- 您现在的位置：买卖IC网 > PDF目录69323 > RS5C372A-E2 (RICOH COMPANY LTD) 0 TIMER(S), REAL TIME CLOCK, PDSO8 PDF资料下载
参数资料
| 型号： | RS5C372A-E2 |
| 厂商： | RICOH COMPANY LTD |
| 元件分类： | 时钟/数据恢复及定时提取 |
| 英文描述： | 0 TIMER(S), REAL TIME CLOCK, PDSO8 |
| 封装： | 0.65 MM PITCH, SSOP-8 |
| 文件页数： | 25/59页 |
| 文件大小： | 442K |
| 代理商： | RS5C372A-E2 |
第1页第2页第3页第4页第5页第6页第7页第8页第9页第10页第11页第12页第13页第14页第15页第16页第17页第18页第19页第20页第21页第22页第23页第24页当前第25页第26页第27页第28页第29页第30页第31页第32页第33页第34页第35页第36页第37页第38页第39页第40页第41页第42页第43页第44页第45页第46页第47页第48页第49页第50页第51页第52页第53页第54页第55页第56页第57页第58页第59页
RS5C372A/B
27
Cautions on Determining RP Resistance
(1) Voltage drop at RP due to sum of input current or output current at off conditions on each IC pin connect-
ed to the I
2C bus shall be adequately small.
(2) Rising time of each signal shall be kept short even when all capacity of the bus is driven.
(3) Current consumed in I
2C bus is small compared to the consumption current permitted for the entire sys-
tem.
When all ICs connected to I
2C bus are CMOS type, condition (1) may usually be ignored since input current
and off state output current is extremely small for the many CMOS type ICs.
Thus the maximum resistance of RP may be determined based on (2) while the minimum on (3) in most cas-
es.
In actual cases a resistor may be place between the bus and input/output pins of each IC to improve noise
margins in which case the RP minimum value may be determined by the resistance.
Consumption current in the bus to review (3) above may be expressed by the formula below:
Bus consumption current =
(Sum of input current and off state output current of all devices in stand-by mode)
× Bus stand-by duration
Bus stand-by duration + bus operation duration
+
Supply voltage
× bus operation duration × 2
RP resistance
× 2 × (bus stand-by duration + bus operation duration)
+
supply voltage
× bus capacity × charging/discharging times per unit time
Operation of “
× 2” in the second member denominator in the above formula is derived from assumption that
“L” duration of SDA and SCL pins are the half of bus operation duration. “
× 2” in the numerator of the same
member is because there are two pins of SDA and SCL. The third member, (charging/discharging times per
unit time) means number of transition from “H” to “L” of the signal line.
Calculation example is shown below:
Pull-up resistor (RP)=10k
, Bus capacity=50pF (both for SCL and SDA), VDD=3V
In as system with sum of input current and off state output current of each pin=0.1A, I
2C bus is used for
10ms every second while the rest of 990ms is in the stand-by mode. In this mode number of transitions of the
SCL pin from “H” to “L” state is 100 while SDA 50, every second.
Bus consumption current =
0.1A
× 990ms
990ms + 10ms
+
3V
× 10ms × 2
10k
× 2 × (990ms + 10ms)
+
3V
× 50pF × (100 + 50)
=
0.099A + 3.0A + 0.0225A = 3.12A
Generally, the second member of the above formula is larger enough than the first and the third members,
bus consumption current may be determined by the second member in many cases.
. .
相关PDF资料 |
PDF描述 |
|---|---|
| RT6224K-125 | 64-BIT, 125 MHz, RISC PROCESSOR, XMA100 |
| RT6224K-90 | 64-BIT, 90 MHz, RISC PROCESSOR, XMA100 |
| RT6224K-55 | 64-BIT, 55 MHz, RISC PROCESSOR, XMA100 |
| RT6226K-90 | 64-BIT, 90 MHz, RISC PROCESSOR, XMA100 |
| RT6226K-110/1024 | 64-BIT, 110 MHz, RISC PROCESSOR, XMA100 |
相关代理商/技术参数 |
参数描述 |
|---|---|
| RS5C372B | 制造商:RICOH 制造商全称:RICOH electronics devices division 功能描述:I2C-bus Serial Interface Real Time Clock (8pin SSOP) |
| RS5C372B-E1 | 制造商:RICOH 制造商全称:RICOH electronics devices division 功能描述:I2C-bus Serial Interface Real Time Clock (8pin SSOP) |
| RS5C372B-E2 | 制造商:RICOH 制造商全称:RICOH electronics devices division 功能描述:I2C-bus Serial Interface Real Time Clock (8pin SSOP) |
| RS5C373A | 制造商:未知厂家 制造商全称:未知厂家 功能描述:Real-Time Clock |
| RS5C4FC | 制造商:Dialight 功能描述: |
发布紧急采购，3分钟左右您将得到回复。