- 您现在的位置：买卖IC网 > Datasheet目录354 > RDK-242 (Power Integrations)KIT REF DESIGN VG TOPSWITCH-JX Datasheet资料下载
参数资料
| 型号： | RDK-242 |
| 厂商： | Power Integrations |
| 文件页数： | 8/40页 |
| 文件大小： | 0K |
| 描述： | KIT REF DESIGN VG TOPSWITCH-JX |
| 标准包装： | 1 |
| 系列： | TOPSwitch®-JX |
| 主要目的： | AC/DC，主面和辅面 |
| 输出及类型： | 1，隔离 |
| 功率 - 输出： | 30W |
| 输出电压： | 12V |
| 电流 - 输出： | 2.5A |
| 输入电压： | 85 ~ 264VAC |
| 稳压器拓扑结构： | 回扫 |
| 频率 - 开关： | 132kHz |
| 板类型： | 完全填充 |
| 已供物品： | 板 |
| 已用 IC / 零件： | TOP266VG |
| 其它名称： | 596-1312 |
第1页第2页第3页第4页第5页第6页第7页当前第8页第9页第10页第11页第12页第13页第14页第15页第16页第17页第18页第19页第20页第21页第22页第23页第24页第25页第26页第27页第28页第29页第30页第31页第32页第33页第34页第35页第36页第37页第38页第39页第40页
TOP264-271
If the power supply is operating under heavy load or low input
line conditions when an open loop occurs, the output voltage
may not rise significantly. Under these conditions, a latching
shutdown will not occur until load or line conditions change.
Nevertheless, the operation provides the desired protection by
preventing significant rise in the output voltage when the line or
load conditions do change. Primary-side OVP protection with
the TOP264-271 in a typical application will prevent a nominal
12 V output from rising above approximately 20 V under open
loop conditions. If greater accuracy is required, a secondary
sensed OVP circuit is recommended.
Line Feed-Forward with DC MAX Reduction
The same resistor used for UV and OV also implements line voltage
feed-forward, which minimizes output line ripple and reduces
power supply output sensitivity to line transients. Note that for the
same CONTROL pin current, higher line voltage results in smaller
operating duty cycle. As an added feature, the maximum duty
cycle DC MAX is also reduced from 78% (typical) at a voltage slightly
lower than the UV threshold to 36% (typical) at the OV threshold.
DC MAX of 36% at high-line was chosen to ensure that the power
capability of the TOP264-271 is not restricted by this feature under
normal operation. TOP264-271 provides a better fit to the ideal
feed-forward by using two reduction slopes: -1% per m A for all bus
voltage less than 195 V (typical for 4 M W line impedance) and
-0.25% per m A for all bus voltage more than 195 V.
Voltage Monitor and External Current Limit Pin Table*
Remote ON/OFF
TOP264-271 can be turned on or off by controlling the current into
the VOLTAGE-MONITOR pin or out from the EXTERNAL CURRENT
LIMIT pin. In addition, the VOLTAGE-MONITOR pin has a 1 V
threshold comparator connected at its input. This voltage
threshold can also be used to perform remote ON/OFF control.
When a signal is received at the VOLTAGE-MONITOR pin or the
EXTERNAL CURRENT LIMIT pin to disable the output through
any of the pin functions such as OV, UV and remote ON/OFF,
TOP264-271 always completes its current switching cycle before
the output is forced off.
As seen above, the remote ON/OFF feature can also be used as
a standby or power switch to turn off the TOP264-271 and keep
it in a very low power consumption state for indefinitely long
periods. If the TOP264-271 is held in remote off state for long
enough time to allow the CONTROL pin to discharge to the
internal supply undervoltage threshold of 4.8 V (approximately
32 ms for a 47 m F CONTROL pin capacitance), the CONTROL
pin goes into the hysteretic mode of regulation. In this mode,
the CONTROL pin goes through alternate charge and discharge
cycles between 4.8 V and 5.8 V (see CONTROL pin operation
section above) and runs entirely off the high-voltage DC input,
but with very low power consumption (<100 mW typical at
230 VAC with X pin open). When the TOP264-271 is remotely
Figure Number
13
14
15
16
17
18
19
20
21
22
23
24
Three Terminal Operation
3
Line Undervoltage (UV)
Line Overvoltage (OV)
Line Feed-Forward (DC MAX )
3
3
3
3
3
3
3
3
3
3
3
3
3
3
Output Overvoltage Protection (OVP)
Overload Power Limiting (OPP)
3
3
External Current Limit
3
3
3
3
3
3
Remote ON/OFF
Device Reset
Fast AC Reset
AC Brown-Out
3
3
3
3
3
3
3
3
* This table is only a partial list of many VOLTAGE MONITOR and EXTERNAL CURRENT LIMIT Pin Configurations that are possible.
Table 2.
8
Rev. E 08/12
VOLTAGE MONITOR (V) Pin and EXTERNAL CURRENT LIMIT (X) Pin Configuration Options.
www.powerint.com
相关PDF资料 |
PDF描述 |
|---|---|
| RJCSE538001 | CONN MOD JACK 8P8C SMT R/A |
| RJE031882420 | CONN MOD JACK 8P/8C S-FLANGES |
| RJE051660310 | CONN MOD JACK 6P/6C UNSHIELDED |
| RJE051880110 | CONN MOD JACK 8/8 R/A UNSHIELDED |
| RJE051881310 | CONN MOD JACK 8P/8C SHIELDED |
相关代理商/技术参数 |
参数描述 |
|---|---|
| RDK-248 | 功能描述:LED 照明开发工具 UNIVERSAL PFC 180W HiperPFS KIT RoHS:否 制造商:Fairchild Semiconductor 产品:Evaluation Kits 用于:FL7732 核心: 电源电压:120V 系列: 封装: |
| RDK-249 | 功能描述:线性和开关式电源 HiperTFS Ref Des Kit 14.W Stby, 300W PS RoHS:否 制造商:TDK-Lambda 产品:Switching Supplies 开放式框架/封闭式:Enclosed 输出功率额定值:800 W 输入电压:85 VAC to 265 VAC 输出端数量:1 输出电压（通道 1）:20 V 输出电流（通道 1）:40 A 商用/医用: 输出电压（通道 2）: 输出电流（通道 2）: 安装风格:Rack 长度: 宽度: 高度: |
| RDK-251 | 功能描述:LED 照明开发工具 LinkSwitch-PL Ref Des Kit, 5W Dim RoHS:否 制造商:Fairchild Semiconductor 产品:Evaluation Kits 用于:FL7732 核心: 电源电压:120V 系列: 封装: |
| RDK-252 | 功能描述:电源管理IC开发工具 CAPZero Ref Des Kit CAPZero RoHS:否 制造商:Maxim Integrated 产品:Evaluation Kits 类型:Battery Management 工具用于评估:MAX17710GB 输入电压: 输出电压:1.8 V |
| RDK-257 | 功能描述:LED 照明开发工具 RefDesign 12W90-265V LinkSwitch-PH RoHS:否 制造商:Fairchild Semiconductor 产品:Evaluation Kits 用于:FL7732 核心: 电源电压:120V 系列: 封装: |
发布紧急采购，3分钟左右您将得到回复。