- 您现在的位置：买卖IC网 > PDF目录4254 > SST25VF010A-33-4I-ZAE (Microchip Technology)IC FLASH SER 1MB 33MHZ SPI 8CSP PDF资料下载
参数资料
| 型号： | SST25VF010A-33-4I-ZAE |
| 厂商： | Microchip Technology |
| 文件页数： | 13/28页 |
| 文件大小： | 0K |
| 描述： | IC FLASH SER 1MB 33MHZ SPI 8CSP |
| 标准包装： | 3,000 |
| 系列： | SST25 |
| 格式 - 存储器： | 闪存 |
| 存储器类型： | FLASH |
| 存储容量： | 1M (128K x 8) |
| 速度： | 33MHz |
| 接口： | SPI 串行 |
| 电源电压： | 2.7 V ~ 3.6 V |
| 工作温度： | -40°C ~ 85°C |
| 封装/外壳： | 8-UFBGA，CSPBGA |
| 供应商设备封装： | 8-CSP |
| 包装： | 管件 |
第1页第2页第3页第4页第5页第6页第7页第8页第9页第10页第11页第12页当前第13页第14页第15页第16页第17页第18页第19页第20页第21页第22页第23页第24页第25页第26页第27页第28页
1 Mbit SPI Serial Flash
A Microchip Technology Company
SST25VF010A
Data Sheet
Auto Address Increment (AAI) Program
The AAI program instruction allows multiple bytes of data to be programmed without re-issuing the
next sequential address location. This feature decreases total programming time when the entire mem-
ory array is to be programmed. An AAI program instruction pointing to a protected memory area will be
ignored. The selected address range must be in the erased state (FFH) when initiating an AAI program
instruction.
Prior to any write operation, the Write-Enable (WREN) instruction must be executed. The AAI program
instruction is initiated by executing an 8-bit command, AFH, followed by address bits [A 23 -A 0 ]. Follow-
ing the addresses, the data is input sequentially from MSB (bit 7) to LSB (bit 0). CE# must be driven
high before the AAI program instruction is executed. The user must poll the BUSY bit in the software
status register or wait T BP for the completion of each internal self-timed Byte-Program cycle. Once the
device completes programming byte, the next sequential address may be program, enter the 8-bit
command, AFH, followed by the data to be programmed. When the last desired byte had been pro-
grammed, execute the Write-Disable (WRDI) instruction, 04H, to terminate AAI. After execution of the
WRDI command, the user must poll the Status register to ensure the device completes programming.
See Figure 7 for AAI programming sequence.
There is no wrap mode during AAI programming; once the highest unprotected memory address is
reached, the device will exit AAI operation and reset the Write-Enable-Latch bit (WEL = 0).
CE#
T BP
T B P
MODE 3
0 1 2 3 4 5 6 7 8
15 16
23 24
31 32 33 34 35 36 37 38 39
0 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15
0 1
SCK
MODE 0
SI
AF
A[23:16] A[15:8]
A[7:0]
Data Byte 1
AF
Data Byte 2
T BP
CE#
SCK
0 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15
0 1 2 3 4 5 6 7
0 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15
SI
AF
Last Data Byte
04
05
SO
Write Disable (WRDI)
Instruction to terminate
AAI Operation
Read Status Register (RDSR)
Instruction to verify end of
AAI Operation
D OUT
1265 F07.0
Figure 7: Auto Address Increment (AAI) Program Sequence
?2011 Silicon Storage Technology, Inc.
13
S725081A
10/11
相关PDF资料 |
PDF描述 |
|---|---|
| 2-829261-2 | CONN D-SUB HD FEMALE SCREW LOCK |
| RCB110DHAN | CONN EDGECARD 220PS R/A .050 DIP |
| 24LC128T-E/MS | IC EEPROM 128KBIT 400KHZ 8MSOP |
| 24LC128-E/MS | IC EEPROM 128KBIT 400KHZ 8MSOP |
| 25LC640AT-E/MNY | IC EEPROM 64KBIT 10MHZ 8TDFN |
相关代理商/技术参数 |
参数描述 |
|---|---|
| SST25VF016B | 制造商:SST 制造商全称:Silicon Storage Technology, Inc 功能描述:16 Mbit SPI Serial Flash |
| SST25VF016B_10 | 制造商:SST 制造商全称:Silicon Storage Technology, Inc 功能描述:16 Mbit SPI Serial Flash |
| SST25VF016B_11 | 制造商:SST 制造商全称:Silicon Storage Technology, Inc 功能描述:16 Mbit SPI Serial Flash |
| SST25VF016B_13 | 制造商:SST 制造商全称:Silicon Storage Technology, Inc 功能描述:16 Mbit SPI Serial Flash |
| SST25VF016B-25-4C-UA | 制造商:Microchip Technology Inc 功能描述:2.7V TO 3.6V 16MBIT SPI SERIAL FLASH - Gel-pak, waffle pack, wafer, diced wafer on film |
发布紧急采购，3分钟左右您将得到回复。