- 您现在的位置：买卖IC网 > PDF目录98051 > PCZ33937AEKR2 (FREESCALE SEMICONDUCTOR INC) AC MOTOR CONTROLLER, 0.8 A, PDSO54 PDF资料下载
参数资料
| 型号： | PCZ33937AEKR2 |
| 厂商： | FREESCALE SEMICONDUCTOR INC |
| 元件分类： | 运动控制电子 |
| 英文描述： | AC MOTOR CONTROLLER, 0.8 A, PDSO54 |
| 封装： | 0.65 MM PITCH, ROHS COMPLIANT, SOIC-54 |
| 文件页数： | 29/47页 |
| 文件大小： | 750K |
| 代理商： | PCZ33937AEKR2 |
第1页第2页第3页第4页第5页第6页第7页第8页第9页第10页第11页第12页第13页第14页第15页第16页第17页第18页第19页第20页第21页第22页第23页第24页第25页第26页第27页第28页当前第29页第30页第31页第32页第33页第34页第35页第36页第37页第38页第39页第40页第41页第42页第43页第44页第45页第46页第47页
Analog Integrated Circuit Device Data
Freescale Semiconductor
35
33937
FUNCTIONAL DEVICE OPERATION
LOGIC COMMANDS AND REGISTERS
DEADTIME COMMAND
Deadtime prevents the turn-on of both transistors in the
same phase until the deadtime has expired. The deadtime
timer starts when a FET is commanded off (see Figure 6 and
Figure 16). The deadtime control is disabled by enabling the
FULLON mode.
The deadtime is set by sending the DEADTIME command
(100x xxx1), and then sending a calibration pulse of CS. This
pulse must be 16 times longer than the required deadtime
(see Figure 21). Deadtime is measured in cycle times of the
internal time base, fTB. This measurement is divided by 16
and stored in an internal register to provide the reference for
timing the deadtime between high and low gate transactions
in the same phase.
For example: the internal time base is running at 20 MHz
and a 1.5 s deadtime is required. First a DEADTIME
command is sent (using the SPI), then a CS is sent. The CS
pulse is 16*1.5 = 24 s wide. The IC measures this pulse as
24000 ns/50 ns = 480 clock cycles and stores 480/16 = 30 in
the deadtime register. Until the next deadtime calibration is
performed, 30 clock cycles will separate the turn off and turn
on gate signals in the same phase. The worst case error
immediately after calibration will be +0/-1 time base cycle, for
this example +0 ns/-50 ns. Note that if the internal time base
drifts, the effect on dead time will scale directly.
Sending a ZERO DEADTIME command (100x xxx0) sets
the deadtime timer to 0. However, simultaneous turn-on of
High Side and Low Side FETs in the same phase is still
prevented unless the FULLON command has been
transmitted. There is no calibration pulse expected after
receiving the ZERO DEADTIME command.
After RESET, deadtime is set to the maximum value of 255
time base cycles (typically 15 s).
The IC ignores any SPI data that is sent during the
calibration pulse. If there are any transitions on SI or SCLK
while the Deadtime CS pulse is low, a Framing Error will be
generated, however, the CS pulse will be used to calibrate
the deadtime
Figure 21. Deadtime Calibration
Table 13. .DEADTIME Command
SPI Data Bits
765
432
10
Write
100
x
ZERO/
CALIBRATE
Reset
xxx
x
CS
SCLK
SI
SO
DEADTIME
Command
Deadtime Calibration Pulse
Deadtime
Command
CS
SCLK
SI
SO
相关PDF资料 |
PDF描述 |
|---|---|
| PCZ34670EG | SWITCHING REGULATOR, 400 kHz SWITCHING FREQ-MAX, PDSO20 |
| PD69101ILQ | SWITCHING CONTROLLER, PQCC24 |
| PDT006A0X43-SRZ | DC-DC REG PWR SUPPLY MODULE |
| PDT012A0X3-SRZ | 1-OUTPUT DC-DC REG PWR SUPPLY MODULE |
| PDT012A0X3-SRDZ | 1-OUTPUT DC-DC REG PWR SUPPLY MODULE |
相关代理商/技术参数 |
参数描述 |
|---|---|
| PCZ33999CEK | 制造商:Freescale Semiconductor 功能描述:16 LOW SIDE PWM&SPI - Rail/Tube |
| PD 1/2-0 | 制造商:TE Connectivity 功能描述:HEATSHRINK END CAP 12.7MM PK100 |
| PD 1/4-0 | 制造商:TE Connectivity 功能描述:HEATSHRINK END CAP 6.4MM PK100 制造商:TE Connectivity 功能描述:HEATSHRINK, END CAP, 6.4MM, PK100 制造商:TE Connectivity / Raychem 功能描述:HEATSHRINK, END CAP, 6.4MM, PK100; I.D. Supplied - Metric:6.4mm; I.D. Supplied - Imperial:0.251"; I.D. Recovered Max - Metric:2mm; I.D. Recovered Max - Imperial:0.078"; Shrink Ratio:3:1; Shrink Tubing / Boot Material:PO (Polyolefin);;RoHS Compliant: Yes |
| PD 1/8-0 | 制造商:TE Connectivity 功能描述:HEATSHRINK END CAP 3.2MM PK100 制造商:TE Connectivity 功能描述:HEATSHRINK, END CAP, 3.2MM, PK100 制造商:TE Connectivity 功能描述:HEATSHRINK, END CAP, 3.2MM, PK100, I.D. Supplied - Metric:3.2mm, I.D. Supplied - 制造商:TE Connectivity 功能描述:HEATSHRINK, END CAP, 3.2MM, PK100, I.D. Supplied - Metric:3.2mm, I.D. Supplied - Imperial:0.125", I.D. Recovered Max - Metric:0.58mm, I.D. Recovered Max - Imperial:0.022", Shrink Ratio:3:1, Shrink Tubing / Boot Material:PO , RoHS Compliant: Yes |
| PD 2436 | 制造商:Osram Opto semiconductors 功能描述:Bulk |
发布紧急采购，3分钟左右您将得到回复。