- 您现在的位置：买卖IC网 > PDF目录9578 > SI5315A-C-GMR (Silicon Laboratories Inc)IC CLK MULT 8KHZ-644.53MHZ 36QFN PDF资料下载
参数资料
| 型号： | SI5315A-C-GMR |
| 厂商： | Silicon Laboratories Inc |
| 文件页数： | 22/54页 |
| 文件大小： | 0K |
| 描述： | IC CLK MULT 8KHZ-644.53MHZ 36QFN |
| 应用说明： | SI5315/17 Crystal Selection AppNote |
| 标准包装： | 250 |
| 系列： | DSPLL® |
| 类型： | 时钟/频率倍增器，抖动衰减器，多路复用器 |
| PLL： | 无 |
| 主要目的： | 以太网，SONET/SDH/PDH，电信 |
| 输入： | CML，CMOS，LVDS，LVPECL |
| 输出： | CML，CMOS，LVDS，LVPECL |
| 电路数： | 1 |
| 比率 - 输入:输出： | 2:2 |
| 差分 - 输入:输出： | 是/是 |
| 频率 - 最大： | 644.53MHz |
| 电源电压： | 1.71 V ~ 3.63 V |
| 工作温度： | -40°C ~ 85°C |
| 安装类型： | 表面贴装 |
| 封装/外壳： | 36-VFQFN 裸露焊盘 |
| 供应商设备封装： | 36-QFN（6x6） |
| 包装： | 带卷 (TR) |
第1页第2页第3页第4页第5页第6页第7页第8页第9页第10页第11页第12页第13页第14页第15页第16页第17页第18页第19页第20页第21页当前第22页第23页第24页第25页第26页第27页第28页第29页第30页第31页第32页第33页第34页第35页第36页第37页第38页第39页第40页第41页第42页第43页第44页第45页第46页第47页第48页第49页第50页第51页第52页第53页第54页
Si5315
Rev. 1.0
29
5.2. PLL Self-Calibration
An internal self-calibration (ICAL) is performed before operation to optimize loop parameters and jitter
performance. While the self-calibration is being performed, the DSPLL is being internally controlled by the self-
calibration state machine. The LOL alarm will be active during ICAL. The self-calibration time tLOCKHW is given in
Any of the following events will trigger a self-calibration:
Power-on-reset (POR)
Release of the external reset pin RST (transition of RST from 0 to 1)
Change in FRQSEL, FRQTBL, BWSEL, or XTAL/CLOCK pins
Internal DSPLL registers out-of-range, indicating the need to relock the DSPLL
In any of the above cases, an internal self-calibration will be initiated if a valid input clock exists (no input alarm)
and is selected as the active clock at that time. The external crystal or reference clock must also be present for the
self-calibration to begin. If valid clocks are not present, the self-calibration state machine will wait until they appear,
at which time the calibration will start. An output clock will be active while waiting for a valid input clock. The output
clock frequency is based on the VCO range determine by FRQSEL and FRQTBL settings. This output clock will
vary by ±20%. If no output clock is desired prior to an ICAL, then the SFOUT pins should be kept at LM for
1.2 seconds until the output clock is stable.
After a successful self-calibration has been performed with a valid input clock, no subsequent self calibrations are
performed unless one of the above conditions are met. If the input clock is lost following self-calibration, the device
enters holdover mode. When the input clock returns, the device relocks to the input clock without performing a self-
calibration.
5.2.1. Input Clock Stability during Internal Self-Calibration
An exit from reset must occur when the selected CKINn clock is stable in frequency with a frequency value that is
within the device operating range. The other CKINs must also either be stable in frequency or squelched during a
reset.
5.2.2. Self-Calibration caused by Changes in Input Frequency
If the selected CKINn varies by 500 ppm or more in frequency since the last calibration, the device may initiate a
self-calibration.
5.2.3. Device Reset
Upon powerup, the device internally executes a power-on-reset (POR) which resets the internal device logic. The
pin RST can also be used to initiate a reset. The device stays in this state until a valid CKINn is present, when it
then performs a PLL Self-Calibration (See 5.2. "PLL Self-Calibration”).
5.2.4. Recommended Reset Guidelines
Follow the recommended RESET guidelines in Table 10 when reset should be applied to a device.
Table 10. Si5315 Pins and Reset
Pin #
Si5315 Pin Name
Must Reset after Changing
2FRQTBL
Yes
11
XTAL/CLOCK
Yes
22
BWSEL0
Yes
23
BWSEL1
Yes
24
FRQSEL0
Yes
25
FRQSEL1
Yes
26
FRQSEL2
Yes
27
FRQSEL3
Yes
相关PDF资料 |
PDF描述 |
|---|---|
| VE-2NT-MY-S | CONVERTER MOD DC/DC 6.5V 50W |
| VE-B3W-IU | CONVERTER MOD DC/DC 5.5V 200W |
| VE-B3T-IU | CONVERTER MOD DC/DC 6.5V 200W |
| VE-2NR-MY-S | CONVERTER MOD DC/DC 7.5V 50W |
| VE-B3P-IU | CONVERTER MOD DC/DC 13.8V 200W |
相关代理商/技术参数 |
参数描述 |
|---|---|
| Si5315B-C-GM | 功能描述:时钟发生器及支持产品 Pin-Prgrmmbl SyncE Clck Mlt/Jttr Attntr RoHS:否 制造商:Silicon Labs 类型:Clock Generators 最大输入频率:14.318 MHz 最大输出频率:166 MHz 输出端数量:16 占空比 - 最大:55 % 工作电源电压:3.3 V 工作电源电流:1 mA 最大工作温度:+ 85 C 安装风格:SMD/SMT 封装 / 箱体:QFN-56 |
| SI5315B-C-GMR | 功能描述:时钟发生器及支持产品 Pin-Ctrl SyncE Clk Xplier/Jitt Attn 2/2 RoHS:否 制造商:Silicon Labs 类型:Clock Generators 最大输入频率:14.318 MHz 最大输出频率:166 MHz 输出端数量:16 占空比 - 最大:55 % 工作电源电压:3.3 V 工作电源电流:1 mA 最大工作温度:+ 85 C 安装风格:SMD/SMT 封装 / 箱体:QFN-56 |
| SI5315-C | 制造商:AUK 制造商全称:AUK corp 功能描述:IRED |
| SI5315-C(B) | 制造商:AUK 制造商全称:AUK corp 功能描述:IRED |
| SI5315-C_1 | 制造商:AUK 制造商全称:AUK corp 功能描述:IRED |
发布紧急采购，3分钟左右您将得到回复。