- 您现在的位置：买卖IC网 > PDF目录3765 > SC16IS752IPW,112 (NXP Semiconductors)IC UART DUAL 12C/SPI 28TSSOP PDF资料下载
参数资料
| 型号： | SC16IS752IPW,112 |
| 厂商： | NXP Semiconductors |
| 文件页数： | 28/60页 |
| 文件大小： | 0K |
| 描述： | IC UART DUAL 12C/SPI 28TSSOP |
| 产品培训模块： | Stand-Alone UARTs I²C Bus Fundamentals |
| 特色产品： | NXP - I2C Interface |
| 标准包装： | 51 |
| 特点： | 低电流 |
| 通道数： | 2，DUART |
| FIFO's： | 64 字节 |
| 规程： | RS232，RS485 |
| 电源电压： | 2.5V, 3.3V |
| 带自动流量控制功能： | 是 |
| 带IrDA 编码器/解码器： | 是 |
| 带故障启动位检测功能： | 是 |
| 带调制解调器控制功能： | 是 |
| 安装类型： | 表面贴装 |
| 封装/外壳： | 28-TSSOP（0.173"，4.40mm 宽） |
| 供应商设备封装： | 28-TSSOP |
| 包装： | 管件 |
| 产品目录页面： | 828 (CN2011-ZH PDF) |
| 配用： | 568-4000-ND - DEMO BOARD SPI/I2C TO DUAL UART 568-3510-ND - DEMO BOARD SPI/I2C TO UART |
| 其它名称： | 568-4016-5 935279292112 SC16IS752IPW SC16IS752IPW-ND |
第1页第2页第3页第4页第5页第6页第7页第8页第9页第10页第11页第12页第13页第14页第15页第16页第17页第18页第19页第20页第21页第22页第23页第24页第25页第26页第27页当前第28页第29页第30页第31页第32页第33页第34页第35页第36页第37页第38页第39页第40页第41页第42页第43页第44页第45页第46页第47页第48页第49页第50页第51页第52页第53页第54页第55页第56页第57页第58页第59页第60页
SC16IS752_SC16IS762
All information provided in this document is subject to legal disclaimers.
NXP B.V. 2012. All rights reserved.
Product data sheet
Rev. 9 — 22 March 2012
34 of 60
NXP Semiconductors
SC16IS752; SC16IS762
Dual UART with I2C-bus/SPI interface, 64-byte FIFOs, IrDA SIR
9.3 Auto RS-485
EFCR bit 0 is used to enable the RS-485 mode (multidrop or 9-bit mode). In this mode of
operation, a ‘master’ station transmits an address character followed by data characters
for the addressed ‘slave’ stations. The slave stations examine the received data and
interrupt the controller if the received character is an address character (parity bit = 1).
To use the auto RS-485 RTS mode the software would have to disable the hardware flow
control function.
9.3.1 Normal multidrop mode
The 9-bit mode in EFCR (bit 0) is enabled, but not Special Character Detect (EFR bit 5).
The receiver is set to Force Parity 0 (LCR[5:3] = 111) in order to detect address bytes.
With the receiver initially disabled, it ignores all the data bytes (parity bit = 0) until an
address byte is received (parity bit = 1). This address byte will cause the UART to set the
parity error. The UART will generate a line status interrupt (IER bit 2 must be set to ‘1’ at
this time), and at the same time puts this address byte in the RX FIFO. After the controller
examines the byte it must make a decision whether or not to enable the receiver; it should
enable the receiver if the address byte addresses its ID address, and must not enable the
receiver if the address byte does not address its ID address.
If the controller enables the receiver, the receiver will receive the subsequent data until
being disabled by the controller after the controller has received a complete message
from the ‘master’ station. If the controller does not disable the receiver after receiving a
message from the ‘master’ station, the receiver will generate a parity error upon receiving
another address byte. The controller then determines if the address byte addresses its ID
address, if it is not, the controller then can disable the receiver. If the address byte
addresses the ‘slave’ ID address, the controller take no further action; the receiver will
receive the subsequent data.
