参数资料
| 型号： | PIC16C765-I/L |
| 厂商： | Microchip Technology |
| 文件页数： | 119/165页 |
| 文件大小： | 0K |
| 描述： | IC MCU OTP 8KX14 USB 44PLCC |
| 产品培训模块： | Asynchronous Stimulus 8-bit PIC® Microcontroller Portfolio |
| 标准包装： | 27 |
| 系列： | PIC® 16C |
| 核心处理器： | PIC |
| 芯体尺寸： | 8-位 |
| 速度： | 24MHz |
| 连通性： | SCI，UART/USART，USB |
| 外围设备： | 欠压检测/复位，POR，PWM，WDT |
| 输入/输出数： | 33 |
| 程序存储器容量： | 14KB（8K x 14） |
| 程序存储器类型： | OTP |
| RAM 容量： | 256 x 8 |
| 电压 - 电源 (Vcc/Vdd)： | 4.35 V ~ 5.25 V |
| 数据转换器： | A/D 8x8b |
| 振荡器型： | 外部 |
| 工作温度： | -40°C ~ 85°C |
| 封装/外壳： | 44-LCC（J 形引线） |
| 包装： | 管件 |
| 产品目录页面： | 636 (CN2011-ZH PDF) |
| 配用： | AC164309-ND - MODULE SKT FOR PM3 44PLCC ISPICR1-ND - ADAPTER IN-CIRCUIT PROGRAMMING 444-1001-ND - DEMO BOARD FOR PICMICRO MCU |
第1页第2页第3页第4页第5页第6页第7页第8页第9页第10页第11页第12页第13页第14页第15页第16页第17页第18页第19页第20页第21页第22页第23页第24页第25页第26页第27页第28页第29页第30页第31页第32页第33页第34页第35页第36页第37页第38页第39页第40页第41页第42页第43页第44页第45页第46页第47页第48页第49页第50页第51页第52页第53页第54页第55页第56页第57页第58页第59页第60页第61页第62页第63页第64页第65页第66页第67页第68页第69页第70页第71页第72页第73页第74页第75页第76页第77页第78页第79页第80页第81页第82页第83页第84页第85页第86页第87页第88页第89页第90页第91页第92页第93页第94页第95页第96页第97页第98页第99页第100页第101页第102页第103页第104页第105页第106页第107页第108页第109页第110页第111页第112页第113页第114页第115页第116页第117页第118页当前第119页第120页第121页第122页第123页第124页第125页第126页第127页第128页第129页第130页第131页第132页第133页第134页第135页第136页第137页第138页第139页第140页第141页第142页第143页第144页第145页第146页第147页第148页第149页第150页第151页第152页第153页第154页第155页第156页第157页第158页第159页第160页第161页第162页第163页第164页第165页
2000 Microchip Technology Inc.
Preliminary
DS41124C-page 57
PIC16C745/765
10.0
UNIVERSAL SERIAL BUS
10.1
Overview
This section introduces a minimum amount of informa-
tion on USB. If you already have basic knowledge of
USB, you can safely skip this section. If terms like
Enumeration, Endpoint, IN/OUT Transactions, Trans-
fers and Low Speed/Full Speed are foreign to you,
read on.
USB was developed to address the increased connec-
tivity needs of PC’s in the PC 2000 specification.
There was a base requirement to increase the band-
width and number of devices, which could be
attached. Also desired were the ability for hot swap-
ping, user friendly operation, robust communications
and low cost. The primary promoters of USB are Intel,
Compaq, Microsoft and NEC.
USB is implemented as a Tiered Star topology, with
the host at the top, hubs in the middle, spreading out
to the individual devices at the end. USB is limited to
127 devices on the bus, and the tree cannot be more
than 6 levels deep.
USB is a host centric architecture. The host is always
the master. Devices are not allowed to “speak” unless
“spoken to” by the host.
Transfers take place at one of two speeds. Full Speed
is 12 Mb/s and Low Speed is 1.5 Mb/s. Full Speed
covers the middle ground of data intensive audio and
compressed video applications, while low speed sup-
ports less data intensive applications.
10.1.1
TRANSFER PROTOCOLS
Full speed supports four transfer types: Isochronous,
Bulk, Interrupt and Control. Low speed supports two
transfer types: Interrupt and Control. The four transfer
types are described below.
- Isochronous Transfers, meaning equal
time, guarantee a fixed amount of data at a
fixed rate. This mode trades off guaranteed
data accuracy for guaranteed timeliness.
Data validity is not checked because there
isn’t time to re-send bad packets anyway and
the consequences of bad data are not
catastrophic.
- Bulk Transfers are the converse of Iso-
chronous. Data accuracy is guaranteed, but
timeliness is not.
- Interrupt Transfers are designed to commu-
nicate with devices which have a moderate
data rate requirement. Human Interface
Devices like keyboards are but one example.
For Interrupt Transfers, the key is the desire
to transfer data at regular intervals. USB peri-
odically polls these devices at a fixed rate to
see if there is data to transfer.
- Control Transfers are used for configuration
purposes.
10.1.2
FRAMES
Information communicated on the bus is grouped in a
format called Frames. Each Frame is 1 ms in duration
and is composed of multiple transfers. Each transfer
type can be repeated more than once within a frame.
10.1.3
POWER
Power has always been a concern with any device.
