参数资料
型号: SC16IS752IPW,112
厂商: NXP Semiconductors
文件页数: 52/60页
文件大小: 0K
描述: IC UART DUAL 12C/SPI 28TSSOP
产品培训模块: Stand-Alone UARTs
I²C Bus Fundamentals
特色产品: NXP - I2C Interface
标准包装: 51
特点: 低电流
通道数: 2,DUART
FIFO's: 64 字节
规程: RS232,RS485
电源电压: 2.5V, 3.3V
带自动流量控制功能:
带IrDA 编码器/解码器:
带故障启动位检测功能:
带调制解调器控制功能:
安装类型: 表面贴装
封装/外壳: 28-TSSOP(0.173",4.40mm 宽)
供应商设备封装: 28-TSSOP
包装: 管件
产品目录页面: 828 (CN2011-ZH PDF)
配用: 568-4000-ND - DEMO BOARD SPI/I2C TO DUAL UART
568-3510-ND - DEMO BOARD SPI/I2C TO UART
其它名称: 568-4016-5
935279292112
SC16IS752IPW
SC16IS752IPW-ND
SC16IS752_SC16IS762
All information provided in this document is subject to legal disclaimers.
NXP B.V. 2012. All rights reserved.
Product data sheet
Rev. 9 — 22 March 2012
56 of 60
NXP Semiconductors
SC16IS752; SC16IS762
Dual UART with I2C-bus/SPI interface, 64-byte FIFOs, IrDA SIR
For further information on temperature profiles, refer to Application Note AN10365
“Surface mount reflow soldering description”.
18. Appendix
18.1 Errata for Rev. E added 12 August 2011
18.1.1 IrDA wake-up
In Rev. D, the UART cannot wake up through RX pin once the UART is put to sleep by the
host.
18.1.2 Clearing of RX FIFO overflow
In Rev. D, once the receive FIFO overflows, the receive FIFO cannot be cleared with FIFO
reset command if the UART is continuously receiving data.
18.1.3 Interrupt priority encoder
When the edge of the IOR signal (an internal signal that reads IIR register) comes close to
the X1 clock that generates the interrupt, the value of the Interrupt Indication Register (IIR)
might not be correct. This issue might occur if the X1 clock is very slow and the host read
operation is very fast in response to the interrupt from the UART.
18.1.4 Time-out interrupt
If the host reads the receive FIFO at the at the same time as a time-out interrupt condition
happens, the host might read 0xCC (time-out) in the Interrupt Indication Register (IIR), but
bit 0 of the Line Status Register (LSR) is not set (means there is not data in the
receive FIFO). This is a conflict of the receive FIFO status when IIR = 0xCC (time-out), it
indicates that there are data in the receive FIFO, but LSR bit 0 = 0 indicates otherwise.
MSL: Moisture Sensitivity Level
Fig 39. Temperature profiles for large and small components
001aac844
temperature
time
minimum peak temperature
= minimum soldering temperature
maximum peak temperature
= MSL limit, damage level
peak
temperature
相关PDF资料
PDF描述
SC16C850IBS,151 IC UART SGL-CH 3.3V 32-HVQFN
SC16IS760IPW,112 IC UART 64BYTE 24TSSOP
FT2232HL-REEL IC USB HS DUAL UART/FIFO 64-LQFP
ATMEGA168P-20AUR MCU AVR 16K FLASH 20MHZ 32-TQFP
SC16IS750IPW,112 IC UART I2C/SPI 24-TSSOP
相关代理商/技术参数
参数描述
SC16IS752IPW128 制造商:NXP Semiconductors 功能描述:
SC16IS752IPW-F 功能描述:UART 接口集成电路 I2C/SPI-UARTBRIDGE W/IRDA AND GPIO RoHS:否 制造商:Texas Instruments 通道数量:2 数据速率:3 Mbps 电源电压-最大:3.6 V 电源电压-最小:2.7 V 电源电流:20 mA 最大工作温度:+ 85 C 最小工作温度:- 40 C 封装 / 箱体:LQFP-48 封装:Reel
SC16IS752IPW-S 功能描述:IC UART DUAL I2C/SPI 28-TSSOP RoHS:是 类别:集成电路 (IC) >> 接口 - UART(通用异步接收器/发送器) 系列:- 标准包装:250 系列:- 特点:* 通道数:2,DUART FIFO's:16 字节 规程:RS232,RS485 电源电压:2.25 V ~ 5.5 V 带并行端口:- 带自动流量控制功能:是 带IrDA 编码器/解码器:是 带故障启动位检测功能:是 带调制解调器控制功能:是 带CMOS:是 安装类型:表面贴装 封装/外壳:48-TQFP 供应商设备封装:48-TQFP(7x7) 包装:托盘 其它名称:XR16L2551IM-F-ND
SC16IS752IPW-T 功能描述:IC UART DUAL I2C/SPI 28-TSSOP RoHS:是 类别:集成电路 (IC) >> 接口 - UART(通用异步接收器/发送器) 系列:- 标准包装:250 系列:- 特点:* 通道数:2,DUART FIFO's:16 字节 规程:RS232,RS485 电源电压:2.25 V ~ 5.5 V 带并行端口:- 带自动流量控制功能:是 带IrDA 编码器/解码器:是 带故障启动位检测功能:是 带调制解调器控制功能:是 带CMOS:是 安装类型:表面贴装 封装/外壳:48-TQFP 供应商设备封装:48-TQFP(7x7) 包装:托盘 其它名称:XR16L2551IM-F-ND
SC16IS760 制造商:PHILIPS 制造商全称:NXP Semiconductors 功能描述:Single UART with I2C-bus/SPI interface, 64 bytes of transmit and receive FIFOs, IrDA SIR built-in support