- 您现在的位置：买卖IC网 > PDF目录69306 > R5F212BASDFP 16-BIT, FLASH, 20 MHz, RISC MICROCONTROLLER, PQFP48 PDF资料下载
参数资料
| 型号： | R5F212BASDFP |
| 元件分类： | 微控制器/微处理器 |
| 英文描述： | 16-BIT, FLASH, 20 MHz, RISC MICROCONTROLLER, PQFP48 |
| 封装： | 10 X 10 MM, 0.50 MM PITCH, PLASTIC, LQFP-48 |
| 文件页数： | 56/138页 |
| 文件大小： | 492K |
| 代理商： | R5F212BASDFP |
第1页第2页第3页第4页第5页第6页第7页第8页第9页第10页第11页第12页第13页第14页第15页第16页第17页第18页第19页第20页第21页第22页第23页第24页第25页第26页第27页第28页第29页第30页第31页第32页第33页第34页第35页第36页第37页第38页第39页第40页第41页第42页第43页第44页第45页第46页第47页第48页第49页第50页第51页第52页第53页第54页第55页当前第56页第57页第58页第59页第60页第61页第62页第63页第64页第65页第66页第67页第68页第69页第70页第71页第72页第73页第74页第75页第76页第77页第78页第79页第80页第81页第82页第83页第84页第85页第86页第87页第88页第89页第90页第91页第92页第93页第94页第95页第96页第97页第98页第99页第100页第101页第102页第103页第104页第105页第106页第107页第108页第109页第110页第111页第112页第113页第114页第115页第116页第117页第118页第119页第120页第121页第122页第123页第124页第125页第126页第127页第128页第129页第130页第131页第132页第133页第134页第135页第136页第137页第138页
236
4317K–AVR–03/2013
AT90PWM2/3/2B/3B
21.2
Operation
The ADC converts an analog input voltage to a 10-bit digital value through successive approxi-
mation. The minimum value represents GND and the maximum value represents the voltage on
the AREF pin minus 1 LSB. Optionally, AV
CC or an internal 2.56V reference voltage may be con-
nected to the AREF pin by writing to the REFSn bits in the ADMUX Register. The internal
voltage reference may thus be decoupled by an external capacitor at the AREF pin to improve
noise immunity.
The analog input channel are selected by writing to the MUX bits in ADMUX. Any of the ADC
input pins, as well as GND and a fixed bandgap voltage reference, can be selected as single
ended inputs to the ADC.
The ADC is enabled by setting the ADC Enable bit, ADEN in ADCSRA. Voltage reference is set
by the REFS1 and REFS0 bits in ADMUX register, whatever the ADC is enabled or not. The
ADC does not consume power when ADEN is cleared, so it is recommended to switch off the
ADC before entering power saving sleep modes.
The ADC generates a 10-bit result which is presented in the ADC Data Registers, ADCH and
ADCL. By default, the result is presented right adjusted, but can optionally be presented left
adjusted by setting the ADLAR bit in ADMUX.
If the result is left adjusted and no more than 8-bit precision is required, it is sufficient to read
ADCH. Otherwise, ADCL must be read first, then ADCH, to ensure that the content of the Data
Registers belongs to the same conversion. Once ADCL is read, ADC access to Data Registers
is blocked. This means that if ADCL has been read, and a conversion completed before ADCH
is read, neither register is updated and the result from the conversion is lost. When ADCH is
read, ADC access to the ADCH and ADCL Registers is re-enabled.
The ADC has its own interrupt which can be triggered when a conversion completes. The ADC
access to the Data Registers is prohibited between reading of ADCH and ADCL, the interrupt
will trigger even if the result is lost.
21.3
Starting a Conversion
A single conversion is started by writing a logical one to the ADC Start Conversion bit, ADSC.
This bit stays high as long as the conversion is in progress and will be cleared by hardware
when the conversion is completed. If a different data channel is selected while a conversion is in
progress, the ADC will finish the current conversion before performing the channel change.
