参数资料
型号: SA58637BS
厂商: NXP Semiconductors N.V.
元件分类: 音频放大器
英文描述: 2 x 2.2 W BTL audio amplifier
封装: SA58637BS<SOT910-1 (HVQFN20)|<<http://www.nxp.com/packages/SOT910-1.html<1<Always Pb-free,;
文件页数: 20/22页
文件大小: 156K
代理商: SA58637BS
SA58637_1
NXP B.V. 2008. All rights reserved.
Product data sheet
Rev. 01 — 25 February 2008
7 of 22
NXP Semiconductors
SA58637
2
× 2.2 W BTL audio amplier
[1]
With a load connected at the outputs the quiescent current will increase, the maximum of this increase being equal to the DC output
offset voltage divided by RL.
[2]
The DC output voltage with respect to ground is approximately 0.5
× V
CC.
12. Dynamic characteristics
[1]
Gain of the amplier is 2
× (R2 / R1) in test circuit of Figure 3.
[2]
The noise output voltage is measured at the output in a frequency range from 20 Hz to 20 kHz (unweighted), with a source impedance
of RS =0 at the input.
[3]
Power supply rejection ratio is measured at the output with a source impedance of RS =0 at the input. The ripple voltage is a
sine wave with a frequency of 1 kHz and an amplitude of 100 mV (RMS), which is applied to the positive supply rail.
[4]
Power supply rejection ratio is measured at the output, with a source impedance of RS =0 at the input. The ripple voltage is a
sine wave with a frequency between 100 Hz and 20 kHz and an amplitude of 100 mV (RMS), which is applied to the positive supply rail.
[5]
Output voltage in mute position is measured with an input voltage of 1 V (RMS) in a bandwidth of 20 kHz, which includes noise.
VO
output voltage
2.2
-
V
VO(offset)
differential output voltage offset
-
50
mV
IIB
input bias current
pins INL+, INR+
-
500
nA
pins INL
, INR
-
500
nA
VMODE
voltage on pin MODE
operating
0
-
0.5
V
mute
1.5
-
VCC 1.5
V
standby
VCC 0.5
-
VCC
V
IMODE
current on pin MODE
0 V < VMODE <VCC
--
20
A
VSELECT
voltage on pin SELECT
both channels on
1.5
-
VCC 1.5
V
left channel on
VCC 0.5
-
VCC
V
right channel on
GND
-
0.5
V
II(SELECT)
input current on pin SELECT
VSELECT = 0 V
-
100
A
Table 7.
Static characteristics …continued
VCC =6V; Tamb =25 °C; RL =8 ; VMODE = 0 V; measured in test circuit Figure 3; unless otherwise specied.
Symbol
Parameter
Conditions
Min
Typ
Max
Unit
Table 8.
Dynamic characteristics
VCC =6V; Tamb =25 °C; RL =8 ; f = 1 kHz; VMODE = 0 V; measured in test circuit Figure 3; unless otherwise specied.
Symbol
Parameter
Conditions
Min
Typ
Max
Unit
Po
output power
THD+N = 10 %
1.2
1.5
-
W
THD+N = 0.5 %
0.9
1.1
-
W
THD+N = 10 %; VCC =9V;
application demo board
-
2.2
-
W
THD+N
total harmonic
distortion-plus-noise
Po = 0.5 W
-
0.15
0.3
%
Gv(cl)
closed-loop voltage gain
-
30
dB
Zi
differential input impedance
-
100
-
k
Vn(o)
output noise voltage
-
100
V
PSRR
power supply rejection ratio
1 kHz
50
--dB
100 Hz to 20 kHz
40
--dB
VO(mute)
mute output voltage
mute condition
-
200
V
αcs
channel separation
40
--dB
相关PDF资料
PDF描述
SA58670ABS 2.1 W-channel stereo class-D audio amplifier
SA58670BS 2.1 W-channel stereo class-D audio amplifier
SA58672TK 3.0 W mono class-D audio amplifier
SA58672UK 3.0 W mono class-D audio amplifier
SAA-50T-3 2 mm2, BRASS, TIN FINISH, FORK TERMINAL
相关代理商/技术参数
参数描述
SA58637BS,118 功能描述:音频放大器 DUAL 2.2W/CH. BTL RoHS:否 制造商:STMicroelectronics 产品:General Purpose Audio Amplifiers 输出类型:Digital 输出功率: THD + 噪声: 工作电源电压:3.3 V 电源电流: 最大功率耗散: 最大工作温度: 安装风格:SMD/SMT 封装 / 箱体:TQFP-64 封装:Reel
SA58637BS118 制造商:NXP Semiconductors 功能描述:IC AUDIO AMP AB 2.2W SON-20
SA58637BS-T 功能描述:音频放大器 DUAL 2.2W/CH. BTL AUDIO AMP RoHS:否 制造商:STMicroelectronics 产品:General Purpose Audio Amplifiers 输出类型:Digital 输出功率: THD + 噪声: 工作电源电压:3.3 V 电源电流: 最大功率耗散: 最大工作温度: 安装风格:SMD/SMT 封装 / 箱体:TQFP-64 封装:Reel
SA58640 制造商:PHILIPS 制造商全称:NXP Semiconductors 功能描述:Low-voltage mixer FM IF system
SA58640DK 功能描述:射频混合器 NB FM IF RECEIVER RoHS:否 制造商:NXP Semiconductors 频率范围: 转换损失——最大: 工作电源电压:6 V 最大工作温度:+ 85 C 最小工作温度:- 40 C 安装风格:Through Hole 封装 / 箱体:PDIP-8 封装:Tube