- 您现在的位置：买卖IC网 > PDF目录98078 > SC16C550IB48,128 (NXP SEMICONDUCTORS) 1 CHANNEL(S), 3M bps, SERIAL COMM CONTROLLER, PQFP48 PDF资料下载
参数资料
| 型号： | SC16C550IB48,128 |
| 厂商： | NXP SEMICONDUCTORS |
| 元件分类： | 微控制器/微处理器 |
| 英文描述： | 1 CHANNEL(S), 3M bps, SERIAL COMM CONTROLLER, PQFP48 |
| 封装： | 7 X 7 MM, 1.40 MM HEIGHT, PLASTIC, MS-026, SOT-313-2, LQFP-48 |
| 文件页数： | 51/52页 |
| 文件大小： | 639K |
| 代理商： | SC16C550IB48,128 |
第1页第2页第3页第4页第5页第6页第7页第8页第9页第10页第11页第12页第13页第14页第15页第16页第17页第18页第19页第20页第21页第22页第23页第24页第25页第26页第27页第28页第29页第30页第31页第32页第33页第34页第35页第36页第37页第38页第39页第40页第41页第42页第43页第44页第45页第46页第47页第48页第49页第50页当前第51页第52页
Philips Semiconductors
SC16C550
UART with 16-byte FIFO and IrDA encoder/decoder
Product data
Rev. 05 — 19 June 2003
8 of 52
9397 750 11619
Koninklijke Philips Electronics N.V. 2003. All rights reserved.
RCLK
10
5
9
I
Receiver clock. RCLK is the 16
× baud rate clock for the receiver
section of the UART.
IOR, IOR
24, 25
19, 20
21, 22
I
Read inputs. When either IOR or IOR is active (LOW or HIGH,
respectively) while the UART is selected, the CPU is allowed to read
status information or data from a selected UART register. Only one of
these inputs is required for the transfer of data during a read operation;
the other input should be tied to its inactive level (i.e., IOR tied LOW or
IOR tied HIGH).
RI
43
41
39
I
Ring indicator. RI is a modem status signal. Its condition can be
checked by reading bit 6 (RI) of the modem status register. Bit 2
(TERI) of the modem status register indicates that RI has transitioned
from a LOW to a HIGH level since the last read from the modem status
register. If the modem status interrupt is enabled when this transition
occurs, an interrupt is generated.
RTS
36
32
O
Request to send. When active, RTS informs the modem or data set
that the UART is ready to receive data. RTS is set to the active level by
setting the RTS modem control register bit and is set to the inactive
(HIGH) level either as a result of a Master Reset or during loop mode
operations or by clearing bit 1 (RTS) of the MCR. In the auto-RTS
mode, RTS is set to the inactive level by the receiver threshold control
logic.
RXRDY
322929
O
Receiver ready. Receiver direct memory access (DMA) signaling is
available with RXRDY. When operating in the FIFO mode, one of two
types of DMA signaling can be selected using the FIFO control register
bit 3 (FCR[3]). When operating in the 16C450 mode, only DMA
mode 0 is allowed. Mode 0 supports single-transfer DMA in which a
transfer is made between CPU bus cycles. Mode 1 supports
multi-transfer DMA in which multiple transfers are made continuously
until the receiver FIFO has been emptied. In DMA mode 0 (FCR0 = 0
or FCR0 = 1, FCR3 = 0), when there is at least one character in the
receiver FIFO or receiver holding register, RXRDY is active (LOW).
When RXRDY has been active but there are no characters in the FIFO
or holding register, RXRDY goes inactive (HIGH). In DMA mode 1
(FCR0 = 1, FCR3 = 1), when the trigger level or the time-out has been
reached, RXRDY goes active (LOW); when it has been active but there
are no more characters in the FIFO or holding register, it goes inactive
(HIGH).
RX
11
7
10
I
Serial data input. RX is serial data input from a connected
communications device.
TX
13
8
11
I
Serial data output. TX is composite serial data output to a connected
communication device. TX is set to the marking (HIGH) level as a
result of Master Reset.
TXRDY
272324
O
Transmitter ready. Transmitter DMA signaling is available with
TXRDY. When operating in the FIFO mode, one of two types of DMA
signaling can be selected using FCR[3]. When operating in the
16C450 mode, only DMA mode 0 is allowed. Mode 0 supports
single-transfer DMA in which a transfer is made between CPU bus
cycles. Mode 1 supports multi-transfer DMA in which multiple transfers
are made continuously until the transmit FIFO has been lled.
Table 2:
Pin description…continued
Symbol
Pin
Type
Description
PLCC44 LQFP48 DIP40
相关PDF资料 |
PDF描述 |
|---|---|
| SC16C654IB64,128 | 4 CHANNEL(S), 5M bps, SERIAL COMM CONTROLLER, PQFP64 |
| SC16C654IA68,512 | 4 CHANNEL(S), 5M bps, SERIAL COMM CONTROLLER, PQCC68 |
| SC18005CQ | SPECIALTY MICROPROCESSOR CIRCUIT, PQFP144 |
| SC18IS600IBS,151 | I2C BUS CONTROLLER, PQCC24 |
| SC18IS600IBS | I2C BUS CONTROLLER, PQCC24 |
相关代理商/技术参数 |
参数描述 |
|---|---|
| SC16C550IN40 | 制造商:PHILIPS 制造商全称:NXP Semiconductors 功能描述:Universal Asynchronous Receiver/Transmitter (UART) with 16-byte FIFO and infrared (IrDA) encoder/decoder |
| SC16C550IN40,112 | 功能描述:IC UART SINGLE W/FIFO 40-DIP RoHS:是 类别:集成电路 (IC) >> 接口 - UART（通用异步接收器/发送器） 系列:- 标准包装:250 系列:- 特点:* 通道数:2，DUART FIFO's:16 字节 规程:RS232，RS485 电源电压:2.25 V ~ 5.5 V 带并行端口:- 带自动流量控制功能:是 带IrDA 编码器/解码器:是 带故障启动位检测功能:是 带调制解调器控制功能:是 带CMOS:是 安装类型:表面贴装 封装/外壳:48-TQFP 供应商设备封装:48-TQFP（7x7） 包装:托盘 其它名称:XR16L2551IM-F-ND |
| SC16C554 | 制造商:PHILIPS 制造商全称:NXP Semiconductors 功能描述:Quad UART with 16-byte FIFO and infrared (IrDA) encoder/decoder |
| SC16C554B | 制造商:PHILIPS 制造商全称:NXP Semiconductors 功能描述:5 V, 3.3 V and 2.5 V quad UART, 5 Mbit/s (max.) with 16-byte FIFOs |
| SC16C554B_10 | 制造商:PHILIPS 制造商全称:NXP Semiconductors 功能描述:5 V, 3.3 V and 2.5 V quad UART, 5 Mbit/s (max.) with 16-byte FIFOs |
发布紧急采购，3分钟左右您将得到回复。