- 您现在的位置：买卖IC网 > PDF目录11167 > P89LPC9361FDH,518 (NXP Semiconductors)IC MCU 80C51 16KB FLASH 28TSSOP PDF资料下载
参数资料
| 型号： | P89LPC9361FDH,518 |
| 厂商： | NXP Semiconductors |
| 文件页数： | 33/94页 |
| 文件大小： | 0K |
| 描述： | IC MCU 80C51 16KB FLASH 28TSSOP |
| 标准包装： | 1 |
| 系列： | LPC900 |
| 核心处理器： | 8051 |
| 芯体尺寸： | 8-位 |
| 速度： | 18MHz |
| 连通性： | I²C，SPI，UART/USART |
| 外围设备： | 欠压检测/复位，POR，PWM，温度传感器，WDT |
| 输入/输出数： | 26 |
| 程序存储器容量： | 16KB（16K x 8） |
| 程序存储器类型： | 闪存 |
| EEPROM 大小： | 512 x 8 |
| RAM 容量： | 768 x 8 |
| 电压 - 电源 (Vcc/Vdd)： | 2.4 V ~ 3.6 V |
| 数据转换器： | A/D 8x8b; D/A 2x8b |
| 振荡器型： | 内部 |
| 工作温度： | -40°C ~ 85°C |
| 封装/外壳： | 28-TSSOP（0.173"，4.40mm 宽） |
| 包装： | 标准包装 |
第1页第2页第3页第4页第5页第6页第7页第8页第9页第10页第11页第12页第13页第14页第15页第16页第17页第18页第19页第20页第21页第22页第23页第24页第25页第26页第27页第28页第29页第30页第31页第32页当前第33页第34页第35页第36页第37页第38页第39页第40页第41页第42页第43页第44页第45页第46页第47页第48页第49页第50页第51页第52页第53页第54页第55页第56页第57页第58页第59页第60页第61页第62页第63页第64页第65页第66页第67页第68页第69页第70页第71页第72页第73页第74页第75页第76页第77页第78页第79页第80页第81页第82页第83页第84页第85页第86页第87页第88页第89页第90页第91页第92页第93页第94页
P89LPC9331_9341_9351_9361
All information provided in this document is subject to legal disclaimers.
NXP B.V. 2012. All rights reserved.
Product data sheet
Rev. 5.1 — 20 August 2012
39 of 94
NXP Semiconductors
P89LPC9331/9341/9351/9361
8-bit microcontroller with accelerated two-clock 80C51 core
Some chip functions continue to operate and draw power during Power-down mode,
increasing the total power used during power-down. These include: Brownout detect,
watchdog timer, comparators (note that comparators can be powered down separately),
and RTC/system timer. The internal RC oscillator is disabled unless both the RC oscillator
has been selected as the system clock and the RTC is enabled.
7.18.3 Total Power-down mode
This is the same as Power-down mode except that the brownout detection circuitry and
the voltage comparators are also disabled to conserve additional power. The internal RC
oscillator is disabled unless both the RC oscillator has been selected as the system clock
and the RTC is enabled. If the internal RC oscillator is used to clock the RTC during
power-down, there will be high power consumption. Please use an external low frequency
clock to achieve low power with the RTC running during power-down.
7.19 Reset
The P1.5/RST pin can function as either a LOW-active reset input or as a digital input,
P1.5. The Reset Pin Enable (RPE) bit in UCFG1, when set to logic 1, enables the external
reset input function on P1.5. When cleared, P1.5 may be used as an input pin.
Remark: During a power-up sequence, the RPE selection is overridden and this pin
always functions as a reset input. An external circuit connected to this pin should not
hold this pin LOW during a power-on sequence as this will keep the device in reset.
After power-up this pin will function as defined by the RPE bit. Only a power-up reset will
temporarily override the selection defined by RPE bit. Other sources of reset will not
override the RPE bit. When this pin functions as a reset input, an internal pull-up
resistance is connected (see Table 12 “Static characteristics”).
Note: During a power cycle, VDD must fall below VPOR before power is reapplied, in order
to ensure a power-on reset (see Table 12 “Static characteristics”).
Reset can be triggered from the following sources:
External reset pin (during power-up or if user configured via UCFG1)
Power-on detect
Brownout detect
Watchdog timer
Software reset
UART break character detect reset
For every reset source, there is a flag in the Reset Register, RSTSRC. The user can read
this register to determine the most recent reset source. These flag bits can be cleared in
software by writing a logic 0 to the corresponding bit. More than one flag bit may be set:
During a power-on reset, both POF and BOF are set but the other flag bits are
cleared.
A Watchdog reset is similar to a power-on reset, both POF and BOF are set but the
other flag bits are cleared.
For any other reset, previously set flag bits that have not been cleared will remain set.
相关PDF资料 |
PDF描述 |
|---|---|
| VI-JN2-IW-F4 | CONVERTER MOD DC/DC 15V 100W |
| VI-JN2-IW-F3 | CONVERTER MOD DC/DC 15V 100W |
| VI-JN2-IW-F1 | CONVERTER MOD DC/DC 15V 100W |
| HI1-0507-2 | IC MULTIPLEXER DUAL 8X1 28CDIP |
| P80C32UFAA,518 | IC 80C51 MCU 8BIT ROMLESS 44PLCC |
相关代理商/技术参数 |
参数描述 |
|---|---|
| P89LPC936FA | 制造商:NXP Semiconductors 功能描述: 制造商:NXP Semiconductors 功能描述:MCU 8BIT 80C51 16K FLASH PLCC28 |
| P89LPC936FA,529 | 功能描述:8位微控制器 -MCU 80C51 16K FL 768B RM RoHS:否 制造商:Silicon Labs 核心:8051 处理器系列:C8051F39x 数据总线宽度:8 bit 最大时钟频率:50 MHz 程序存储器大小:16 KB 数据 RAM 大小:1 KB 片上 ADC:Yes 工作电源电压:1.8 V to 3.6 V 工作温度范围:- 40 C to + 105 C 封装 / 箱体:QFN-20 安装风格:SMD/SMT |
| P89LPC936FA529 | 制造商:NXP Semiconductors 功能描述:IC 8BIT MCU 80C51 18MHZ LCC-28 |
| P89LPC936FDH | 制造商:PHILIPS 制造商全称:NXP Semiconductors 功能描述:8-bit microcontroller with accelerated two-clock 80C51 core 4 kB/8 kB/16 kB 3 V byte-erasable flash with 8-bit ADCs |
| P89LPC936FDH,518 | 功能描述:8位微控制器 -MCU 16K FL/768B RoHS:否 制造商:Silicon Labs 核心:8051 处理器系列:C8051F39x 数据总线宽度:8 bit 最大时钟频率:50 MHz 程序存储器大小:16 KB 数据 RAM 大小:1 KB 片上 ADC:Yes 工作电源电压:1.8 V to 3.6 V 工作温度范围:- 40 C to + 105 C 封装 / 箱体:QFN-20 安装风格:SMD/SMT |
发布紧急采购，3分钟左右您将得到回复。