参数资料
型号: SI4704-D50-GM
厂商: Silicon Laboratories Inc
文件页数: 18/34页
文件大小: 0K
描述: IC FM RADIO RECEIVER ADV 20-QFN
标准包装: 490
频率: 64MHz ~ 108MHz
调制或协议: FM
应用: 通用
数据接口: PCB,表面贴装
天线连接器: PCB,表面贴装
电源电压: 2.7 V ~ 5.5 V
工作温度: -20°C ~ 85°C
封装/外壳: 20-UFQFN 裸露焊盘
供应商设备封装: 20-QFN(3x3)
包装: 托盘
Si4704/05-D50
The Si4704/05 performs much of the FM demodulation
digitally to achieve high fidelity, optimal performance
versus power consumption, and flexibility of design. The
on-board DSP provides unmatched pilot rejection,
selectivity, and optimum sound quality. The integrated
micro-controller offers both the manufacturer and the
end-user unmatched programmability and flexibility in
the listening experience.
4.2. FM Receiver
The Si4704/05 FM receiver is based on the proven
Si4700/01/02/03/04/05 FM radio receiver. The part
leverages Silicon Laboratories' proven and patented FM
broadcast radio receiver digital architecture, delivering
excellent RF performance and interference rejection.
The proven digital techniques provide good sensitivity in
weak signal environments while allowing superb
selectivity and inter-modulation immunity in strong signal
environments.
The part supports the worldwide FM broadcast band (64
to 108 MHz) with channel spacings of 50–200 kHz. The
low-IF architecture utilizes a single converter stage and
digitizes the signal using a high-resolution analog-to-
digital converter. The audio output can be directed
either to an external headphone amplifier via analog
in/out or to other system ICs through digital audio
interface (I 2 S) (Si4705 only).
4.3. Stereo Audio Processing
The output of the FM demodulator is a stereo
multiplexed (MPX) signal. The MPX standard was
developed in 1961, and is used worldwide. Today's
MPX signal format consists of left + right (L+R) audio,
left – right (L–R) audio, a 19 kHz pilot tone, and
RDS/RBDS data as shown in Figure 8.
Mono Audio
4.3.1. Stereo Decoder
The Si4704/05 integrated stereo decoder automatically
decodes the MPX signal using DSP techniques. The 0
to 15 kHz (L+R) signal is the mono output of the FM
tuner. Stereo is generated from the (L+R), (L–R), and a
19 kHz pilot tone. The pilot tone is used as a reference
to recover the (L–R) signal. Output left and right
channels are obtained by adding and subtracting the
(L+R) and (L–R) signals, respectively.
4.3.2. Stereo-Mono Blending
Adaptive noise suppression is employed to gradually
combine the stereo left and right audio channels to a
mono (L+R) audio signal as the signal quality degrades
to maintain optimum sound fidelity under varying
reception conditions. Three metrics, received signal
strength indicator (RSSI), signal-to-noise ratio (SNR),
and multipath interference, are monitored
simultaneously in forcing a blend from stereo to mono.
The metric which reflects the minimum signal quality
takes precedence and the signal is blended
appropriately.
All three metrics have programmable stereo/mono
thresholds and attack/release rates detailed in “AN332:
Si47xx Programming Guide.” If a metric falls below its
mono threshold, the signal is blended from stereo to full
mono. If all metrics are above their respective stereo
thresholds, then no action is taken to blend the signal. If
a metric falls between its mono and stereo thresholds,
then the signal is blended to the level proportional to the
metric’s value between its mono and stereo thresholds,
with an associated attack and release rate.
Stereo/mono status can be monitored with the
FM_RSQ_STATUS command.
4.4. Received Signal Qualifiers
The quality of a tuned signal can vary depending on
many factors including environmental conditions, time of
day, and position of the antenna. To adequately manage
the audio output and avoid unpleasant audible effects to
Left + Right
Stereo
Pilot
Stereo Audio
Left - Right
RDS/
RBDS
the end-user, the Si4704/05-D50 monitors and provides
indicators of the signal quality, allowing the host
processor to perform additional processing if required
by the customer. The Si4704/05-D50 monitors signal
0
15 19 23 38
Frequency (kHz)
53
57
quality metrics including RSSI, SNR, and multipath
interference on FM signals. These metrics are used to
optimize signal processing and are also reported to the
Figure 8. MPX Signal Spectrum
host processor. The signal processing algorithms can
use either Silicon Labs'
optimized settings
(recommended) or be customized to modify
performance.
18
Rev. 1.0
相关PDF资料
PDF描述
ZVN4206GVTA MOSFET N-CH 60V 1A SOT223
IXTP80N10T MOSFET N-CH 100V 80A TO-220
IRF3711ZSPBF MOSFET N-CH 20V 92A D2PAK
SI4737-C40-GMR IC RX AM/FM/WB RDS/RBDS 20UQFN
SI4737-C40-GUR IC RX AM/FM/WB RDS/RBDS 24SSOP
相关代理商/技术参数
参数描述
Si4704-D50-GMR 功能描述:射频接收器 BRDCAST FM/AUXIN RADIO TUNER RoHS:否 制造商:Skyworks Solutions, Inc. 类型:GPS Receiver 封装 / 箱体:QFN-24 工作频率:4.092 MHz 工作电源电压:3.3 V 封装:Reel
SI4704-D60-GM 功能描述:IC FM RADIO TUNER 20-QFN RoHS:是 类别:RF/IF 和 RFID >> RF 接收器 系列:- 产品培训模块:Lead (SnPb) Finish for COTS 产品变化通告:Product Discontinuation 09/Jan/2012 标准包装:50 系列:* 频率:850MHz ~ 2.175GHz 灵敏度:- 数据传输率 - 最大:- 调制或协议:- 应用:* 电流 - 接收:* 数据接口:PCB,表面贴装 存储容量:- 天线连接器:PCB,表面贴装 特点:- 电源电压:4.75 V ~ 5.25 V 工作温度:0°C ~ 85°C 封装/外壳:40-WFQFN 裸露焊盘 供应商设备封装:40-TQFN-EP(6x6) 包装:托盘
Si4704-D60-GMR 功能描述:射频接收器 BRDCAST FM/AUXIN RADIO TUNER RoHS:否 制造商:Skyworks Solutions, Inc. 类型:GPS Receiver 封装 / 箱体:QFN-24 工作频率:4.092 MHz 工作电源电压:3.3 V 封装:Reel
SI4704-D60-GU 功能描述:IC FM RADIO TUNER 24SSOP RoHS:是 类别:RF/IF 和 RFID >> RF 接收器 系列:- 产品培训模块:Lead (SnPb) Finish for COTS 产品变化通告:Product Discontinuation 09/Jan/2012 标准包装:50 系列:* 频率:850MHz ~ 2.175GHz 灵敏度:- 数据传输率 - 最大:- 调制或协议:- 应用:* 电流 - 接收:* 数据接口:PCB,表面贴装 存储容量:- 天线连接器:PCB,表面贴装 特点:- 电源电压:4.75 V ~ 5.25 V 工作温度:0°C ~ 85°C 封装/外壳:40-WFQFN 裸露焊盘 供应商设备封装:40-TQFN-EP(6x6) 包装:托盘
SI4704-D62-GM 制造商:Silicon Laboratories Inc 功能描述:CONSUMER ELECTRONICS FM + AUXIN RECEIVER - Trays 制造商:Silicon Laboratories Inc 功能描述:IC FM RADIO RECEIVER 20QFN