- 您现在的位置：买卖IC网 > PDF目录98051 > PE33631MLIAA (PEREGRINE SEMICONDUCTOR CORP) PHASE DETECTOR, QCC64 PDF资料下载
参数资料
| 型号： | PE33631MLIAA |
| 厂商： | PEREGRINE SEMICONDUCTOR CORP |
| 元件分类： | PLL合成/DDS/VCOs |
| 英文描述： | PHASE DETECTOR, QCC64 |
| 封装： | 9 X 9 MM, GREEN, QFN-64 |
| 文件页数： | 16/16页 |
| 文件大小： | 295K |
| 代理商： | PE33631MLIAA |
Advance Information
PE33631
Document No. 70-0291-01
│ www.psemi.com
2009 Peregrine Semiconductor Corp. All rights reserved.
Page 9 of 16
Main Counter Chain
Normal Operating Mode
Setting the PRE_ENB control bit “low” enables the
÷10/11 prescaler. The main counter chain then
divides the RF input frequency (Fin) by an integer
or fractional number derived from the values in the
“M”, “A” counters and the DSM input word K. The
accumulator size is 18 bit, so the fractional value
is fixed from the ratio K/218. There is an additional
bit in the DSM that acts like an extra bit (19th bit).
This bit is enabled by asserting the pin
RAND_SEL to “high”. Enabling this bit has the
benefit of reducing the spurious levels. However,
a small frequency offset will occur. This positive
frequency offset is calculated with the following
equation.
foffset = (fr / (R + 1)) / 2
19
(1)
All of the following equations do not take into
account this frequency offset. If this offset is
important to a specific frequency plan, appropriate
account needs to be taken.
In the normal mode, the output from the main
counter chain (fp) is related to the VCO frequency
(Fin) by the following equation:
fp = Fin / [10 x (M + 1) + A + K/2
18]
(2)
where A
≤ M + 1, 1 ≤ M ≤ 511
When the loop is locked, Fin is related to the
reference frequency (fr) by the following equation:
Fin = [10 x (M + 1) + A + K/2
18] x (f
r / (R+1))
(3)
where A
≤ M + 1, 1 ≤ M ≤ 511
A consequence of the upper limit on A is that Fin
must be greater than or equal to 90 x (fr / (R+1)) to
obtain contiguous channels. The A counter can
accept values as high as 15, but in typical
operation it will cycle from 0 to 9 between
increments in M.
Programming the M counter with the minimum
allowed value of “1” will result in a minimum M
counter divide ratio of “2”.
Prescaler Bypass Mode (*)
Setting the frequency control register bit
PRE_ENB “high” allows Fin to bypass the ÷10/11
prescaler. In this mode, the prescaler and A
counter are powered down, and the input VCO
frequency is divided by the M counter directly.
The following equation relates Fin to the reference
frequency fr:
Fin = (M + 1) x (fr / (R+1))
(4)
where 1
≤ M ≤ 511
(*) Only integer mode
In frequency bypass mode, neither A counter or K
counter is used. Therefore, only integer-N
operation is possible.
Reference Counter
The reference counter chain divides the reference
frequency fr down to the phase detector
comparison frequency fc.
The output frequency of the 6-bit R Counter is
related to the reference frequency by the following
equation:
fc = fr / (R + 1)
(5)
where 0
≤ R ≤ 63
Note that programming R with “0” will pass the
reference frequency (fr) directly to the phase
detector.
Register Programming
Serial Interface Mode
While the E_WR input is “low” and the S_WR
input is “low”, serial input data (Sdata input), B0 to
B20, are clocked serially into the primary register
on the rising edge of Sclk, MSB (B0) first. The LSB
is used as address bit. When “0”, the contents
from the primary register are transferred into the
secondary register on the rising edge of either
S_WR according to the timing diagrams shown in
Figure 4. When “1”, data is transferred to the
auxiliary register according to the same timing
diagram. The secondary register is used to
program the various counters, while the auxiliary
register is used to program the DSM.
Data are transferred to the counters as shown in
Table 8 on page 10.
相关PDF资料 |
PDF描述 |
|---|---|
| PE33631MLIAA-Z | PHASE DETECTOR, QCC64 |
| PG001M | STEPPER MOTOR CONTROLLER, 0.015 A, PDIP16 |
| PGA308AIDRKR | SPECIALTY ANALOG CIRCUIT, PQCC10 |
| PGA308AIDRKT | SPECIALTY ANALOG CIRCUIT, PQCC10 |
| PGA308AIDGSRG4 | SPECIALTY ANALOG CIRCUIT, PDSO10 |
相关代理商/技术参数 |
参数描述 |
|---|---|
| PE3364 | 制造商:PASTERNACK 制造商全称:Pasternack Enterprises, Inc. 功能描述:CABLE ASSEMBLY RG223/U BNC FEMALE TO BNC FEMALE |
| PE33641 | 制造商:PASTERNACK 制造商全称:Pasternack Enterprises, Inc. 功能描述:CABLE ASSEMBLY RG58C/U SMC PLUG TO SMC PLUG TO SMC PLUG |
| PE33645LF | 制造商:PASTERNACK 制造商全称:Pasternack Enterprises, Inc. 功能描述:CABLE ASSEMBLY RG142B/U SMC PLUG RIGHT ANGLE TO SMC PLUG RIGHT ANGLE(LEAD FREE) |
| PE33646 | 制造商:PASTERNACK 制造商全称:Pasternack Enterprises, Inc. 功能描述:CABLE ASSEMBLY PE-B150 75 OHM SMC PLUG TO 75 OHM BNC MALE |
| PE33646LF | 制造商:PASTERNACK 制造商全称:Pasternack Enterprises, Inc. 功能描述:CABLE ASSEMBLY PE-B150 75 OHM SMC PLUG TO 75 OHM BNC MALE |
发布紧急采购，3分钟左右您将得到回复。