参数资料
| 型号： | TISP61089BDR |
| 厂商： | Bourns Inc. |
| 文件页数： | 16/20页 |
| 文件大小： | 0K |
| 描述： | SURGE SUPP SLIC PROG HV 8-SOP |
| 标准包装： | 2,500 |
| 电压 - 击穿： | 64V |
| 电压 - 断路： | 170V |
| 电流 - 峰值脉冲(10 x 1000µs)： | 30A |
| 电流 - 保持 (Ih)： | 150mA |
| 元件数： | 2 |
| 电容： | 100pF |
| 封装/外壳： | 8-SOIC（0.154"，3.90mm 宽） |
| 包装： | 带卷 (TR) |
TISP61089B High Voltage Ringing SLIC Protector
‘1089 Section 4.5.13 - Second-Level Power Fault Testing for Central Office Equipment (Continued)
Table 6. Second-Level Power Fault Currents
Test
#
AC Duration
s
Open-circuit
RMS Voltage
V
Short-circuit
RMS Current
A
No
of
Tests
Test
Connections
Primary
Fitted
Source
Resistance
?
TISP61089B I TM
A (peak)
R s = 25 ? R s = 40 ?
1
2
3
4
5
900
5
5
900
900
120
277
600
600
100 to
600
600
25
60
7
0.37 to
2.2
0.09
1
1
1
1
60
Transverse &
Longitudinal
Transverse &
Longitudinal
Transverse &
Longitudinal
Transverse &
Longitudinal
Differential
No
No
No
No
No
5
11
10
86
270
Capacitive
2x5.7
2x11
2x24
2x7.7
2x2.9
2x0.09
2x3.8
2x7.7
2x17
2x6.8
2x2.7
2x0.09
NOTES: 1. If the equipment contains a voltage-limiting device or a current-limiting device, these tests are repeated at a level just below the
thresholds of the limiting devices.
2. Test 5 uses a special circuit with transformer coupled a.c. and capacitive feed.
‘1089 Section 4.5.15 - Second-Level Power Fault Testing for Equipment Located on the Customer Premise
This test, Table 7, is for network equipment located on the customer premises. The purpose is to ensure that the feed wiring does not become
a hazard due to excessive current. This testing is similar to the Section 4.5.11 testing. If the equipment is directly wired, the wiring simulator
described in Section 4.5.11 is replaced by a one-foot section of 26 AWG wrapped in cheesecloth. The equipment fails if an open circuit occurs
or the cheesecloth is damaged.
Table 7 shows the test conditions for this section. Columns 7 and 8 show the prospective currents using R S values of 25 ? and 40 ? . For the
TISP61089B to survive, the series overcurrent protection to operate before the TISP61089B current-time ratings are exceeded.
Table 7. Customer Premise Wiring Simulator Testing
AC Duration
s
Open-circuit
RMS Voltage
V
Short-circuit
RMS Current
A
Test
Connections
Primary
Fitted
Source
Resistance
?
TISP61089B I TM
A (peak)
R s = 25 ? R s = 40 ?
900
0 to 600
0 to 30
Transverse & Longitudinal
No
20
0 to 2x 19
0 to 2x 14
NOTE:
1. If the equipment interrupts the current before the 600 V rms level is reached, a second piece of equipment is tested. The second
piece of equipment shall withstand 600 V rms applied for 900 s without causing a hazard.
‘1089 Section 4.5.16 - Second-Level Intra-Building Power Fault Testing for Equipment Located on the Customer Premise
This test, Table 8, is for network equipment ports that do not serve outside lines. For standard plugable premise wiring, the wiring simulator
fuse shall be used for testing. Where direct wiring occurs, the simulator shall consist of a length of the wire used wrapped in cheesecloth. The
equipment fails if a hazard occurs or a wiring simulator open circuit occurs or the cheesecloth is damaged.
