- 您现在的位置：买卖IC网 > PDF目录270895 > S29GL256N80TFIV10 (Spansion Inc.) MirrorBit Flash Family PDF资料下载
参数资料
| 型号： | S29GL256N80TFIV10 |
| 厂商： | Spansion Inc. |
| 英文描述： | MirrorBit Flash Family |
| 中文描述： | MirrorBit闪存系列 |
| 文件页数： | 76/110页 |
| 文件大小： | 2624K |
| 代理商： | S29GL256N80TFIV10 |
第1页第2页第3页第4页第5页第6页第7页第8页第9页第10页第11页第12页第13页第14页第15页第16页第17页第18页第19页第20页第21页第22页第23页第24页第25页第26页第27页第28页第29页第30页第31页第32页第33页第34页第35页第36页第37页第38页第39页第40页第41页第42页第43页第44页第45页第46页第47页第48页第49页第50页第51页第52页第53页第54页第55页第56页第57页第58页第59页第60页第61页第62页第63页第64页第65页第66页第67页第68页第69页第70页第71页第72页第73页第74页第75页当前第76页第77页第78页第79页第80页第81页第82页第83页第84页第85页第86页第87页第88页第89页第90页第91页第92页第93页第94页第95页第96页第97页第98页第99页第100页第101页第102页第103页第104页第105页第106页第107页第108页第109页第110页
68
S29GLxxxN MirrorBitTM Flash Family
27631A4 May 13, 2004
Adva nce
Inform at i o n
gram operation using the DQ7 or DQ6 status bits, just as in the standard word
program operation. Refer to the Write Operation Status section for more
information.
In the erase-suspend-read mode, the system can also issue the autoselect com-
mand sequence. Refer to the Autoselect Mode section and “Autoselect Command
Sequence” section on page 58 sections for details.
To resume the sector erase operation, the system must write the Erase Resume
command. The address of the erase-suspended sector is required when writing
this command. Further writes of the Resume command are ignored. Another
Erase Suspend command can be written after the chip has resumed erasing. It is
important to allow an intervalof at least 5 ns between Erase Resume and Erase
Suspend.
Lock Register Command Set Definitions
The Lock Register Command Set permits the user to one-time program the SecSi
Sector Protection Bit, Persistent Protection Mode Lock Bit, and Password Protec-
tion Mode Lock Bit. The Lock Register bits are all readable after an initial access
delay.
The Lock Register Command Set Entry command sequence must be issued
prior to any of the following commands listed, to enable proper command
execution.
Note that issuing the Lock Register Command Set Entry command disables
reads and writes for the flash memory.
Lock Register Program Command
Lock Register Read Command
The Lock Register Command Set Exit command must be issued after the ex-
ecution of the commands to reset the device to read mode. Otherwise the device
will hang. If this happens, the flash device must be reset. Please refer to RESET#
for more information. It is important to note that the device will be in either Per-
sistent Protection mode or Password Protection mode depending on the mode
selected prior to the device hang.
For either the SecSi Sector to be locked, or the device to be permanently set to
the Persistent Protection Mode or the Password Protection Mode, the associated
Lock Register bits must be programmed. Note that the Persistent Protection
Mode Lock Bit and Password Protection Mode Lock Bit can never be pro-
grammed together at the same time. If so, the Lock Register Program
operation will abort.
The Lock Register Command Set Exit command must be initiated to re-
enable reads and writes to the main memory.
Password Protection Command Set Definitions
The Password Protection Command Set permits the user to program the 64-bit
password, verify the programming of the 64-bit password, and then later unlock
the device by issuing the valid 64-bit password.
The Password Protection Command Set Entry command sequence must be
issued prior to any of the commands listed following to enable proper command
execution.
Note that issuing the Password Protection Command Set Entry command
disabled reads and writes the main memory.
相关PDF资料 |
PDF描述 |
|---|---|
| S29GL256N90TFIV10 | MirrorBit Flash Family |
| S29GL256N10TFIV10 | MirrorBit Flash Family |
| S29GL256N80FFIV10 | MirrorBit Flash Family |
| S29AL008D55TFNR11 | SSR OCMOS FET 350MA NO 8-DIP |
| S29AL008D70TFNR11 | 8 Megabit (1 M x 8-Bit/512 K x 16-Bit) CMOS 3.0 Volt-only Boot Sector Flash Memory |
相关代理商/技术参数 |
参数描述 |
|---|---|
| S29GL256N90FFIR10 | 制造商:Spansion 功能描述:Flash Mem Parallel 3.3V 256M-Bit 32M x 8/16M x 16 90ns 64-Pin Fortified BGA Tray |
| S29GL256N90FFIR22 | 制造商:Spansion 功能描述: |
| S29GL256N90TFIR10 | 制造商:Spansion 功能描述:NOR Flash Parallel 3.3V 256Mbit 32M/16M x 8bit/16bit 90ns 56-Pin TSOP Tray 制造商:Spansion 功能描述:Flash - NOR IC |
| S29GL256N90TFIR2 | 制造商:Spansion 功能描述: |
| S29GL256N90TFIR20 | 制造商:Spansion 功能描述:Flash Mem Parallel 3.3V 256M-Bit 32M x 8/16M x 16 90ns 56-Pin TSOP Tray 制造商:Spansion 功能描述:Flash - NOR IC |
发布紧急采购，3分钟左右您将得到回复。