- 您现在的位置：买卖IC网 > PDF目录11670 > NCV1124DR2G (ON Semiconductor)IC SENSOR DUAL VAR-RELUCT 8-SOIC PDF资料下载
参数资料
| 型号： | NCV1124DR2G |
| 厂商： | ON Semiconductor |
| 文件页数： | 4/8页 |
| 文件大小： | 0K |
| 描述： | IC SENSOR DUAL VAR-RELUCT 8-SOIC |
| 标准包装： | 2,500 |
| 类型： | 可变磁阻 |
| 输入类型： | 逻辑 |
| 输出类型： | 逻辑 |
| 接口： | 双，串联或并联 |
| 电流 - 电源： | 5mA |
| 安装类型： | 表面贴装 |
| 封装/外壳： | 8-SOIC（0.154"，3.90mm 宽） |
| 供应商设备封装： | 8-SOICN |
| 包装： | 带卷 (TR) |
| 其它名称： | NCV1124DR2G-ND NCV1124DR2GOSTR |
NCV1124
http://onsemi.com
4
THEORY OF OPERATION
NORMAL OPERATION
Figure 2 shows one channel of the NCV1124 along with
the necessary external components. Both channels share the
INAdj pin as the negative input to a comparator. A brief
description of the components is as follows:
VRS Ideal sinusoidal, ground referenced, sensor output
amplitude usually increases with frequency, depending on
loading.
RRS Source impedance of sensor.
R1/RAdj External resistors for current limiting and
biasing.
INP1/INAdj Internal current sources that determine trip
points via R1/RAdj.
COMP1 Internal comparator with builtin hysteresis
set at 160 mV.
OUT1 Output 0 V 5.0 V square wave with the same
frequency as VRS.
By inspection, the voltage at the (+) and () terminals of
COMP1 with VRS = 0V are:
V+
+ INP1(R1 ) RRS)
(1)
V
+ INAdj
RAdj
(2)
As VRS begins to rise and fall, it will be superimposed on
the DC biased voltage at V+.
V+
+ INP1(R1 ) RRS) ) VRS
(3)
To get comparator COMP1 to trip, the following
condition is needed when crossing in the positive direction,
V+
u V ) VHYS
(4)
(VHYS is the builtin hysteresis set to 160 mV), or when
crossing in the negative direction,
V+
t V * VHYS
(5)
Combining equations 2, 3, and 4, we get:
INP1(R1
) RRS) ) VRS u INAdj
RAdj ) VHYS (6)
therefore,
VRS(+TRP) t INAdj
RAdj * INP1(R1 ) RRS) ) VHYS
(7)
It should be evident that tripping on the negative side is:
VRS(TRP) t INAdj
RAdj * INP1(R1 ) RRS) * VHYS
(8)
In normal mode,
INP1
+ INAdj
(9)
We can now rewrite equation (7) as:
VRS(+TR) u INP1(RAdj * R1 * RRS) ) VHYS (10)
By making
RAdj + R1 ) RRS
(11)
you can detect signals with as little amplitude as VHYS.
A design example is given in the applications section.
OPEN SENSOR PROTECTION
The NCV1124 has a DIAG pin that when pulled high (5.0
V), will increase the INAdj current source by roughly 50%.
Equation (7) shows that a larger VRS(+TRP) voltage will be
needed to trip comparator COMP1. However, if no VRS
signal is present, then we can use equations 1, 2, and 4
(equation 5 does not apply in this mode) to get:
INP1(R1
) RRS) u INP1
KI
RAdj ) VHYS (12)
Since RRS is the only unknown variable we can solve for
RRS,
RRS +
INP1
KI
RAdj ) VHYS
INP1
* R1
(13)
Equation (13) shows that if the output switches states
when entering the diag mode with VRS = 0, the sensor
impedance must be greater than the above calculated value.
This can be very useful in diagnosing intermittent sensor.
INPUT PROTECTION
As shown in Figure 2, an active clamp is provided on each
input to limit the voltage on the input pin and prevent
substrate current injection. The clamp is specified to handle
±12 mA. This puts an upper limit on the amplitude of the
sensor output. For example, if R1 = 20 k, then
VRS(MAX) + 20 k
12 mA
+ 240 V
Therefore, the VRS(pkpk) voltage can be as high as 480 V.
The NCV1124 will typically run at a frequency up to 1.8
MHz if the input signal does not activate the positive or
negative input clamps. Frequency performance will be
lower when the positive or negative clamps are active.
Typical performance will be up to a frequency of 680 kHz
with the clamps active.
相关PDF资料 |
PDF描述 |
|---|---|
| MS27508E24B1PB | CONN RCPT 128POS BOX MNT W/PINS |
| D38999/26WJ4PN | CONN PLUG 56POS STRAIGHT W/PINS |
| D38999/20JJ61HN | CONN RCPT 61POS WALL MNT W/PINS |
| VE-JNZ-IW-F3 | CONVERTER MOD DC/DC 2V 40W |
| D38999/20WH21SN | CONN RCPT 21POS WALL MNT W/SCKT |
相关代理商/技术参数 |
参数描述 |
|---|---|
| NCV1406SNT1G | 功能描述:直流/直流开关转换器 STEP-UP DC-DC CONVERTER RoHS:否 制造商:STMicroelectronics 最大输入电压:4.5 V 开关频率:1.5 MHz 输出电压:4.6 V 输出电流:250 mA 输出端数量:2 最大工作温度:+ 85 C 安装风格:SMD/SMT |
| NCV1413B | 制造商:ONSEMI 制造商全称:ON Semiconductor 功能描述:High Voltage, High Current Darlington Transistor Arrays |
| NCV1413BDR2 | 功能描述:达林顿晶体管 High Voltage High RoHS:否 制造商:Texas Instruments 配置:Octal 晶体管极性:NPN 集电极—发射极最大电压 VCEO:50 V 发射极 - 基极电压 VEBO: 集电极—基极电压 VCBO: 最大直流电集电极电流:0.5 A 最大集电极截止电流: 功率耗散: 最大工作温度:+ 150 C 安装风格:SMD/SMT 封装 / 箱体:SOIC-18 封装:Reel |
| NCV1413BDR2G | 功能描述:达林顿晶体管 High Voltage High Current Darlington RoHS:否 制造商:Texas Instruments 配置:Octal 晶体管极性:NPN 集电极—发射极最大电压 VCEO:50 V 发射极 - 基极电压 VEBO: 集电极—基极电压 VCBO: 最大直流电集电极电流:0.5 A 最大集电极截止电流: 功率耗散: 最大工作温度:+ 150 C 安装风格:SMD/SMT 封装 / 箱体:SOIC-18 封装:Reel |
| NCV1413BDR2G/H | 制造商:ON Semiconductor 功能描述: |
发布紧急采购，3分钟左右您将得到回复。