收藏本站
参数资料
型号： PIC14000-04I/SO
厂商： Microchip Technology
文件页数： 140/153页
文件大小： 0K
描述： IC MCU OTP 4KX14 A/D 28SOIC
产品培训模块： Asynchronous Stimulus
8-bit PIC® Microcontroller Portfolio
标准包装： 27
系列： PIC® 14
核心处理器： PIC
芯体尺寸： 8-位
速度： 4MHz
连通性： I²C
外围设备： POR，温度传感器，WDT
输入/输出数： 20
程序存储器容量： 7KB（4K x 14）
程序存储器类型： OTP
RAM 容量： 192 x 8
电压 - 电源 (Vcc/Vdd)： 2.7 V ~ 6 V
数据转换器： 斜率 A/D
振荡器型： 内部
工作温度： -40°C ~ 85°C
封装/外壳： 28-SOIC（0.295"，7.50mm 宽）
包装： 管件
配用： ISPICR1-ND - ADAPTER IN-CIRCUIT PROGRAMMING
309-1073-ND - ADAPTER 28-SOIC TO 28-SOIC
309-1024-ND - ADAPTER 28-SOIC TO 28-DIP
309-1023-ND - ADAPTER 28-SOIC TO 28-DIP
1996 Microchip Technology Inc.
Preliminary
DS40122B-page 87
PIC14000
10.8.1
SLEEP MODE
The SLEEP mode is entered by executing a SLEEP
instruction.
If SLEEP mode is enabled, the WDT will be cleared but
keep running. The PD bit in the STATUS register is
cleared, the TO bit is set, and on-chip oscillators are
shut off, except the WDT RC oscillator, which continues
to run. The I/O ports maintain the status they had
before the SLEEP command was executed (driving
high, low, or high-impedance).
It is an option while in SLEEP mode to leave the
on-chip oscillator running. This option allows an A/D
conversion to continue while the CPU is in SLEEP
mode. The CPU clocks are stopped in this condition to
preserve power. The operation of the on-chip oscillator
during
SLEEP
is
controlled
by
OSCOFF
(SLPCON<3>). Clearing this bit to ‘0’ allows the oscil-
lator to continue to run. This bit is only active in SLEEP
mode.
For lowest power consumption in this mode, all I/O pins
should be either at VDD or VSS with no external circuitry
drawing current from the I/O pin. I/O pins that are
high-impedance inputs should be pulled high or low
externally to avoid leakage currents caused by oating
inputs. The MCLR pin must be at a logic high level
(VIH). The contribution from any on-chip pull-up
resistors should be considered.
10.8.2
WAKE-UP FROM SLEEP
The PIC14000 can wake up from SLEEP through one
of the following events:
1.
External reset input on MCLR pin
2.
Watchdog Timer time-out (if WDT is enabled)
3.
Interrupt from OSC1/PBTN pin
4.
RC<7:4> port change
5.
I2C (serial port) start/stop bit detect interrupt.
6.
Wake-up on programmable reference compara-
tor interrupt.
7.
A/D conversion complete (comparator trip) inter-
rupt.
8.
A/D timer overow interrupt.
An external reset on MCLR pin causes a device reset.
The
other
wake-up
events
are
considered
a
continuation of program execution. The TO and PD bits
in the STATUS register can be used to determine the
cause of device reset. The PD bit, which is set on
power-up is cleared when SLEEP is invoked. The TO
bit is cleared if a WDT time-out occurred (and caused
a wake-up).
When the SLEEP instruction is being executed, the next
