收藏本站
参数资料
型号： PIC14000-04I/SO
厂商： Microchip Technology
文件页数： 70/153页
文件大小： 0K
描述： IC MCU OTP 4KX14 A/D 28SOIC
产品培训模块： Asynchronous Stimulus
8-bit PIC® Microcontroller Portfolio
标准包装： 27
系列： PIC® 14
核心处理器： PIC
芯体尺寸： 8-位
速度： 4MHz
连通性： I²C
外围设备： POR，温度传感器，WDT
输入/输出数： 20
程序存储器容量： 7KB（4K x 14）
程序存储器类型： OTP
RAM 容量： 192 x 8
电压 - 电源 (Vcc/Vdd)： 2.7 V ~ 6 V
数据转换器： 斜率 A/D
振荡器型： 内部
工作温度： -40°C ~ 85°C
封装/外壳： 28-SOIC（0.295"，7.50mm 宽）
包装： 管件
配用： ISPICR1-ND - ADAPTER IN-CIRCUIT PROGRAMMING
309-1073-ND - ADAPTER 28-SOIC TO 28-SOIC
309-1024-ND - ADAPTER 28-SOIC TO 28-DIP
309-1023-ND - ADAPTER 28-SOIC TO 28-DIP
1996 Microchip Technology Inc.
Preliminary
DS40122B-page 23
PIC14000
4.3
PCL and PCLATH
The program counter (PC) is 13-bits wide. The low
byte, PCL, is a readable and writable register. The high
byte of the PC (PCH) is not directly readable or
writable. PCLATH is a holding register for PC<12:8>
where contents are transferred to the upper byte of the
program counter. When PC is loaded with a new value
during a CALL, GOTO or a write to PCL, the high bits of
PC are loaded from PCLATH as shown in Figure 4-9.
FIGURE 4-9:
LOADING OF PC IN
DIFFERENT SITUATIONS
4.3.1
COMPUTED GOTO
When doing a table read using a computed GOTO
method, care should be exercised if the table location
crosses a PCL memory boundary (each 256 byte
block). Refer to the application note “Table Read Using
the PIC16CXX”(AN556).
4.3.2
STACK
The PIC14000 has an 8 deep x 13-bit wide hardware
stack (Figure 4-1). The stack space is not part of either
program or data space and the stack pointer is not
readable or writable. The PC is PUSHed in the stack
when a CALL instruction is executed or an interrupt is
acknowledged. The stack is POPed in the event of a
RETURN,
RETLW
or a RETFIE instruction execution.
PCLATH is not affected by a “PUSH” or a “POP”
operation.
The stack operates as a circular buffer. This means
that after the stack has been “PUSHed” eight times, the
ninth push overwrites the value that was stored from
the rst push. The tenth push overwrites the second
push (and so on).
Note:
On POR, the contents of the PCLATH
register are unknown. The PCLATH should
be initialized before a CALL, GOTO, or any
instruction that modies the PCL register is
executed.
PC
12
8
7
0
5
PCLATH<4:0>
PCLATH
INST with PCL
as dest
ALU result
GOTO, CALL
Opcode <10:0>
8
PC
12
11 10
0
11
PCLATH<4:3>
PCH
PCL
87
2
PCLATH
PCH
PCL
4.3.3
PROGRAM MEMORY PAGING
The PIC14000 has 4K of program memory, but the
CALL
and GOTO instructions only have a 11-bit address
range. This 11-bit address range allows a branch within
a 2K program memory page size. To allow CALL and
GOTO
instructions to address the entire 4K program
memory address range, there must be another bit to
specify the program memory page. This paging bit
comes from the PCLATH<3> bit (Figure 4-9). When
