参数资料
型号: P89LPC9361FDH,518
厂商: NXP Semiconductors
文件页数: 28/94页
文件大小: 0K
描述: IC MCU 80C51 16KB FLASH 28TSSOP
标准包装: 1
系列: LPC900
核心处理器: 8051
芯体尺寸: 8-位
速度: 18MHz
连通性: I²C,SPI,UART/USART
外围设备: 欠压检测/复位,POR,PWM,温度传感器,WDT
输入/输出数: 26
程序存储器容量: 16KB(16K x 8)
程序存储器类型: 闪存
EEPROM 大小: 512 x 8
RAM 容量: 768 x 8
电压 - 电源 (Vcc/Vdd): 2.4 V ~ 3.6 V
数据转换器: A/D 8x8b; D/A 2x8b
振荡器型: 内部
工作温度: -40°C ~ 85°C
封装/外壳: 28-TSSOP(0.173",4.40mm 宽)
包装: 标准包装
P89LPC9331_9341_9351_9361
All information provided in this document is subject to legal disclaimers.
NXP B.V. 2012. All rights reserved.
Product data sheet
Rev. 5.1 — 20 August 2012
34 of 94
NXP Semiconductors
P89LPC9331/9341/9351/9361
8-bit microcontroller with accelerated two-clock 80C51 core
Each interrupt source can be individually enabled or disabled by setting or clearing a bit in
the interrupt enable registers IEN0 or IEN1. The IEN0 register also contains a global
disable bit, EA, which disables all interrupts.
Each interrupt source can be individually programmed to one of four priority levels by
setting or clearing bits in the interrupt priority registers IP0, IP0H, IP1 and IP1H. An
interrupt service routine in progress can be interrupted by a higher priority interrupt, but
not by another interrupt of the same or lower priority. The highest priority interrupt service
cannot be interrupted by any other interrupt source. If two requests of different priority
levels are pending at the start of an instruction, the request of higher priority level is
serviced.
If requests of the same priority level are pending at the start of an instruction, an internal
polling sequence determines which request is serviced. This is called the arbitration
ranking. Note that the arbitration ranking is only used to resolve pending requests of the
same priority level.
7.15.1 External interrupt inputs
The P89LPC9331/9341/9351/9361 has two external interrupt inputs as well as the
Keypad Interrupt function. The two interrupt inputs are identical to those present on the
standard 80C51 microcontrollers.
These external interrupts can be programmed to be level-triggered or edge-triggered by
setting or clearing bit IT1 or IT0 in Register TCON.
In edge-triggered mode, if successive samples of the INTn pin show a HIGH in one cycle
and a LOW in the next cycle, the interrupt request flag IEn in TCON is set, causing an
interrupt request.
If an external interrupt is enabled when the P89LPC9331/9341/9351/9361 is put into
Power-down or Idle mode, the interrupt will cause the processor to wake-up and resume
operation. Refer to Section 7.18 “Power reduction modes” for details.
相关PDF资料
PDF描述
VI-JN2-IW-F4 CONVERTER MOD DC/DC 15V 100W
VI-JN2-IW-F3 CONVERTER MOD DC/DC 15V 100W
VI-JN2-IW-F1 CONVERTER MOD DC/DC 15V 100W
HI1-0507-2 IC MULTIPLEXER DUAL 8X1 28CDIP
P80C32UFAA,518 IC 80C51 MCU 8BIT ROMLESS 44PLCC
相关代理商/技术参数
参数描述
P89LPC936FA 制造商:NXP Semiconductors 功能描述: 制造商:NXP Semiconductors 功能描述:MCU 8BIT 80C51 16K FLASH PLCC28
P89LPC936FA,529 功能描述:8位微控制器 -MCU 80C51 16K FL 768B RM RoHS:否 制造商:Silicon Labs 核心:8051 处理器系列:C8051F39x 数据总线宽度:8 bit 最大时钟频率:50 MHz 程序存储器大小:16 KB 数据 RAM 大小:1 KB 片上 ADC:Yes 工作电源电压:1.8 V to 3.6 V 工作温度范围:- 40 C to + 105 C 封装 / 箱体:QFN-20 安装风格:SMD/SMT
P89LPC936FA529 制造商:NXP Semiconductors 功能描述:IC 8BIT MCU 80C51 18MHZ LCC-28
P89LPC936FDH 制造商:PHILIPS 制造商全称:NXP Semiconductors 功能描述:8-bit microcontroller with accelerated two-clock 80C51 core 4 kB/8 kB/16 kB 3 V byte-erasable flash with 8-bit ADCs
P89LPC936FDH,518 功能描述:8位微控制器 -MCU 16K FL/768B RoHS:否 制造商:Silicon Labs 核心:8051 处理器系列:C8051F39x 数据总线宽度:8 bit 最大时钟频率:50 MHz 程序存储器大小:16 KB 数据 RAM 大小:1 KB 片上 ADC:Yes 工作电源电压:1.8 V to 3.6 V 工作温度范围:- 40 C to + 105 C 封装 / 箱体:QFN-20 安装风格:SMD/SMT