参数资料
型号: SST89V516RD-33-C-PI
厂商: SILICON STORAGE TECHNOLOGY INC
元件分类: 微控制器/微处理器
英文描述: 8-BIT, FLASH, 33 MHz, MICROCONTROLLER, PDIP40
封装: PLASTIC, MS-011AC, DIP-40
文件页数: 32/80页
文件大小: 934K
代理商: SST89V516RD-33-C-PI
38
Data Sheet
FlashFlex51 MCU
SST89E516RD2 / SST89E516RD
SST89V516RD2 / SST89V516RD
2005 Silicon Storage Technology, Inc.
S71273-01-000
3/05
There are no IAP counterparts for the external host com-
mands Select-Block0 and Select-Block1.
4.2.5 Polling
A command that uses the polling method to detect flash
operation completion should poll on the FLASH_BUSY bit
(SFST[2]). When FLASH_BUSY de-asserts (logic 0), the
device is ready for the next operation.
MOVC instruction may also be used for verification of the
Programming and Erase operation of the flash memory.
MOVC instruction will fail if it is directed at a flash block that
is still busy.
4.2.6 Interrupt Termination
If interrupt termination is selected, (SFCM[7] is set), then
an interrupt (INT1) will be generated to indicate flash opera-
tion completion. Under this condition, the INT1 becomes an
internal interrupt source. The INT1# pin can now be used
as a general purpose port pin and it cannot be the source
of External Interrupt 1 during in-application programming.
In order to use an interrupt to signal flash operation termi-
nation. EX1 and EA bits of IE register must be set. The IT1
bit of TCON register must also be set for edge trigger
detection.
.
Note: DISIAPL pin in PLCC or TQFP will also disable IAP commands if it is externally pulled low when reset.
TABLE
4-3: IAP COMMANDS1
1. SFCF[6]=1 enables IAP commands; SFCF[6]=0 disables IAP commands.
Operation
SFCM [6:0]2
2. Interrupt/Polling enable for flash operation completion
SFCM[7] = 1: Interrupt enable for flash operation completion
0: polling enable for flash operation completion
SFDT [7:0]
SFAH [7:0]
SFAL [7:0]
Chip-Erase3
3. Chip-Erase only functions in IAP mode when EA#=0 (external memory execution) and device is not in level 4 locking.
01H
55H
X4
4. X can be VIL or VIH, but no other value.
X
Block-Erase5
5. Refer to Table 4-2 for address resolution
0DH
55H
AH
X
Sector-Erase5
0BH
X
AH6
6. AH = Address high order byte
AL7
7. AL = Address low order byte
Byte-Program5
0EH
DI8
8. DI = Data Input, DO = Data Output, all other values are in hex.
AH
AL
Byte-Verify (Read)5
0CH
DO8
AH
AL
Prog-SB19
9. Instruction must be located in Block 1 or external code memory.
0FH
AAH
X
03H
AAH
X
05H
AAH
X
09H
AAH
5AH
X
Enable-Clock-Double9
08H
AAH
55H
X
T4-3.0 1273
相关PDF资料
PDF描述
SST89V516RD-33-I-PIE 8-BIT, FLASH, 33 MHz, MICROCONTROLLER, PDIP40
SST89E516RD-40-I-PIE 8-BIT, FLASH, 40 MHz, MICROCONTROLLER, PDIP40
SST89V554A-33-C-TQJ 8-BIT, FLASH, 33 MHz, MICROCONTROLLER, PQFP44
SST89E554A-40-C-NJ 8-BIT, FLASH, 40 MHz, MICROCONTROLLER, PQCC44
SST89E554A-40-I-TQJ 8-BIT, FLASH, 40 MHz, MICROCONTROLLER, PQFP44
相关代理商/技术参数
参数描述
SST89V516RD-33-C-PIE 功能描述:8位微控制器 -MCU 8-Bit 64K+8K Flash 33MHz 3/16-Bit Timer RoHS:否 制造商:Silicon Labs 核心:8051 处理器系列:C8051F39x 数据总线宽度:8 bit 最大时钟频率:50 MHz 程序存储器大小:16 KB 数据 RAM 大小:1 KB 片上 ADC:Yes 工作电源电压:1.8 V to 3.6 V 工作温度范围:- 40 C to + 105 C 封装 / 箱体:QFN-20 安装风格:SMD/SMT
SST89V516RD-33-C-QIF 制造商:SST 制造商全称:Silicon Storage Technology, Inc 功能描述:FlashFlex MCU
SST89V516RD-33-I-QIF 制造商:SST 制造商全称:Silicon Storage Technology, Inc 功能描述:FlashFlex MCU
SST89V52RD2 制造商:SST 制造商全称:Silicon Storage Technology, Inc 功能描述:FlashFlex51 MCU
SST89V52RD2/RD 制造商:SST 制造商全称:Silicon Storage Technology, Inc 功能描述:FlashFlex51 MCU