- 您现在的位置：买卖IC网 > PDF目录98051 > PCZ33937AEKR2 (FREESCALE SEMICONDUCTOR INC) AC MOTOR CONTROLLER, 0.8 A, PDSO54 PDF资料下载
参数资料
| 型号： | PCZ33937AEKR2 |
| 厂商： | FREESCALE SEMICONDUCTOR INC |
| 元件分类： | 运动控制电子 |
| 英文描述： | AC MOTOR CONTROLLER, 0.8 A, PDSO54 |
| 封装： | 0.65 MM PITCH, ROHS COMPLIANT, SOIC-54 |
| 文件页数： | 32/47页 |
| 文件大小： | 750K |
| 代理商： | PCZ33937AEKR2 |
第1页第2页第3页第4页第5页第6页第7页第8页第9页第10页第11页第12页第13页第14页第15页第16页第17页第18页第19页第20页第21页第22页第23页第24页第25页第26页第27页第28页第29页第30页第31页当前第32页第33页第34页第35页第36页第37页第38页第39页第40页第41页第42页第43页第44页第45页第46页第47页
Analog Integrated Circuit Device Data
38
Freescale Semiconductor
33937
FUNCTIONAL DEVICE OPERATION
LOGIC COMMANDS AND REGISTERS
IC Initialization
Here is a possible flow to initialize the IC and its software environment.
1. Apply power (VSYS) to module
1.1. With RST still low, VSUP and VSYS current will be low because it will only be leakage and the small hold off bias
current.
2. Remove RST (EN1 and EN2 are still low)
2.1. When RST rises above the threshold, the IC will power-up. The charge pump (if configured) will start, and VPWR and
VLS will stabilize.
2.2. VDD will rise as the internal regulator charges the external reservoir capacitor and the IC will come out of reset.
2.3. Initialize interrupt handler for MCU
2.4. Interrupt will occur because of the RESET (Interrupt processing will occur here)
3. Initialize registers
3.1. Initialize MASK register by sending 0010 xxxx or 0011 xxxx to mask out unwanted interrupts.
3.2. Set desired dead time either by commanding zero dead time or calibrating the dead time.
3.3. Send MODE command with desired bits, and also the Lock bit. e.g. 01000001. This prevents further mode changes.
4. Bring EN1 & EN2 high
5. Initialize the outputs
5.1. Command all Px_LS and Px_HS to logic 1 simultaneously (command ON Low Side, sequentially switching the phases
will reduce the transient with very large bootstrap capacitors and may prevent an unintended reset)
5.2. Command all Px_LS and Px_HS to logic 0 simultaneously (command ON High Side)
5.3. Command all Px_LS and Px_HS to logic 1 simultaneously (command ON Low Side)
5.4. The device is now ready for operation.
MAIN LOOP
1. While (forever)
1.1. Send SPI messages (except NULL1-3), read results
1.2. If sending NULL1-3 messages, use a semaphore to detect interrupts
1.2.1. Set Semaphore flag in RAM
1.2.2. Send NULL1-3
1.2.3. Send NULL0, read SR1-3
1.2.4. If Semaphore is still set, then result is good, else go to 1.2.1 (because an interrupt has gotten in the way)
1.2.5. Clear semaphore
2. END
Interrupt Handler
When an interrupt occurs, the general procedure is to send NULL0 and NULL1 commands to determine what happened, take
corrective action (if needed), clear the fault and return.
Because the return value from an SPI command is actually returned in the subsequent message, main-loop software that tries
to read SR1, SR2 or SR3, may experience an interrupt between sending the SPI command and the subsequent read. Thus if
these registers are to be read, special care must be taken in the software to ensure that the correct results are being interpreted.
1. Interrupt Service Routine:
1.1. Disable further interrupts from the 33937
1.2. Clear semaphore set in 1.2.1 of Main loop. This indicates to the main loop that an interrupt occurred and that the
return value it gets may not be as expected.
1.3. Send NULL0 Command. Ignore return value (the previous command is unknown)
1.4. Send NULL0 Command. The return value will be SR0 from the previous NULL0 command
2. Process Bits in SR0 and correct any faults
3. Send CLINT0 command to clear known (i.e. processed faults from SR0) faults 0:3
4. Send CLINT1 command to clear processed faults 4:7. Note, the return SR0 register from this command is actually read in
the main routine.
5. Re-enable interrupts from the 33937
6. Return
相关PDF资料 |
PDF描述 |
|---|---|
| PCZ34670EG | SWITCHING REGULATOR, 400 kHz SWITCHING FREQ-MAX, PDSO20 |
| PD69101ILQ | SWITCHING CONTROLLER, PQCC24 |
| PDT006A0X43-SRZ | DC-DC REG PWR SUPPLY MODULE |
| PDT012A0X3-SRZ | 1-OUTPUT DC-DC REG PWR SUPPLY MODULE |
| PDT012A0X3-SRDZ | 1-OUTPUT DC-DC REG PWR SUPPLY MODULE |
相关代理商/技术参数 |
参数描述 |
|---|---|
| PCZ33999CEK | 制造商:Freescale Semiconductor 功能描述:16 LOW SIDE PWM&SPI - Rail/Tube |
| PD 1/2-0 | 制造商:TE Connectivity 功能描述:HEATSHRINK END CAP 12.7MM PK100 |
| PD 1/4-0 | 制造商:TE Connectivity 功能描述:HEATSHRINK END CAP 6.4MM PK100 制造商:TE Connectivity 功能描述:HEATSHRINK, END CAP, 6.4MM, PK100 制造商:TE Connectivity / Raychem 功能描述:HEATSHRINK, END CAP, 6.4MM, PK100; I.D. Supplied - Metric:6.4mm; I.D. Supplied - Imperial:0.251"; I.D. Recovered Max - Metric:2mm; I.D. Recovered Max - Imperial:0.078"; Shrink Ratio:3:1; Shrink Tubing / Boot Material:PO (Polyolefin);;RoHS Compliant: Yes |
| PD 1/8-0 | 制造商:TE Connectivity 功能描述:HEATSHRINK END CAP 3.2MM PK100 制造商:TE Connectivity 功能描述:HEATSHRINK, END CAP, 3.2MM, PK100 制造商:TE Connectivity 功能描述:HEATSHRINK, END CAP, 3.2MM, PK100, I.D. Supplied - Metric:3.2mm, I.D. Supplied - 制造商:TE Connectivity 功能描述:HEATSHRINK, END CAP, 3.2MM, PK100, I.D. Supplied - Metric:3.2mm, I.D. Supplied - Imperial:0.125", I.D. Recovered Max - Metric:0.58mm, I.D. Recovered Max - Imperial:0.022", Shrink Ratio:3:1, Shrink Tubing / Boot Material:PO , RoHS Compliant: Yes |
| PD 2436 | 制造商:Osram Opto semiconductors 功能描述:Bulk |
发布紧急采购，3分钟左右您将得到回复。