收藏本站
参数资料
型号： ST72C171K2B6
厂商： STMICROELECTRONICS
元件分类： 微控制器/微处理器
英文描述： 8-BIT, FLASH, 8 MHz, MICROCONTROLLER, PDIP32
封装： SHRINK, PLASTIC, DIP-32
文件页数： 141/152页
文件大小： 2156K
代理商： ST72C171K2B6
ST72C171
89/152
7.8 SERIAL PERIPHERAL INTERFACE (SPI)
7.8.1 Introduction
The Serial Peripheral Interface (SPI) allows full-
duplex, synchronous, serial communication with
external devices. An SPI system may consist of a
master and one or more slaves or a system in
which devices may be either masters or slaves.
The SPI is normally used for communication be-
tween the microcontroller and external peripherals
or another microcontroller.
Refer to the Pin Description chapter for the device-
specific pin-out.
7.8.2 Main Features
s
Full duplex, three-wire synchronous transfers
s
Master or slave operation
s
Four master mode frequencies
s
Maximum slave mode frequency = fCPU/2.
s
Four programmable master bit rates
s
Programmable clock polarity and phase
s
End of transfer interrupt flag
s
Write collision flag protection
s
Master mode fault protection capability.
7.8.3 General description
The SPI is connected to external devices through
4 alternate pins:
– MISO: Master In Slave Out pin
– MOSI: Master Out Slave In pin
– SCK: Serial Clock pin
– SS: Slave select pin
A basic example of interconnections between a
single master and a single slave is illustrated on
Figure 49.
The MOSI pins are connected together as are
MISO pins. In this way data is transferred serially
between master and slave (most significant bit
first).
When the master device transmits data to a slave
device via MOSI pin, the slave device responds by
sending data to the master device via the MISO
pin. This implies full duplex transmission with both
data out and data in synchronized with the same
clock signal (which is provided by the master de-
vice via the SCK pin).
Thus, the byte transmitted is replaced by the byte
received and eliminates the need for separate
transmit-empty and receiver-full bits. A status flag
is used to indicate that the I/O operation is com-
plete.
Four possible data/clock timing relationships may
be chosen (see Figure 52) but master and slave
must be programmed with the same timing mode.
Figure 49. Serial Peripheral Interface Master/Slave
8-BIT SHIFT REGISTER
SPI
CLOCK
GENERATOR
8-BIT SHIFT REGISTER
MISO
MOSI
MISO
SCK
SLAVE
MASTER
SS
+5V
MSBit
LSBit
MSBit
LSBit
相关PDF资料
PDF描述
ST72E85A5G0 8-BIT, UVPROM, 4.332 MHz, MICROCONTROLLER, CQFP80
ST72F321J9T7 8-BIT, FLASH, 8 MHz, MICROCONTROLLER, PQFP44
ST72F321J7T3 8-BIT, FLASH, 8 MHz, MICROCONTROLLER, PQFP44
ST72F321J7T1 8-BIT, FLASH, 8 MHz, MICROCONTROLLER, PQFP44
ST72F321J9T5 8-BIT, FLASH, 8 MHz, MICROCONTROLLER, PQFP44
相关代理商/技术参数
参数描述
ST72C171K2M6 功能描述:8位微控制器 -MCU Flash 8K SPI/SCI RoHS:否 制造商:Silicon Labs 核心:8051 处理器系列:C8051F39x 数据总线宽度:8 bit 最大时钟频率:50 MHz 程序存储器大小:16 KB 数据 RAM 大小:1 KB 片上 ADC:Yes 工作电源电压:1.8 V to 3.6 V 工作温度范围:- 40 C to + 105 C 封装 / 箱体:QFN-20 安装风格:SMD/SMT
ST72C215G2B6 功能描述:8位微控制器 -MCU Flash 8K SPI RoHS:否 制造商:Silicon Labs 核心:8051 处理器系列:C8051F39x 数据总线宽度:8 bit 最大时钟频率:50 MHz 程序存储器大小:16 KB 数据 RAM 大小:1 KB 片上 ADC:Yes 工作电源电压:1.8 V to 3.6 V 工作温度范围:- 40 C to + 105 C 封装 / 箱体:QFN-20 安装风格:SMD/SMT
ST72C215G2M3 制造商:STMicroelectronics 功能描述:MCU 8-Bit ST7 CISC 8KB Flash 3.3V/5V 28-Pin SO Tube 制造商:STMicroelectronics 功能描述:MCU 8BIT ST7 CISC 8KB FLASH 3.3V/5V 28SOIC - Rail/Tube
ST72C215G2M5 制造商:STMicroelectronics 功能描述:MCU 8BIT ST7 CISC 8KB FLASH 3.3V/5V 28SOIC - Rail/Tube
ST72C215G2M6 功能描述:8位微控制器 -MCU Flash 8K SPI RoHS:否 制造商:Silicon Labs 核心:8051 处理器系列:C8051F39x 数据总线宽度:8 bit 最大时钟频率:50 MHz 程序存储器大小:16 KB 数据 RAM 大小:1 KB 片上 ADC:Yes 工作电源电压:1.8 V to 3.6 V 工作温度范围:- 40 C to + 105 C 封装 / 箱体:QFN-20 安装风格:SMD/SMT
发布紧急采购，3分钟左右您将得到回复。

采购需求

(若只采购一条型号，填写一行即可)

发布成功！您可以继续发布采购。也可以进入我的后台，查看报价

发布成功！您可以继续发布采购。也可以进入我的后台，查看报价

*型号 *数量 厂商 批号 封装
添加更多采购

我的联系方式

*
*
*