Table 8. Second-Level Power Fault Currents
Test
#
AC Duration
s
Open-circuit
RMS Voltage
V
Short-circuit
RMS Current
A
No
of
Tests
Test
Connections
Primary
Fitted
Source
Resistance
?
TISP61089B I TM
A (peak)
R s = 8 ? R s = 25 ? R s = 40 ?
1
900
120
25
1
Transverse &
Longitudinal
No
5
2x13
2x5.7
2x3.8
NOTE:
1. If the equipment contains a voltage-limiting device or a current-limiting device, these tests are repeated at a level just below the
thresholds of the limiting devices.
OCTOBER 2000 - REVISED JULY 2008
Specifications are subject to change without notice.
Customers should verify actual device performance in their specific applications.
相关PDF资料 |
PDF描述 |
|---|---|
| TISP61089BSDR-S | PROTECTOR QUAD PROGRAMMABLE |
| TISP61089HDMR-S | SURGE PROT THYRIST 155V SLIC |
| TISP61089QDR-S | PROTECTOR PROGRAMMABLE SLIC |
| TISP61089SDR-S | PROTECTOR OVER VOLTAGE |
| TISP6NTP2ADR | SURGE SUPP QUAD PROG SOP |
相关代理商/技术参数 |
参数描述 |
|---|---|
| TISP61089BDR-S | 功能描述:SCR Dual P Gate Forward Conducting RoHS:否 制造商:STMicroelectronics 最大转折电流 IBO:480 A 额定重复关闭状态电压 VDRM:600 V 关闭状态漏泄电流（在 VDRM IDRM 下）:5 uA 开启状态 RMS 电流 (It RMS): 正向电压下降:1.6 V 栅触发电压 (Vgt):1.3 V 最大栅极峰值反向电压:5 V 栅触发电流 (Igt):35 mA 保持电流（Ih 最大值）:75 mA 安装风格:Through Hole 封装 / 箱体:TO-220 封装:Tube |
| TISP61089BDR-T | 功能描述:SCR PROTECTOR - PROGRAMMABLE SLIC PROTECT RoHS:否 制造商:STMicroelectronics 最大转折电流 IBO:480 A 额定重复关闭状态电压 VDRM:600 V 关闭状态漏泄电流（在 VDRM IDRM 下）:5 uA 开启状态 RMS 电流 (It RMS): 正向电压下降:1.6 V 栅触发电压 (Vgt):1.3 V 最大栅极峰值反向电压:5 V 栅触发电流 (Igt):35 mA 保持电流（Ih 最大值）:75 mA 安装风格:Through Hole 封装 / 箱体:TO-220 封装:Tube |
| TISP61089BDS | 制造商:Bourns Inc 功能描述: |
| TISP61089BD-S | 功能描述:SCR Dual P Gate Forward Conducting RoHS:否 制造商:STMicroelectronics 最大转折电流 IBO:480 A 额定重复关闭状态电压 VDRM:600 V 关闭状态漏泄电流（在 VDRM IDRM 下）:5 uA 开启状态 RMS 电流 (It RMS): 正向电压下降:1.6 V 栅触发电压 (Vgt):1.3 V 最大栅极峰值反向电压:5 V 栅触发电流 (Igt):35 mA 保持电流（Ih 最大值）:75 mA 安装风格:Through Hole 封装 / 箱体:TO-220 封装:Tube |
| TISP61089BGDR-S | 功能描述:PROTECTOR PROGRAMMABLE SLIC RoHS:是 类别:过电压，电流，温度装置 >> TVS - 晶闸管 系列:- 产品变化通告:Product Discontinuation 19/Jul/2012 标准包装:2,500 系列:- 电压 - 击穿:400V 电压 - 断路:320V 电压 - 导通状态:4V 电流 - 峰值脉冲(8 x 20µs):250A 电流 - 峰值脉冲(10 x 1000µs):80A 电流 - 保持 (Ih):150mA 元件数:1 电容:29pF 封装/外壳:DO-214AA，SMB 包装:带卷 (TR) |
发布紧急采购，3分钟左右您将得到回复。