- 您现在的位置：买卖IC网 > PDF目录98142 > SST89V516RD-33-C-PI (SILICON STORAGE TECHNOLOGY INC) 8-BIT, FLASH, 33 MHz, MICROCONTROLLER, PDIP40 PDF资料下载
参数资料
| 型号： | SST89V516RD-33-C-PI |
| 厂商： | SILICON STORAGE TECHNOLOGY INC |
| 元件分类： | 微控制器/微处理器 |
| 英文描述： | 8-BIT, FLASH, 33 MHz, MICROCONTROLLER, PDIP40 |
| 封装： | PLASTIC, MS-011AC, DIP-40 |
| 文件页数： | 58/80页 |
| 文件大小： | 934K |
| 代理商： | SST89V516RD-33-C-PI |
第1页第2页第3页第4页第5页第6页第7页第8页第9页第10页第11页第12页第13页第14页第15页第16页第17页第18页第19页第20页第21页第22页第23页第24页第25页第26页第27页第28页第29页第30页第31页第32页第33页第34页第35页第36页第37页第38页第39页第40页第41页第42页第43页第44页第45页第46页第47页第48页第49页第50页第51页第52页第53页第54页第55页第56页第57页当前第58页第59页第60页第61页第62页第63页第64页第65页第66页第67页第68页第69页第70页第71页第72页第73页第74页第75页第76页第77页第78页第79页第80页
Data Sheet
FlashFlex51 MCU
SST89E516RD2 / SST89E516RD
SST89V516RD2 / SST89V516RD
61
2005 Silicon Storage Technology, Inc.
S71273-01-000
3/05
12.0 POWER-SAVING MODES
The device provides two power saving modes of operation
for applications where power consumption is critical. The
two modes are idle and power-down, see Table 12-1.
12.1 Idle Mode
Idle mode is entered setting the IDL bit in the PCON regis-
ter. In idle mode, the program counter (PC) is stopped. The
system clock continues to run and all interrupts and periph-
erals remain active. The on-chip RAM and the special func-
tion registers hold their data during this mode.
The device exits idle mode through either a system inter-
rupt or a hardware reset. Exiting idle mode via system
interrupt, the start of the interrupt clears the IDL bit and
exits idle mode. After exit the Interrupt Service Routine, the
interrupted program resumes execution beginning at the
instruction immediately following the instruction which
invoked the idle mode. A hardware reset starts the device
similar to a power-on reset.
12.2 Power-down Mode
The power-down mode is entered by setting the PD bit in
the PCON register. In the power-down mode, the clock is
stopped and external interrupts are active for level sensitive
interrupts only. SRAM contents are retained during power-
down, the minimum VDD level is 2.0V.
The device exits power-down mode through either an
enabled external level sensitive interrupt or a hardware
reset. The start of the interrupt clears the PD bit and exits
power-down. Holding the external interrupt pin low restarts
the oscillator, the signal must hold low at least 1024 clock
cycles before bringing back high to complete the exit. Upon
interrupt signal being restored to logic VIH, the first instruc-
tion of the interrupt service routine will execute. A hardware
reset starts the device similar to power-on reset.
To exit properly out of power-down, the reset or external
interrupt should not be executed before the VDD line is
restored to its normal operating voltage. Be sure to hold
VDD voltage long enough at its normal operating level for
the oscillator to restart and stabilize (normally less than
10 ms).
TABLE
12-1: POWER SAVING MODES
Mode
Initiated by
State of MCU
Exited by
Idle Mode
Software
(Set IDL bit in PCON)
MOV PCON, #01H;
CLK is running.
Interrupts, serial port and tim-
ers/counters are active. Pro-
gram Counter is stopped.
ALE and PSEN# signals at a
HIGH level during Idle. All
registers remain unchanged.
Enabled interrupt or hardware reset.
Start of interrupt clears IDL bit and
exits idle mode, after the ISR RETI
instruction, program resumes execu-
tion beginning at the instruction follow-
ing the one that invoked idle mode. A
user could consider placing two or
three NOP instructions after the
instruction that invokes idle mode to
eliminate any problems. A hardware
reset restarts the device similar to a
power-on reset.
Power-down
Mode
Software
(Set PD bit in PCON)
MOV PCON, #02H;
CLK is stopped. On-chip
SRAM and SFR data is main-
tained. ALE and PSEN# sig-
nals at a LOW level during
power -down. External Inter-
rupts are only active for level
sensitive interrupts, if
enabled.
Enabled external level sensitive inter-
rupt or hardware reset. Start of inter-
rupt clears PD bit and exits power-
down mode, after the ISR RETI
instruction program resumes execution
beginning at the instruction following
the one that invoked power-down
mode. A user could consider placing
two or three NOP instructions after the
instruction that invokes power-down
mode to eliminate any problems. A
hardware reset restarts the device sim-
ilar to a power-on reset.
T12-1.0 1273
相关PDF资料 |
PDF描述 |
|---|---|
| SST89V516RD-33-I-PIE | 8-BIT, FLASH, 33 MHz, MICROCONTROLLER, PDIP40 |
| SST89E516RD-40-I-PIE | 8-BIT, FLASH, 40 MHz, MICROCONTROLLER, PDIP40 |
| SST89V554A-33-C-TQJ | 8-BIT, FLASH, 33 MHz, MICROCONTROLLER, PQFP44 |
| SST89E554A-40-C-NJ | 8-BIT, FLASH, 40 MHz, MICROCONTROLLER, PQCC44 |
| SST89E554A-40-I-TQJ | 8-BIT, FLASH, 40 MHz, MICROCONTROLLER, PQFP44 |
相关代理商/技术参数 |
参数描述 |
|---|---|
| SST89V516RD-33-C-PIE | 功能描述:8位微控制器 -MCU 8-Bit 64K+8K Flash 33MHz 3/16-Bit Timer RoHS:否 制造商:Silicon Labs 核心:8051 处理器系列:C8051F39x 数据总线宽度:8 bit 最大时钟频率:50 MHz 程序存储器大小:16 KB 数据 RAM 大小:1 KB 片上 ADC:Yes 工作电源电压:1.8 V to 3.6 V 工作温度范围:- 40 C to + 105 C 封装 / 箱体:QFN-20 安装风格:SMD/SMT |
| SST89V516RD-33-C-QIF | 制造商:SST 制造商全称:Silicon Storage Technology, Inc 功能描述:FlashFlex MCU |
| SST89V516RD-33-I-QIF | 制造商:SST 制造商全称:Silicon Storage Technology, Inc 功能描述:FlashFlex MCU |
| SST89V52RD2 | 制造商:SST 制造商全称:Silicon Storage Technology, Inc 功能描述:FlashFlex51 MCU |
| SST89V52RD2/RD | 制造商:SST 制造商全称:Silicon Storage Technology, Inc 功能描述:FlashFlex51 MCU |
发布紧急采购，3分钟左右您将得到回复。