参数资料
型号: P83C576EHPN
厂商: NXP SEMICONDUCTORS
元件分类: 微控制器/微处理器
英文描述: 80C51 8-bit microcontroller family 8K/256 OTP/ROM, 6 channel 10-bit A/D, 4 comparators, failure detect circuitry, watchdog timer
中文描述: 8-BIT, MROM, 16 MHz, MICROCONTROLLER, PDIP40
封装: 0.600 INCH, PLASTIC, MO-015AJ, SOT-129-1, DIP-40
文件页数: 23/46页
文件大小: 447K
代理商: P83C576EHPN
Philips Semiconductors
Product specification
83C576/87C576
80C51 8-bit microcontroller family
8K/256 OTP/ROM, 6 channel 10-bit A/D, 4 comparators,
failure detect circuitry, watchdog timer
1998 Jun 04
23
SM0
SM1
SM2
REN
TB8
RB8
TI
RI
SCON
(98H)
D0
D1
D2
D3
D4
D5
D6
D7
D8
1
1
1
0
COMPARATOR
1
1
X
RECEIVED ADDRESS D0 TO D7
PROGRAMMED ADDRESS
IN UART MODE 2 OR MODE 3 AND SM2 = 1:
INTERRUPT IF REN=1, RB8=1 AND “RECEIVED ADDRESS” = “PROGRAMMED ADDRESS”
– WHEN OWN ADDRESS RECEIVED, CLEAR SM2 TO RECEIVE DATA BYTES
– WHEN ALL DATA BYTES HAVE BEEN RECEIVED: SET SM2 TO WAIT FOR NEXT ADDRESS.
SU00045
Figure 21.
UART Multiprocessor Communication, Automatic Address Recognition
CMP Register Bit Definitions
CMP.7
enable comparator 3
CMP.6
enable comparator 2
CMP.5
enable comparator 1,
CMP.4
enable comparator 0
CMP.3
comparator 3 output (read only)
CMP.2
comparator 2 output (read only)
CMP.1
comparator 1 output (read only)
CMP.0
comparator 0 output (read only)
All comparators are disabled automatically in power down mode. In
idle mode unused comparators should be disabled by software to
save power. A comparator can generate an interrupt that will
terminate idle mode when used to drive a PCA capture input.
The CMPE register contains bits to enable each comparator to drive
external output pins or internal PCA capture inputs. When the
comparator is configured for external output, the user must also
configure the output port in one of its output modes. The comparator
output is wire-ORed with the corresponding port SFR bit, so the
SFR bit must also be set by software to enable the output.
CMPE Register Bit Definitions
CMPE.7 enables comparator 3 to drive CEX3
CMPE.6 enables comparator 2 to drive CEX2
CMPE.5 enables comparator 1 to drive CEX1
CMPE.4 enables comparator 0 to drive CEX0
CMPE.3 enables comparator 3 output on P2.3
CMPE.2 enables comparator 2 output on P2.2
CMPE.1 enables comparator 1 output on P2.1
CMPE.0 enables comparator 0 output on P2.0
When 1s are written to CMPE bits 7-4, the comparator outputs will
drive the corresponding capture input. When 1s are written to CMPE
bits 3-0 the comparator output will also drive the corresponding
port 2 pin. If the comparator’s enabled to drive the capture input but
not the port pin, then the port pin can be used for general purpose
I/O. When a comparator output is enabled, the user will need to
configure the port for one of its output modes.
There are two special function registers associated with the
comparators. They are CMP which contains the comparator enables
and a bit that can be read by software to determine the state of each
comparator’s output, and CMPE which controls whether the output
from each comparator drives the associated output pin or a capture
input associated with one of the PCA modules.
The CMP registers bits 0–3 can be read by software to determine
the state of the output of each comparator. To do this the associated
comparator must be enabled but the output in port 2 can be
disabled. This allows easy polling of the comparator output value
without the need to use up a port pin.
The CMPE register allows the comparator to drive the associated
PCA module capture input, so that on compare a capture can be
generated in the PCA. Bits 0–3 of this register enable the
comparator output to drive the associated port 2 output circuitry.
Used as a comparator output, the output mode for this port must be
configured for output by the user and the port output SFR bit latch
must be set. If the comparator is not enabled to drive the port 2
circuitry, the associated port 2 pin can be used for other I/O. This
includes when a comparator is enabled to drive the capture input to
a PCA module.
Reduced EMI Mode
There are two bits in the AUXR register that can be set to reduce
the internal clock drive and disable the ALE output. AO (AUXR.0)
when set turns off the ALE output. LO (AUXR.1) when set reduces
the drive of the internal clock circuitry. Both bits are cleared on
Reset. With LO set the 8XC576 will still operate at 12MHz, and will
have reduced EMI in the range above 100MHz.
8XC576 Reduced EMI Mode
AUXR (0X8E)
––
––
––
––
RST
TXI
LO
AO
AO:
LO:
Turns off ALE output.
Reduces drive of internal clock circuitry. 8XC576 spec’d to
12MHz when LO set.
Inverts TxD when set.
RST: Software reset.
TXI:
相关PDF资料
PDF描述
P87C576EHPN 80C51 8-bit microcontroller family 8K/256 OTP/ROM, 6 channel 10-bit A/D, 4 comparators, failure detect circuitry, watchdog timer
P83C576EBBB 80C51 8-bit microcontroller family 8K/256 OTP/ROM, 6 channel 10-bit A/D, 4 comparators, failure detect circuitry, watchdog timer
P87C576EBBB 80C51 8-bit microcontroller family 8K/256 OTP/ROM, 6 channel 10-bit A/D, 4 comparators, failure detect circuitry, watchdog timer
P87C576EBAA 80C51 8-bit microcontroller family 8K/256 OTP/ROM, 6 channel 10-bit A/D, 4 comparators, failure detect circuitry, watchdog timer
P83C576EBPN 80C51 8-bit microcontroller family 8K/256 OTP/ROM, 6 channel 10-bit A/D, 4 comparators, failure detect circuitry, watchdog timer
相关代理商/技术参数
参数描述
P83C591 制造商:PHILIPS 制造商全称:NXP Semiconductors 功能描述:Single-chip 8-bit microcontroller with CAN controller
P83C591SFA 制造商:PHILIPS 制造商全称:NXP Semiconductors 功能描述:Single-chip 8-bit microcontroller with CAN controller
P83C591SFB 制造商:PHILIPS 制造商全称:NXP Semiconductors 功能描述:Single-chip 8-bit microcontroller with CAN controller
P83C591VFA 制造商:PHILIPS 制造商全称:NXP Semiconductors 功能描述:Single-chip 8-bit microcontroller with CAN controller
P83C591VFB 制造商:PHILIPS 制造商全称:NXP Semiconductors 功能描述:Single-chip 8-bit microcontroller with CAN controller