参数资料
| 型号： | TISP61089BDR |
| 厂商： | Bourns Inc. |
| 文件页数： | 11/20页 |
| 文件大小： | 0K |
| 描述： | SURGE SUPP SLIC PROG HV 8-SOP |
| 标准包装： | 2,500 |
| 电压 - 击穿： | 64V |
| 电压 - 断路： | 170V |
| 电流 - 峰值脉冲(10 x 1000µs)： | 30A |
| 电流 - 保持 (Ih)： | 150mA |
| 元件数： | 2 |
| 电容： | 100pF |
| 封装/外壳： | 8-SOIC（0.154"，3.90mm 宽） |
| 包装： | 带卷 (TR) |
TISP61089B High Voltage Ringing SLIC Protector
Application Circuit
Figure 12 shows a typical TISP61089B SLIC card protection circuit. The incoming line conductors, Ring (R) and Tip (T), connect to the relay
matrix via the series overcurrent protection. Fusible resistors, fuses and positive temperature coefficient (PTC) resistors can be used for
overcurrent protection. Resistors will reduce the prospective current from the surge generator for both the TISP61089B and the ring/test
protector. The TISP7xxxF3 protector has the same protection voltage for any terminal pair. This protector is used when the ring generator
configuration may be ground or battery-backed. For dedicated ground-backed ringing generators, the TISP3xxxF3 gives better protection as
its inter-conductor protection voltage is twice the conductor to ground value.
Relay contacts 3a and 3b connect the line conductors to the SLIC via the TISP61089B protector. The protector gate reference voltage comes
from the SLIC negative supply (V BATH ). A 220 nF gate capacitor sources the high gate current pulses caused by fast rising impulses.
LSSGR 1089
GR-1089-CORE, “1089”, covers electromagnetic compatibility and electrical safety generic criteria for US network telecommunication
equipment. It is a module in Volume 3 of LSSGR (LATA (Local Access Transport Area) Switching Systems Generic Requirements,
FR-NWT-000064). In ‘1089, surge and power fault immunity tests are done at two levels. After first-level testing, the equipment shall not be
damaged and shall continue to operate correctly. Under second-level testing, the equipment shall not become a safety hazard. The equipment
is permitted to fail as a result of second-level testing. When the equipment is to be located on customer premises, second-level testing
includes a wiring simulator test, which requires the equipment to reduce the power fault current below certain values.
The following clauses reference the ‘1089 section and calculate the protector stress levels. The TISP61089B needs a 40 ? series resistor to
survive second-level surge testing. To survive first-level testing and possibly fail under second-level testing allows lower resistor value of 25 ?
to be used. Tabulated current values are given for both 40 ? and 25 ? series resistor values.
‘1089 Section 4.5.5 - Test Generators
The generic form of test generator is shown in Figure 13. It emphasises that multiple outputs must be independent, i.e. the loading condition of
one output must not affect the waveforms of the other outputs. It is a requirement that the open-circuit voltage and short circuit current
waveforms be recorded for each generator output used for testing. The fictive impedance of a generator output is defined as the peak open-
circuit voltage divided by the peak short-circuit current. Specified impulse waveshapes are maximum rise and minimum decay times. Thus, the
10/1000 waveshape should be interpreted as <10/>1000 and not the usually defined nominal values which have a tolerance.
Z
Z
Z
Z
Output 1
Output 2
Output n
Output n + 1
or
Z is the fictive
current-limiting
impedance in
each output feed
Return
Generic Lightning or AC Test Generator
AI6XCJ
Figure 13. ‘1089 Test Generators
OCTOBER 2000 - REVISED JULY 2008
Specifications are subject to change without notice.
Customers should verify actual device performance in their specific applications.
相关PDF资料 |
PDF描述 |
|---|---|
| TISP61089BSDR-S | PROTECTOR QUAD PROGRAMMABLE |
| TISP61089HDMR-S | SURGE PROT THYRIST 155V SLIC |
| TISP61089QDR-S | PROTECTOR PROGRAMMABLE SLIC |
| TISP61089SDR-S | PROTECTOR OVER VOLTAGE |
| TISP6NTP2ADR | SURGE SUPP QUAD PROG SOP |
相关代理商/技术参数 |
参数描述 |
|---|---|
| TISP61089BDR-S | 功能描述:SCR Dual P Gate Forward Conducting RoHS:否 制造商:STMicroelectronics 最大转折电流 IBO:480 A 额定重复关闭状态电压 VDRM:600 V 关闭状态漏泄电流（在 VDRM IDRM 下）:5 uA 开启状态 RMS 电流 (It RMS): 正向电压下降:1.6 V 栅触发电压 (Vgt):1.3 V 最大栅极峰值反向电压:5 V 栅触发电流 (Igt):35 mA 保持电流（Ih 最大值）:75 mA 安装风格:Through Hole 封装 / 箱体:TO-220 封装:Tube |
| TISP61089BDR-T | 功能描述:SCR PROTECTOR - PROGRAMMABLE SLIC PROTECT RoHS:否 制造商:STMicroelectronics 最大转折电流 IBO:480 A 额定重复关闭状态电压 VDRM:600 V 关闭状态漏泄电流（在 VDRM IDRM 下）:5 uA 开启状态 RMS 电流 (It RMS): 正向电压下降:1.6 V 栅触发电压 (Vgt):1.3 V 最大栅极峰值反向电压:5 V 栅触发电流 (Igt):35 mA 保持电流（Ih 最大值）:75 mA 安装风格:Through Hole 封装 / 箱体:TO-220 封装:Tube |
| TISP61089BDS | 制造商:Bourns Inc 功能描述: |
| TISP61089BD-S | 功能描述:SCR Dual P Gate Forward Conducting RoHS:否 制造商:STMicroelectronics 最大转折电流 IBO:480 A 额定重复关闭状态电压 VDRM:600 V 关闭状态漏泄电流（在 VDRM IDRM 下）:5 uA 开启状态 RMS 电流 (It RMS): 正向电压下降:1.6 V 栅触发电压 (Vgt):1.3 V 最大栅极峰值反向电压:5 V 栅触发电流 (Igt):35 mA 保持电流（Ih 最大值）:75 mA 安装风格:Through Hole 封装 / 箱体:TO-220 封装:Tube |
| TISP61089BGDR-S | 功能描述:PROTECTOR PROGRAMMABLE SLIC RoHS:是 类别:过电压，电流，温度装置 >> TVS - 晶闸管 系列:- 产品变化通告:Product Discontinuation 19/Jul/2012 标准包装:2,500 系列:- 电压 - 击穿:400V 电压 - 断路:320V 电压 - 导通状态:4V 电流 - 峰值脉冲(8 x 20µs):250A 电流 - 峰值脉冲(10 x 1000µs):80A 电流 - 保持 (Ih):150mA 元件数:1 电容:29pF 封装/外壳:DO-214AA，SMB 包装:带卷 (TR) |
发布紧急采购，3分钟左右您将得到回复。