Alternatively, a conversion can be triggered automatically by various sources. Auto Triggering is
enabled by setting the ADC Auto Trigger Enable bit, ADATE in ADCSRA. The trigger source is
selected by setting the ADC Trigger Select bits, ADTS in ADCSRB (See description of the ADTS
bits for a list of the trigger sources). When a positive edge occurs on the selected trigger signal,
the ADC prescaler is reset and a conversion is started. This provides a method of starting con-
versions at fixed intervals. If the trigger signal is still set when the conversion completes, a new
conversion will not be started. If another positive edge occurs on the trigger signal during con-
version, the edge will be ignored. Note that an interrupt flag will be set even if the specific
interrupt is disabled or the Global Interrupt Enable bit in SREG is cleared. A conversion can thus
be triggered without causing an interrupt. However, the interrupt flag must be cleared in order to
trigger a new conversion at the next interrupt event.
相关PDF资料 |
PDF描述 |
|---|---|
| R5F212BASNFA | 16-BIT, FLASH, 20 MHz, RISC MICROCONTROLLER, PQFP48 |
| R5F212ACSDFP | 16-BIT, FLASH, 20 MHz, RISC MICROCONTROLLER, PQFP48 |
| R5F212BCSNFP | 16-BIT, FLASH, 20 MHz, RISC MICROCONTROLLER, PQFP48 |
| R5F212BASNFP | 16-BIT, FLASH, 20 MHz, RISC MICROCONTROLLER, PQFP48 |
| R5F212ACSNFP | 16-BIT, FLASH, 20 MHz, RISC MICROCONTROLLER, PQFP48 |
相关代理商/技术参数 |
参数描述 |
|---|---|
| R5F212BASDFP#U0 | 制造商:Renesas Electronics Corporation 功能描述:MCU 16-Bit R8C CISC 96KB Flash 2.5V/3.3V/5V 64-Pin LQFP 制造商:Renesas Electronics Corporation 功能描述:MCU 16-bit R8C CISC 96KB Flash 2.5V/3.3V/5V 64-Pin LQFP |
| R5F212BASDFP#V0 | 功能描述:IC R8C/2B MCU FLASH 64LQFP RoHS:是 类别:集成电路 (IC) >> 嵌入式 - 微控制器， 系列:R8C/2x/2B 标准包装:250 系列:56F8xxx 核心处理器:56800E 芯体尺寸:16-位 速度:60MHz 连通性:CAN，SCI，SPI 外围设备:POR，PWM，温度传感器，WDT 输入/输出数:21 程序存储器容量:40KB（20K x 16） 程序存储器类型:闪存 EEPROM 大小:- RAM 容量:6K x 16 电压 - 电源 (Vcc/Vdd):2.25 V ~ 3.6 V 数据转换器:A/D 6x12b 振荡器型:内部 工作温度:-40°C ~ 125°C 封装/外壳:48-LQFP 包装:托盘 配用:MC56F8323EVME-ND - BOARD EVALUATION MC56F8323 |
| R5F212BASDFP#V2 | 制造商:Renesas Electronics Corporation 功能描述:R8C/2B 96+2/7 64LQFP 10X10 -40 制造商:Renesas Electronics Corporation 功能描述:R8C/2B 96+2/7 64LQFP 10X10 -40 TO +85 - Trays 制造商:Renesas Electronics Corporation 功能描述:IC MCU 16BIT 96KB FLASH 64LQFP |
| R5F212BASDXXXFA | 制造商:RENESAS 制造商全称:Renesas Technology Corp 功能描述:RENESAS MCU R8C FAMILY / R8C/2x SERIES |
| R5F212BASDXXXFP | 制造商:RENESAS 制造商全称:Renesas Technology Corp 功能描述:RENESAS MCU R8C FAMILY / R8C/2x SERIES |
发布紧急采购，3分钟左右您将得到回复。