9.3.2 Auto address detection
If Special Character Detect is enabled (EFR[5] is set and XOFF2 contains the address
byte) the receiver will try to detect an address byte that matches the programmed
character in XOFF2. If the received byte is a data byte or an address byte that does not
match the programmed character in XOFF2, the receiver will discard these data. Upon
receiving an address byte that matches the XOFF2 character, the receiver will be
automatically enabled if not already enabled, and the address character is pushed into the
RX FIFO along with the parity bit (in place of the parity error bit). The receiver also
generates a line status interrupt (IER bit 2 must be set to 1 at this time). The receiver will
then receive the subsequent data from the ‘master’ station until being disabled by the
controller after having received a message from the ‘master’ station.
If another address byte is received and this address byte does not match XOFF2
character, the receiver will be automatically disabled and the address byte is ignored. If
the address byte matches XOFF2 character, the receiver will put this byte in the RX FIFO
along with the parity bit in the parity error bit (LSR[2]).
相关PDF资料 |
PDF描述 |
|---|---|
| SC16C850IBS,151 | IC UART SGL-CH 3.3V 32-HVQFN |
| SC16IS760IPW,112 | IC UART 64BYTE 24TSSOP |
| FT2232HL-REEL | IC USB HS DUAL UART/FIFO 64-LQFP |
| ATMEGA168P-20AUR | MCU AVR 16K FLASH 20MHZ 32-TQFP |
| SC16IS750IPW,112 | IC UART I2C/SPI 24-TSSOP |
相关代理商/技术参数 |
参数描述 |
|---|---|
| SC16IS752IPW128 | 制造商:NXP Semiconductors 功能描述: |
| SC16IS752IPW-F | 功能描述:UART 接口集成电路 I2C/SPI-UARTBRIDGE W/IRDA AND GPIO RoHS:否 制造商:Texas Instruments 通道数量:2 数据速率:3 Mbps 电源电压-最大:3.6 V 电源电压-最小:2.7 V 电源电流:20 mA 最大工作温度:+ 85 C 最小工作温度:- 40 C 封装 / 箱体:LQFP-48 封装:Reel |
| SC16IS752IPW-S | 功能描述:IC UART DUAL I2C/SPI 28-TSSOP RoHS:是 类别:集成电路 (IC) >> 接口 - UART（通用异步接收器/发送器） 系列:- 标准包装:250 系列:- 特点:* 通道数:2，DUART FIFO's:16 字节 规程:RS232，RS485 电源电压:2.25 V ~ 5.5 V 带并行端口:- 带自动流量控制功能:是 带IrDA 编码器/解码器:是 带故障启动位检测功能:是 带调制解调器控制功能:是 带CMOS:是 安装类型:表面贴装 封装/外壳:48-TQFP 供应商设备封装:48-TQFP（7x7） 包装:托盘 其它名称:XR16L2551IM-F-ND |
| SC16IS752IPW-T | 功能描述:IC UART DUAL I2C/SPI 28-TSSOP RoHS:是 类别:集成电路 (IC) >> 接口 - UART（通用异步接收器/发送器） 系列:- 标准包装:250 系列:- 特点:* 通道数:2，DUART FIFO's:16 字节 规程:RS232，RS485 电源电压:2.25 V ~ 5.5 V 带并行端口:- 带自动流量控制功能:是 带IrDA 编码器/解码器:是 带故障启动位检测功能:是 带调制解调器控制功能:是 带CMOS:是 安装类型:表面贴装 封装/外壳:48-TQFP 供应商设备封装:48-TQFP（7x7） 包装:托盘 其它名称:XR16L2551IM-F-ND |
| SC16IS760 | 制造商:PHILIPS 制造商全称:NXP Semiconductors 功能描述:Single UART with I2C-bus/SPI interface, 64 bytes of transmit and receive FIFOs, IrDA SIR built-in support |
发布紧急采购，3分钟左右您将得到回复。