With USB, 5 volt power is now available directly from
the bus. Devices may be self-powered or bus-
powered. Self-powered devices will draw power from
a wall adapter or power brick. On the other hand, bus-
powered devices will draw power directly from the
USB bus itself. There are limits to how much power
can be drawn from the USB bus. Power is expressed
in terms of “unit loads” (
≤100 mA). All devices, includ-
ing Hubs, are guaranteed at least 1 unit load (low
power), but must negotiate with the host for up to 5
unit loads (high power). If the host determines that the
bus as currently configured cannot support a device’s
request for more unit loads, the device will be denied
the extra unit loads and must remain in a low power
configuration.
10.1.4
END POINTS
At the lowest level, each device controls one or more
endpoints. An endpoint can be thought of as a virtual
port. Endpoints are used to communicate with a
device’s functions. Each endpoint is a source or sink of
data. Endpoints have both an In and Out direction
associated with it. Each device must implement end-
point 0 to support Control Transfers for configuration.
There are a maximum of 15 endpoints available for
use by each full speed device and 6 endpoints for
each slow speed device. Remember that the bus is
host centric, so In/Out is with respect to the host and
not the device.
10.1.5
ENUMERATION
Prior to communicating on the bus, the host must see
that a new device has been connected and then go
through an “enumeration process”. This process
allows the host to ask the device to introduce itself,
and negotiate performance parameters, such as
power consumption, transfer protocol and polling rate.
The enumeration process is initiated by the host when
it detects that a new device has attached itself to the
bus. This takes place completely in the background
from the application process.
10.1.6
DESCRIPTORS
The USB specification requires a number of different
descriptors to provide information necessary to identify
a device, specify its endpoints, and each endpoint’s
function. The five general categories of descriptors are
Device, Configuration, Interface, End Point and String.
745cov.book Page 57 Wednesday, August 2, 2000 8:24 AM
相关PDF资料 |
PDF描述 |
|---|---|
| ATMEGA88-20PU | IC AVR MCU 8K 20MHZ 5V 28DIP |
| DSPIC33FJ64MC204-I/PT | IC DSPIC MCU/DSP 64K 44-TQFP |
| PIC24HJ64GP206-I/PT | IC PIC MCU FLASH 64KB 64TQFP |
| DSPIC33FJ64GP206-I/PT | IC DSPIC MCU/DSP 64K 64TQFP |
| DSPIC30F3014-30I/ML | IC DSPIC MCU/DSP 24K 44QFN |
相关代理商/技术参数 |
参数描述 |
|---|---|
| PIC16C765T-I/L | 功能描述:8位微控制器 -MCU 14KB 256 RAM 33 I/O RoHS:否 制造商:Silicon Labs 核心:8051 处理器系列:C8051F39x 数据总线宽度:8 bit 最大时钟频率:50 MHz 程序存储器大小:16 KB 数据 RAM 大小:1 KB 片上 ADC:Yes 工作电源电压:1.8 V to 3.6 V 工作温度范围:- 40 C to + 105 C 封装 / 箱体:QFN-20 安装风格:SMD/SMT |
| PIC16C765T-I/PT | 功能描述:8位微控制器 -MCU 14KB 256 RAM 33 I/O RoHS:否 制造商:Silicon Labs 核心:8051 处理器系列:C8051F39x 数据总线宽度:8 bit 最大时钟频率:50 MHz 程序存储器大小:16 KB 数据 RAM 大小:1 KB 片上 ADC:Yes 工作电源电压:1.8 V to 3.6 V 工作温度范围:- 40 C to + 105 C 封装 / 箱体:QFN-20 安装风格:SMD/SMT |
| PIC16C76T-04/SO | 功能描述:8位微控制器 -MCU 14KB 368 RAM 22 I/O RoHS:否 制造商:Silicon Labs 核心:8051 处理器系列:C8051F39x 数据总线宽度:8 bit 最大时钟频率:50 MHz 程序存储器大小:16 KB 数据 RAM 大小:1 KB 片上 ADC:Yes 工作电源电压:1.8 V to 3.6 V 工作温度范围:- 40 C to + 105 C 封装 / 箱体:QFN-20 安装风格:SMD/SMT |
| PIC16C76T-04E/SO | 功能描述:8位微控制器 -MCU 14KB 368 RAM 22 I/O RoHS:否 制造商:Silicon Labs 核心:8051 处理器系列:C8051F39x 数据总线宽度:8 bit 最大时钟频率:50 MHz 程序存储器大小:16 KB 数据 RAM 大小:1 KB 片上 ADC:Yes 工作电源电压:1.8 V to 3.6 V 工作温度范围:- 40 C to + 105 C 封装 / 箱体:QFN-20 安装风格:SMD/SMT |
| PIC16C76T-04I/SO | 功能描述:8位微控制器 -MCU 14KB 368 RAM 22 I/O RoHS:否 制造商:Silicon Labs 核心:8051 处理器系列:C8051F39x 数据总线宽度:8 bit 最大时钟频率:50 MHz 程序存储器大小:16 KB 数据 RAM 大小:1 KB 片上 ADC:Yes 工作电源电压:1.8 V to 3.6 V 工作温度范围:- 40 C to + 105 C 封装 / 箱体:QFN-20 安装风格:SMD/SMT |
发布紧急采购，3分钟左右您将得到回复。