- 您现在的位置：买卖IC网 > PDF目录98143 > ST10R172LT6 (STMICROELECTRONICS) 16-BIT, 50 MHz, MICROCONTROLLER, PQFP100 PDF资料下载
参数资料
| 型号： | ST10R172LT6 |
| 厂商： | STMICROELECTRONICS |
| 元件分类： | 微控制器/微处理器 |
| 英文描述： | 16-BIT, 50 MHz, MICROCONTROLLER, PQFP100 |
| 封装： | 14 X 14 MM, TQFP-100 |
| 文件页数： | 18/68页 |
| 文件大小： | 657K |
| 代理商： | ST10R172LT6 |
第1页第2页第3页第4页第5页第6页第7页第8页第9页第10页第11页第12页第13页第14页第15页第16页第17页当前第18页第19页第20页第21页第22页第23页第24页第25页第26页第27页第28页第29页第30页第31页第32页第33页第34页第35页第36页第37页第38页第39页第40页第41页第42页第43页第44页第45页第46页第47页第48页第49页第50页第51页第52页第53页第54页第55页第56页第57页第58页第59页第60页第61页第62页第63页第64页第65页第66页第67页第68页
25/68
ST10R172L - SYSTEM RESET
12
SYSTEM RESET
The following type of reset are implemented on the ST10R172L:
Asynchronous hardware reset: Asynchronous reset does not require a stabilized clock
signal on XTAL1 as it is not internally resynchronized, it resets the microcontroller into its
default reset state. Asynchronous reset is required on chip power-up and can be used during
catastrophic situations. The rising edge of the RSTIN pin is internally resynchronized before
exiting the reset condition, therefore, only the entry to hardware reset is asynchronous.
Synchronous hardware reset (warm reset): A warm synchronous hardware reset is
triggered when the reset input signal RSTIN is latched low and Vpp pin is high. The I/Os are
immediately (asynchronously) set in high impedance, RSTOUT is driven low. After RSTIN
negation is detected, a short transition period elapses, during which pending internal hold
states are cancelled and any current internal access cycles are completed, external bus
cycles are aborted. Then, the internal reset sequence is active for 1024 TCL (512 CPU clock
cycles). During this reset sequence, if bit BDRSTEN was previously set by software (bit 3 in
SYSCON register), RSTIN pin is driven low and internal reset signal is asserted to reset the
microcontroller in its default state. Note that after all reset sequence, bit BDRSTEN is cleared.
After the reset sequence has been completed, the RSTIN input is sampled. When the reset
input signal is active at that time the internal reset condition is prolonged until RSTIN
becomes inactive.
Software reset: The reset sequence can be triggered at any time by the protected
instruction SRST (software reset). This instruction can be executed deliberately within a
program, e.g. to leave bootstrap loader mode, or on a hardware trap that reveals a system
failure. As for a synchronous hardware reset, if bit BDRSTEN was previously set by software
(bit 3 in SYSCON register), the reset sequence lasts 1024 TCL (512 CPU clock cycles), and
drives the RSTIN pin low.
Watchdog timer reset: When the watchdog timer is not disabled during the initialization or
serviced regularly during program execution it will overflow and trigger the reset sequence.
Unlike hardware and software resets, the watchdog reset completes a running external bus
cycle if this bus cycle does not use READY, or if READY is sampled active (low) after the
programmed waitstates. When READY is sampled inactive (high) after the programmed
waitstates the running external bus cycle is aborted. Then the internal reset sequence is
started. The watchdog reset cannot occur while the ST10R172L is in bootstrap loader mode.
Bidirectional reset: The bidirectional reset is activated by setting bit BDRSTEN (bit 3 in
SYSCON register). This reset makes the watchdog timer reset and software reset externally
visible. It is active for the duration of an internal reset sequences caused by a watchdog timer
reset and software reset. Therefore, the bidirectional reset transforms an internal watchdog
timer reset or software reset into an external hardware reset with a minimum duration of
1024 TCL.
1
相关PDF资料 |
PDF描述 |
|---|---|
| ST10R272LT6 | 16-BIT, 50 MHz, MICROCONTROLLER, PQFP100 |
| ST16C452PSIJ68 | 2 CHANNEL(S), SERIAL COMM CONTROLLER, PQCC68 |
| ST16C452ATIJ68 | 2 CHANNEL(S), SERIAL COMM CONTROLLER, PQCC68 |
| ST16C654IQ64/TR | 4 CHANNEL(S), 1.5M bps, SERIAL COMM CONTROLLER, PQFP64 |
| ST18931CR | 16-BIT, 50 MHz, OTHER DSP, CPGA121 |
相关代理商/技术参数 |
参数描述 |
|---|---|
| ST10R262-T1 | 制造商:STMicroelectronics 功能描述: 制造商:STMicroelectronics 功能描述:10R262-T1 |
| ST10R272 | 制造商:STMICROELECTRONICS 制造商全称:STMicroelectronics 功能描述:16-BIT LOW VOLTAGE ROMLESS MCU WITH MAC |
| ST10R272L | 制造商:STMICROELECTRONICS 制造商全称:STMicroelectronics 功能描述:16-BIT LOW VOLTAGE ROMLESS MCU WITH MAC |
| ST10R272L_ER | 制造商:未知厂家 制造商全称:未知厂家 功能描述:16-BIT LOW VOLTAGE ROMLESS MCU WITH MAC (ERRATA SHEET) |
| ST10R272L-B0 | 制造商:STMICROELECTRONICS 制造商全称:STMicroelectronics 功能描述:16-BIT ROMLESS LOW VOLTAGE MCU WITH MAC |
发布紧急采购，3分钟左右您将得到回复。