instruction (PC + 1) is pre-fetched. For the device to
wake-up through an interrupt event, the corresponding
interrupt enable bit must be set. Wake-up occurs
regardless of the state of bit GIE. If bit GIE is clear, the
device continues execution at the instruction after the
SLEEP
instruction. If bit GIE is set, the device executes
the instruction after the SLEEP instruction and then
branches to the interrupt address (0004h). In cases
where the execution of the instruction following SLEEP
is not desirable, the user should have a NOP after the
SLEEP
instruction.
The WDT is cleared when the device wakes-up from
sleep, regardless of the source of wake-up.
Note:
If the global interrupts are disabled (GIE is
cleared), but any interrupt source has both
its
interrupt
enable
bit
and
the
corresponding interrupt ag bits set, the
device will immediately wake from SLEEP.
10.8.3
HIBERNATE MODE
HIBERNATE mode is an extension of SLEEP mode
with the following additions.
WDT is forced off
Weak pull-ups on RC<5:0> are disabled
Some input buffers are gated-off (refer to
Section 5.0)
The HIBERNATE mode is entered by executing a
SLEEP
instruction with HIBEN (SLPCON<7>) bit set.
The PIC14000 wakes up from HIBERNATE mode via
all the same mechanisms as SLEEP mode, except for
WDT time-out. HIBERNATE mode allows power con-
sumption to be reduced to a minimum.
相关PDF资料
PDF描述
PIC16C432T-I/SS IC MCU CMOS 8BIT 20MHZ 2K 20SSOP
PIC16C433-I/SO IC MCU CMOS 8BIT 10MHZ 2K 18SOIC
PIC16C505-20I/SL IC MCU OTP 1KX12 14SOIC
PIC16C558-04/SO IC MCU OTP 2KX14 18SOIC
PIC16C57-HSI/P IC MCU OTP 2KX12 28DIP
相关代理商/技术参数
参数描述
PIC14000-20/SO 功能描述:8位微控制器 -MCU 7KB 192 RAM 20 I/O RoHS:否 制造商:Silicon Labs 核心:8051 处理器系列:C8051F39x 数据总线宽度:8 bit 最大时钟频率:50 MHz 程序存储器大小:16 KB 数据 RAM 大小:1 KB 片上 ADC:Yes 工作电源电压:1.8 V to 3.6 V 工作温度范围:- 40 C to + 105 C 封装 / 箱体:QFN-20 安装风格:SMD/SMT
PIC14000-20/SP 功能描述:8位微控制器 -MCU 7KB 192 RAM 20 I/O RoHS:否 制造商:Silicon Labs 核心:8051 处理器系列:C8051F39x 数据总线宽度:8 bit 最大时钟频率:50 MHz 程序存储器大小:16 KB 数据 RAM 大小:1 KB 片上 ADC:Yes 工作电源电压:1.8 V to 3.6 V 工作温度范围:- 40 C to + 105 C 封装 / 箱体:QFN-20 安装风格:SMD/SMT
PIC14000-20/SS 功能描述:8位微控制器 -MCU 7KB 192 RAM 20 I/O RoHS:否 制造商:Silicon Labs 核心:8051 处理器系列:C8051F39x 数据总线宽度:8 bit 最大时钟频率:50 MHz 程序存储器大小:16 KB 数据 RAM 大小:1 KB 片上 ADC:Yes 工作电源电压:1.8 V to 3.6 V 工作温度范围:- 40 C to + 105 C 封装 / 箱体:QFN-20 安装风格:SMD/SMT
PIC14000-20I/P 制造商:Microchip Technology Inc 功能描述:MCU 8BIT PIC14 RISC 7KB EPROM 5V - Bulk
PIC14000-20I/SO 功能描述:8位微控制器 -MCU 7KB 192 RAM 20 I/O RoHS:否 制造商:Silicon Labs 核心:8051 处理器系列:C8051F39x 数据总线宽度:8 bit 最大时钟频率:50 MHz 程序存储器大小:16 KB 数据 RAM 大小:1 KB 片上 ADC:Yes 工作电源电压:1.8 V to 3.6 V 工作温度范围:- 40 C to + 105 C 封装 / 箱体:QFN-20 安装风格:SMD/SMT
发布紧急采购，3分钟左右您将得到回复。

采购需求

(若只采购一条型号，填写一行即可)

发布成功！您可以继续发布采购。也可以进入我的后台，查看报价

发布成功！您可以继续发布采购。也可以进入我的后台，查看报价

*型号 *数量 厂商 批号 封装
添加更多采购

我的联系方式

*
*
*