inputs
(signal and reference) at device pins is key to programmable
current ratio sharing. Current sense information from
Channel 1 is connected to the reference input of the Channel
2 error amplifier. Current information from Channel 2 is fed
back to the error amplifier’s inverting input. Channel 2 will
therefore act to adjust its current to match the current
information fed to its reference input from Channel 1. If this
information is one?half the voltage developed across the
Channel 1 output inductor, Channel 2 will run at half the
current and supply a approximately 33% of the total load
current. This application is illustrated in Figure 7.
In some applications the power supply designer may not
only wish to draw a known percentage of power from one
source, but also limit the power drawn from that source. The
current limit amplifier on Channel 2 can be programmed to
budget the maximum input power into Channel 2 and all
power in excess of that limit will be supplied solely by
Channel 1. This is accomplished by setting the Channel 2
cycle?by?cycle current limit in conjunction with
programming the current ratio as described above.
V in
Q3
V in
Q1
L1
V out
L2
Q2
R3
Q4
R1
C3
C2
R2
R
R
C
C1
C
R
C
Master
Error Amp
U2
?
+
V FB1
R4
R
V FB2
V REF2
?
+
Slave
Error Amp
U2
Internal
Reference
0.8 V
Figure 6. Two Phase Current Sharing Circuit
14.00
Channel 1 output current
12.00
10.00
8.00
Iout(1)
share begins to increase
Channel 2 output current
begins to level off at 5
6.00
4.00
2.00
0.00
0
Iout(2)
Iin(1)
Iin(2)
5 10 15
20
Amps
TOTAL OUTPUT CURRENT, AMPS
Figure 7. 70%/30% Current Sharing with Channel 2 Current Limiting
NOTE: Channel 1 input voltage = Channel 2 input voltage = 5.0 V
Output voltage = 1.5 V
http://onsemi.com
10
相关PDF资料 |
PDF描述 |
|---|---|
| CAT825RTDI-GT3 | IC SUPERVISOR MPU 2.63V TSOT23-5 |
| ISL6845IUZ-T | IC REG CTRLR BST FLYBK ISO 8MSOP |
| AGM06DRMH-S288 | CONN EDGECARD EXTEND 12POS .156 |
| ISL6845IRZ-T | IC REG CTRLR BST FLYBK ISO 8-DFN |
| VI-2TN-EY-F4 | CONVERTER MOD DC/DC 18.5V 50W |
相关代理商/技术参数 |
参数描述 |
|---|---|
| NCP5425DBR2 | 功能描述:DC/DC 开关控制器 Dual Synchronous RoHS:否 制造商:Texas Instruments 输入电压:6 V to 100 V 开关频率: 输出电压:1.215 V to 80 V 输出电流:3.5 A 输出端数量:1 最大工作温度:+ 125 C 安装风格: 封装 / 箱体:CPAK |
| NCP5425DBR2G | 功能描述:DC/DC 开关控制器 Dual Synchronous Buck RoHS:否 制造商:Texas Instruments 输入电压:6 V to 100 V 开关频率: 输出电压:1.215 V to 80 V 输出电流:3.5 A 输出端数量:1 最大工作温度:+ 125 C 安装风格: 封装 / 箱体:CPAK |
| NCP5425DOEVB | 功能描述:电源管理IC开发工具 ANA SW REG EVAL BRD RoHS:否 制造商:Maxim Integrated 产品:Evaluation Kits 类型:Battery Management 工具用于评估:MAX17710GB 输入电压: 输出电压:1.8 V |
| NCP5425S0EVB | 制造商:ON Semiconductor 功能描述: |
| NCP5425SOEVB | 功能描述:电源管理IC开发工具 ANA SW REG EVAL BRD RoHS:否 制造商:Maxim Integrated 产品:Evaluation Kits 类型:Battery Management 工具用于评估:MAX17710GB 输入电压: 输出电压:1.8 V |
发布紧急采购，3分钟左右您将得到回复。