- 您现在的位置：买卖IC网 > PDF目录69306 > R5F212BASDFP 16-BIT, FLASH, 20 MHz, RISC MICROCONTROLLER, PQFP48 PDF资料下载
参数资料
| 型号： | R5F212BASDFP |
| 元件分类： | 微控制器/微处理器 |
| 英文描述： | 16-BIT, FLASH, 20 MHz, RISC MICROCONTROLLER, PQFP48 |
| 封装： | 10 X 10 MM, 0.50 MM PITCH, PLASTIC, LQFP-48 |
| 文件页数： | 61/138页 |
| 文件大小： | 492K |
| 代理商： | R5F212BASDFP |
第1页第2页第3页第4页第5页第6页第7页第8页第9页第10页第11页第12页第13页第14页第15页第16页第17页第18页第19页第20页第21页第22页第23页第24页第25页第26页第27页第28页第29页第30页第31页第32页第33页第34页第35页第36页第37页第38页第39页第40页第41页第42页第43页第44页第45页第46页第47页第48页第49页第50页第51页第52页第53页第54页第55页第56页第57页第58页第59页第60页当前第61页第62页第63页第64页第65页第66页第67页第68页第69页第70页第71页第72页第73页第74页第75页第76页第77页第78页第79页第80页第81页第82页第83页第84页第85页第86页第87页第88页第89页第90页第91页第92页第93页第94页第95页第96页第97页第98页第99页第100页第101页第102页第103页第104页第105页第106页第107页第108页第109页第110页第111页第112页第113页第114页第115页第116页第117页第118页第119页第120页第121页第122页第123页第124页第125页第126页第127页第128页第129页第130页第131页第132页第133页第134页第135页第136页第137页第138页
240
4317K–AVR–03/2013
AT90PWM2/3/2B/3B
If Auto Triggering is used, the exact time of the triggering event can be indeterministic. Special
care must be taken when updating the ADMUX Register, in order to control which conversion
will be affected by the new settings.
If both ADATE and ADEN is written to one, an interrupt event can occur at any time. If the
ADMUX Register is changed in this period, the user cannot tell if the next conversion is based
on the old or the new settings. ADMUX can be safely updated in the following ways:
1.
When ADATE or ADEN is cleared.
2.
During conversion, minimum one ADC clock cycle after the trigger event.
3.
After a conversion, before the interrupt flag used as trigger source is cleared.
When updating ADMUX in one of these conditions, the new settings will affect the next ADC
conversion.
In order to start a conversion on an amplified channel, in AT90PWM2/3 version only, there is a
dedicated ADASCR bit in ADCSRB register which waits for the next amplifier trigger event
before really starting the conversion by an hardware setting of the ADSC bit in ADCSRA
register.
21.5.1
ADC Input Channels
When changing channel selections, the user should observe the following guidelines to ensure
that the correct channel is selected:
In Single Conversion mode, always select the channel before starting the conversion. The
channel selection may be changed one ADC clock cycle after writing one to ADSC.
However, the simplest method is to wait for the conversion to complete before changing the
channel selection.
In Free Running mode, always select the channel before starting the first conversion. The
channel selection may be changed one ADC clock cycle after writing one to ADSC.
However, the simplest method is to wait for the first conversion to complete, and then
change the channel selection. Since the next conversion has already started automatically,
the next result will reflect the previous channel selection. Subsequent conversions will reflect
the new channel selection.
In Free Running mode, because the amplifier clear the ADSC bit at the end of an amplified
conversion, it is not possible to use the free running mode, unless ADSC bit is set again by
soft at the end of each conversion.
21.5.2
ADC Voltage Reference
The reference voltage for the ADC (V
REF) indicates the conversion range for the ADC. Single
ended channels that exceed V
REF will result in codes close to 0x3FF. VREF can be selected as
either AV
CC, internal 2.56V reference, or external AREF pin.
AV
CC is connected to the ADC through a passive switch. The internal 2.56V reference is gener-
ated from the internal bandgap reference (V
BG) through an internal amplifier. In either case, the
external AREF pin is directly connected to the ADC, and the reference voltage can be made
more immune to noise by connecting a capacitor between the AREF pin and ground. V
REF can
also be measured at the AREF pin with a high impedant voltmeter. Note that V
REF is a high
impedant source, and only a capacitive load should be connected in a system.
If the user has a fixed voltage source connected to the AREF pin, the user may not use the other
reference voltage options in the application, as they will be shorted to the external voltage. If no
external voltage is applied to the AREF pin, the user may switch between AV
CC and 2.56V as
reference selection. The first ADC conversion result after switching reference voltage source
may be inaccurate, and the user is advised to discard this result.
相关PDF资料 |
PDF描述 |
|---|---|
| R5F212BASNFA | 16-BIT, FLASH, 20 MHz, RISC MICROCONTROLLER, PQFP48 |
| R5F212ACSDFP | 16-BIT, FLASH, 20 MHz, RISC MICROCONTROLLER, PQFP48 |
| R5F212BCSNFP | 16-BIT, FLASH, 20 MHz, RISC MICROCONTROLLER, PQFP48 |
| R5F212BASNFP | 16-BIT, FLASH, 20 MHz, RISC MICROCONTROLLER, PQFP48 |
| R5F212ACSNFP | 16-BIT, FLASH, 20 MHz, RISC MICROCONTROLLER, PQFP48 |
相关代理商/技术参数 |
参数描述 |
|---|---|
| R5F212BASDFP#U0 | 制造商:Renesas Electronics Corporation 功能描述:MCU 16-Bit R8C CISC 96KB Flash 2.5V/3.3V/5V 64-Pin LQFP 制造商:Renesas Electronics Corporation 功能描述:MCU 16-bit R8C CISC 96KB Flash 2.5V/3.3V/5V 64-Pin LQFP |
| R5F212BASDFP#V0 | 功能描述:IC R8C/2B MCU FLASH 64LQFP RoHS:是 类别:集成电路 (IC) >> 嵌入式 - 微控制器， 系列:R8C/2x/2B 标准包装:250 系列:56F8xxx 核心处理器:56800E 芯体尺寸:16-位 速度:60MHz 连通性:CAN，SCI，SPI 外围设备:POR，PWM，温度传感器，WDT 输入/输出数:21 程序存储器容量:40KB（20K x 16） 程序存储器类型:闪存 EEPROM 大小:- RAM 容量:6K x 16 电压 - 电源 (Vcc/Vdd):2.25 V ~ 3.6 V 数据转换器:A/D 6x12b 振荡器型:内部 工作温度:-40°C ~ 125°C 封装/外壳:48-LQFP 包装:托盘 配用:MC56F8323EVME-ND - BOARD EVALUATION MC56F8323 |
| R5F212BASDFP#V2 | 制造商:Renesas Electronics Corporation 功能描述:R8C/2B 96+2/7 64LQFP 10X10 -40 制造商:Renesas Electronics Corporation 功能描述:R8C/2B 96+2/7 64LQFP 10X10 -40 TO +85 - Trays 制造商:Renesas Electronics Corporation 功能描述:IC MCU 16BIT 96KB FLASH 64LQFP |
| R5F212BASDXXXFA | 制造商:RENESAS 制造商全称:Renesas Technology Corp 功能描述:RENESAS MCU R8C FAMILY / R8C/2x SERIES |
| R5F212BASDXXXFP | 制造商:RENESAS 制造商全称:Renesas Technology Corp 功能描述:RENESAS MCU R8C FAMILY / R8C/2x SERIES |
发布紧急采购，3分钟左右您将得到回复。