doing a CALL or GOTO instruction, the user must ensure
that this page bit (PCLATH<3>) is programmed to the
desired program memory page. If a CALL instruction (or
interrupt) is executed, the entire 13-bit PC is pushed
onto
the
stack. Therefore,
manipulation
of
the
PCLATH<3> is not required for the return instructions
(which pops the PC from the stack).
Example 4-1 shows the calling of a subroutine in
page 1 of the program memory. This example assumes
that the PCLATH is saved and restored by the interrupt
service routine (if interrupts are used).
EXAMPLE 4-1:
CALL OF A SUBROUTINE IN
PAGE 1 FROM PAGE 0
Note 1: There are no STATUS bits to indicate
stack
overow
or
stack
underow
conditions.
Note 2: There are no instruction mnemonics
called PUSH nor POP. These are actions
that occur from the execution of the CALL,
RETURN, RETLW,
or RETFIE instructions,
or the vectoring to an interrupt address
Note:
The PIC14000 ignores the PCLATH<4>
bit, which is used for program memory
pages 2 and 3 (1000h-1FFFh). The use of
PCLATH<4>
as
a
general
purpose
read/write bit is not recommended since
this may affect upward compatibility with
future products.
ORG 0X500
BSF
PCLATH,
3 ; Select page 1 (800h-FFFh)
CALL
SUB1_P1
; Call subroutine in
:
; page 1 (800h-FFFh)
:
ORG 0X900
SUB1 P1 :
; called subroutine
:
; page 1 (800h-FFFh)
:
RETURN
; return to page 0
; (000h-7FFh)
相关PDF资料
PDF描述
PIC16C432T-I/SS IC MCU CMOS 8BIT 20MHZ 2K 20SSOP
PIC16C433-I/SO IC MCU CMOS 8BIT 10MHZ 2K 18SOIC
PIC16C505-20I/SL IC MCU OTP 1KX12 14SOIC
PIC16C558-04/SO IC MCU OTP 2KX14 18SOIC
PIC16C57-HSI/P IC MCU OTP 2KX12 28DIP
相关代理商/技术参数
参数描述
PIC14000-20/SO 功能描述:8位微控制器 -MCU 7KB 192 RAM 20 I/O RoHS:否 制造商:Silicon Labs 核心:8051 处理器系列:C8051F39x 数据总线宽度:8 bit 最大时钟频率:50 MHz 程序存储器大小:16 KB 数据 RAM 大小:1 KB 片上 ADC:Yes 工作电源电压:1.8 V to 3.6 V 工作温度范围:- 40 C to + 105 C 封装 / 箱体:QFN-20 安装风格:SMD/SMT
PIC14000-20/SP 功能描述:8位微控制器 -MCU 7KB 192 RAM 20 I/O RoHS:否 制造商:Silicon Labs 核心:8051 处理器系列:C8051F39x 数据总线宽度:8 bit 最大时钟频率:50 MHz 程序存储器大小:16 KB 数据 RAM 大小:1 KB 片上 ADC:Yes 工作电源电压:1.8 V to 3.6 V 工作温度范围:- 40 C to + 105 C 封装 / 箱体:QFN-20 安装风格:SMD/SMT
PIC14000-20/SS 功能描述:8位微控制器 -MCU 7KB 192 RAM 20 I/O RoHS:否 制造商:Silicon Labs 核心:8051 处理器系列:C8051F39x 数据总线宽度:8 bit 最大时钟频率:50 MHz 程序存储器大小:16 KB 数据 RAM 大小:1 KB 片上 ADC:Yes 工作电源电压:1.8 V to 3.6 V 工作温度范围:- 40 C to + 105 C 封装 / 箱体:QFN-20 安装风格:SMD/SMT
PIC14000-20I/P 制造商:Microchip Technology Inc 功能描述:MCU 8BIT PIC14 RISC 7KB EPROM 5V - Bulk
PIC14000-20I/SO 功能描述:8位微控制器 -MCU 7KB 192 RAM 20 I/O RoHS:否 制造商:Silicon Labs 核心:8051 处理器系列:C8051F39x 数据总线宽度:8 bit 最大时钟频率:50 MHz 程序存储器大小:16 KB 数据 RAM 大小:1 KB 片上 ADC:Yes 工作电源电压:1.8 V to 3.6 V 工作温度范围:- 40 C to + 105 C 封装 / 箱体:QFN-20 安装风格:SMD/SMT
发布紧急采购，3分钟左右您将得到回复。

采购需求

(若只采购一条型号，填写一行即可)

发布成功！您可以继续发布采购。也可以进入我的后台，查看报价

发布成功！您可以继续发布采购。也可以进入我的后台，查看报价

*型号 *数量 厂商 批号 封装
添加更多采购

我的联系方式

*
*
*